DLA MIL-DTL-83723 81 F-2010 CONNECTORS ELECTRICAL (CIRCULAR ENVIRONMENT RESISTING) RECEPTACLE (SINGLE HOLE MOUNT BAYONET COUPLING SOLDER PIN CONTACT) (SERIES III CLASSES H J L P AN.pdf

1、 MIL-DTL-83723/81F 1 October 2010 SUPERSEDING MIL-DTL-83723/81E 20 October 2000 DETAIL SPECIFICATION SHEET CONNECTORS, ELECTRICAL, (CIRCULAR, ENVIRONMENT RESISTING), RECEPTACLE, (SINGLE HOLE MOUNT, BAYONET COUPLING, SOLDER PIN CONTACT), (SERIES III, CLASSES H, J, L, P AND Y) This specification is ap

2、proved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-83723. FIGURE 1. Dimensions and configurations. AMSC N/A FSC 5935 INCH-POUND Provided by IHSNot for ResaleNo

3、reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83723/81F 2 FIGURE 1. Dimensions and configurations - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83723/81F 3 Shell size A B C D E F N thread 8 .481 .461

4、 .137 .097 .428 .433 .312 .536 .531 .561 .625-20 UN-2A 10 .481 .461 .137 .097 .530 .535 .388 .659 .654 .696 .750-20 UNEF-2A 12 .481 .461 .137 .097 .700 .705 .558 .829 .824 .875 .9375-20 UNEF-2A 14 .481 .461 .137 .097 .769 .774 .627 .898 .893 .935 1.000-20 UNEF-2A 16 .481 .461 .137 .097 .896 .901 .77

5、2 1.025 1.020 1.062 1.125-20 UN-2A 18 .481 .461 .137 .097 1.002 1.007 .860 1.131 1.126 1.187 1.250-18 UNEF-2A 20 .481 .461 .137 .097 1.127 1.132 .985 1.256 1.251 1.312 1.375-18 UNEF-2A 22 .481 .461 .168 .128 1.252 1.257 1.110 1.381 1.376 1.437 1.500-18 UNEF-2A 24 .481 .461 .168 .128 1.377 1.382 1.23

6、5 1.506 1.501 1.562 1.625-18 UNEF-2A FIGURE 1. Dimensions and configurations - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83723/81F 4 Shell size U V W S + .005 - .000 EE FF MM JJ 8 .670 .984 .974 1.068 .508 .605 .635 .493 .596

7、 .590 10 .777 1.109 1.099 1.192 .636 .730 .760 .555 .721 .715 12 .965 1.296 1.286 1.380 .806 .917 .947 .743 .908 .902 14 1.090 1.396 1.386 1.505 .875 .980 1.010 .805 .971 .965 16 1.215 1.521 1.511 1.630 1.002 1.105 1.135 .931 1.096 1.090 18 1.340 1.646 1.636 1.765 1.108 1.229 1.260 1.055 1.220 1.214

8、 20 1.465 1.771 1.761 1.860 1.233 1.354 1.385 1.243 1.345 1.339 22 1.574 1.959 1.949 2.068 1.358 1.479 1.510 1.305 1.470 1.464 24 1.699 2.084 2.074 2.160 1.483 1.604 1.635 1.493 1.595 1.589 FIGURE 1. Dimensions and configurations - Continued. Provided by IHSNot for ResaleNo reproduction or networkin

9、g permitted without license from IHS-,-,-MIL-DTL-83723/81F 5 Inches mm Inches mm Inches mm Inches mm Inches mm .003 0.08 .312 7.92 .761 19.33 1.099 27.91 1.386 35.20 .004 0.10 .366 9.30 .769 19.53 1.105 28.07 1.396 35.46 .005 0.13 .376 9.55 .772 19.61 1.109 28.17 1.437 36.50 .008 0.20 .378 9.60 .774

10、 19.66 1.110 28.19 1.464 37.19 .015 0.38 .380 9.65 .777 19.74 1.125 28.58 1.465 37.21 .018 0.46 .388 9.86 .781 19.84 1.126 28.60 1.470 37.34 .019 0.48 .392 9.96 .805 20.45 1.127 28.63 1.479 37.57 .020 0.51 .428 10.87 .824 20.93 1.131 28.73 1.493 37.92 .022 0.56 .433 11.00 .826 20.98 1.132 28.75 1.50

11、0 38.10 .032 0.81 .461 11.71 .829 21.06 1.135 28.82 1.501 38.13 .050 1.27 .481 12.21 .860 21.84 1.182 30.02 1.506 38.25 .054 1.37 .490 12.45 .875 22.23 1.187 30.15 1.510 38.35 .068 1.73 .493 12.52 .893 22.68 1.192 30.28 1.511 38.38 .071 1.80 .530 13.46 .896 22.76 1.214 30.84 1.521 38.63 .074 1.88 .5

