DLA MIL-DTL-83723 72 E-2009 CONNECTOR ELECTRIC (CIRCULAR ENVIRONMENT RESISTING) RECEPTACLE (FLANGE MOUNT BAYONET COUPLING CRIMP PIN CONTACT) (SERIES III CLASSES A G M R T W AND Z).pdf

1、 MIL-DTL-83723/72E 19 August 2009 SUPERSEDING MIL-DTL-83723/72D 15 September 2006 DETAIL SPECIFICATION SHEET CONNECTOR, ELECTRIC, (CIRCULAR, ENVIRONMENT RESISTING), RECEPTACLE, (FLANGE MOUNT, BAYONET COUPLING, CRIMP PIN CONTACT) (SERIES III, CLASSES A, G, M, R, T, W AND Z) This specification is appr

2、oved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-83723. FIGURE 1. Dimensions and configurations. AMSC N/A FSC 5935 INCH-POUND Provided by IHSNot for ResaleNo re

3、production or networking permitted without license from IHS-,-,-MIL-DTL-83723/72E 2 FIGURE 1. Dimensions and configurations - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83723/72E 3 Shell size A C D max F J max K L S +.005 -.00

4、0 8 .120 .428 .433 .312 .536 .531 .561 .594 .812 .508 10 .120 .530 .535 .388 .659 .654 .696 .719 .937 .636 12 .120 .700 .705 .558 .829 .824 .875 .812 1.031 .806 14 .120 .769 .774 .627 .898 .893 .935 .906 1.125 .875 16 .120 .869 .901 .772 1.025 1.020 1.062 .969 1.250 1.002 18 .120 1.002 1.007 .860 1.

5、131 1.126 1.187 1.062 1.343 1.108 20 .120 1.127 1.132 .985 1.256 1.251 1.312 1.156 1.437 1.233 22 .120 1.252 1.257 1.110 1.381 1.376 1.437 1.250 1.562 1.358 24 .149 1.377 1.382 1.235 1.506 1.501 1.562 1.375 1.703 1.483 FIGURE 1. Dimensions and configurations - Continued. Provided by IHSNot for Resal

6、eNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83723/72E 4 Inches mm Inches mm Inches mm Inches mm Inches mm .0025 .005 .008 .015 .018 .020 .022 .032 .042 .046 .052 .065 .069 .071 .072 .076 .084 .089 .090 .094 .097 .101 .106 .112 0.06 0.13 0.20 0.38 0.46 0.51 0.56 0.81

7、 1.07 1.17 1.32 1.65 1.75 1.80 1.83 1.93 2.13 2.26 2.29 2.39 2.46 2.57 2.69 2.84 .120 .125 .138 .144 .149 .198 .204 .211 .250 .259 .312 .366 .376 .378 .380 .388 .392 .428 .433 .490 .508 .530 .531 .535 3.05 3.18 3.51 3.66 3.78 5.03 5.18 5.36 6.35 6.58 7.92 9.30 9.55 9.60 9.65 9.86 9.96 10.87 11.00 12

8、.45 12.90 13.46 13.49 13.59 .536 .540 .558 .560 .561 .594 .627 .636 .654 .659 .696 .700 .705 .708 .719 .728 .769 .772 .774 .806 .812 .824 .829 .860 13.61 13.72 14.17 14.22 14.25 15.09 15.93 16.15 16.61 16.74 17.68 17.78 17.91 17.98 18.26 19.49 19.53 19.61 19.66 20.47 20.62 20.93 21.06 21.84 .875 .89

9、3 .896 .898 .901 .906 .935 .937 .969 .985 1.002 1.007 1.020 1.025 1.062 1.070 1.108 1.125 1.126 1.127 1.131 1.132 1.156 1.187 22.23 22.68 22.76 22.81 22.89 23.01 23.75 23.80 24.61 25.02 25.45 25.58 25.91 26.04 26.97 27.18 28.14 28.58 28.60 28.63 28.73 28.75 29.36 30.15 1.233 1.235 1.250 1.251 1.252

10、1.256 1.257 1.312 1.343 1.375 1.376 1.377 1.381 1.382 1.385 1.437 1.483 1.501 1.506 1.562 1.703 31.32 31.37 31.75 31.78 31.80 31.90 31.93 33.32 34.11 34.93 34.95 34.98 35.08 35.10 35.18 36.50 37.66 38.13 38.25 39.67 43.26 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for inform

11、ation only. 3. Unless otherwise specified, tolerances are .005 (0.13 mm) for three place decimals, .01 (0.25 mm) for two place decimals and 1 for all angles. 4. Rear accessory interchangeability dimensions shall be accordance with SAE-AS85049. 5. The centerline of indicated projection must be locate

12、d on vertical centerline 2. 6. See table I for contact cavities requiring this dimension. FIGURE 1. Dimensions and configurations - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83723/72E 5 REQUIREMENTS: Dimensions and configurat

13、ion: See figure 1. For insert arrangements, see MIL-STD-1554 and table I. TABLE I. Inserts requiring reduced diameters for raised seal barriers on contact cavities. Shell size Insert arrangements Contact cavities 8 03 1, 2, and 3 10 06 1, 2, 3, 4, 5, 6 For connector accessories: See SAE-AS85049. Thi

14、s connector mates with MIL-DTL-83723/75 and /77. Part or Identifying Number (PIN) example: M83723/ 72 W 22 55 N Military designation Specification sheet number Class Shell size Insert arrangement Polarizing position Changes from previous issue. Marginal notations are not used in this revision to ide

15、ntify changes with respect to the previous issue due to the extent of the changes. Referenced documents. In addition to MIL-DTL-83723, this document references the following: MIL-DTL-83723/75 MIL-DTL-83723/77 MIL-STD-1554 SAE-AS85049 Provided by IHSNot for ResaleNo reproduction or networking permitt

16、ed without license from IHS-,-,-MIL-DTL-83723/72E 6 CONCLUDING MATERIAL Custodians: Preparing activity: Army - CR DLA - CC Navy - AS Air Force - 85 (Project 5935-2008-126) DLA - CC Review activities: Army - AR, MI Navy - EC Air Force 19, 99 NOTE: The activities listed above were interested in this d

17、ocument as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-