12、31 13.49 .898 22.81 1.215 30.86 1.562 39.67 .076 1.93 .535 13.59 .901 22.89 1.220 30.99 1.574 39.98 .084 2.13 .536 13.61 .902 22.91 1.229 31.22 1.589 40.36 .089 2.26 .540 13.72 .908 23.06 1.235 31.37 1.595 40.51 .090 2.29 .555 14.10 .917 23.29 1.243 31.57 1.604 40.74 .093 2.36 .558 14.17 .931 23.65

13、1.250 31.75 1.625 41.28 .094 2.39 .560 14.22 .935 23.75 1.251 31.78 1.630 41.40 .097 2.46 .561 14.25 .9357 23.77 1.252 31.80 1.635 41.53 .098 2.49 .590 14.99 .942 23.93 1.256 31.90 1.636 41.55 .101 2.57 .596 15.14 .947 24.05 1.257 31.93 1.646 41.81 .106 2.69 .605 15.37 .965 24.51 1.260 32.00 1.699 4

14、3.15 .112 2.84 .625 15.88 .971 24.66 1.286 32.66 1.756 44.60 .125 3.18 .627 15.93 .974 24.74 1.296 32.92 1.771 44.98 .128 3.25 .635 16.13 .980 24.89 1.305 33.15 1.860 47.24 .137 3.48 .654 16.61 .984 24.99 1.312 33.32 1.949 49.50 .138 3.51 .659 16.74 .985 25.02 1.339 34.01 1.959 49.76 .140 3.58 .670

15、17.02 1.000 25.40 1.340 34.03 2.068 52.53 .144 3.66 .696 17.68 1.002 25.45 1.345 34.16 2.074 52.68 .146 3.71 .700 17.78 1.010 25.65 1.354 34.39 2.084 52.93 .165 4.19 .705 17.92 1.020 25.91 1.375 34.93 2.160 54.86 .168 4.27 .715 18.16 1.025 26.04 1.376 34.95 .198 5.03 .721 18.31 1.055 26.80 1.377 34.

16、98 .204 5.18 .730 18.54 1.062 26.97 1.380 35.05 .225 5.72 .743 18.87 1.068 27.13 1.381 35.08 .235 5.97 .750 19.05 1.090 27.69 1.382 35.10 .259 6.58 .760 19.30 1.096 27.84 1.385 35.18 FIGURE 1. Dimensions and configurations - Continued. Provided by IHSNot for ResaleNo reproduction or networking permi

17、tted without license from IHS-,-,-MIL-DTL-83723/81F 6 NOTES: (Notes 4 through 8 apply to contacts only). 1. Dimensions are in inches. 2. Metric equivalents are given for information only. 3. Unless otherwise specified, tolerances are .005 inches (0.13 mm) for three place decimals, .01 inches (0.25 m

18、m) for two place decimals and 1 for all angles. 4. Dimensions apply after plating. 5. Surface finish: 63 ( ) all over in accordance with ASME-B46.1, unless otherwise specified. 6. Remove all burrs and sharp edges .003 to .005 inches (0.076 to 0.127 mm) R. 7. Diameters to be concentric within .004 in

19、ches (0.102 mm) TIR. 8. Diameter in the same cross-sectional plane to be concentric with each other within .003 inches (0.076 mm) TIR. 9. See table I for contact cavities requiring this dimension. FIGURE 1. Dimensions and configurations - Continued. REQUIREMENTS: Dimensions and configuration: See fi

20、gure 1. This connector mates with MIL-DTL-83723/75 and /77. For insert arrangements, see MIL-STD-1554 and table I. TABLE I. Insert arrangements requiring reduced diameters for raised seal barriers on contact cavities as indicated. Shell size Insert arrangements Contact cavities 8 03, 98 1, 2, and 3

21、10 06 1, 2, 3, 4, 5, and 6 Connector accessories: See SAE-AS85049. O-ring: See MIL-DTL-83723. Part or Identifying Number (PIN) example: M83723/ 81 H 22 55 N Military designation Specification sheet number Class Shell size Insert arrangement Polarizing position Provided by IHSNot for ResaleNo reprodu

22、ction or networking permitted without license from IHS-,-,-MIL-DTL-83723/81F 7 Changes from previous issue. Marginal notations are not used in this revision to identify changes with respect to the previous issue due to the extent of the changes. Referenced documents. In addition to MIL-DTL-83723, th

23、is document references the following: MIL-DTL-83723/75 MIL-DTL-83723/77 MIL-STD-1554 MS3186 ASME-B46.1 SAE-AS85049 CONCLUDING MATERIAL Custodians: Preparing activity: Army - CR DLA - CC Navy - AS Air Force 85 (Project 5935-2010-050) DLA - CC Review activities: Army - AR, AV, MI Navy - EC Air Force -

24、 19, 99 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-