DLA MIL-DTL-83723 83 E-2009 CONNECTORS ELECTRICAL (CIRCULAR ENVIRONMENT RESISTING) RECEPTACLE (FLANGE MOUNT THREADED COUPLING CRIMP PIN CONTACT) (SERIES III CLASSES A G K M N R S T.pdf

1、 DETAIL SPECIFICATION SHEET CONNECTORS, ELECTRICAL, (CIRCULAR, ENVIRONMENT RESISTING), RECEPTACLE, (FLANGE MOUNT, THREADED COUPLING, CRIMP PIN CONTACT), (SERIES III, CLASSES A, G, K, M, N, R, S, T, W AND Z) This specification is approved for use by all Departments and Agencies of the Department of D

2、efense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-83723. FIGURE 1. Classes A, G, K, M, R, T, W and Z. AMSC N/A FSC 5935 INCH-POUND MIL-DTL-83723/83E 1 October 2009 SUPERSEDING MIL-C-83723/83D 30 June 1992 Provided by IHSNot for

3、ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83723/83E 2 FIGURE 1. Classes A, G, K, M, R, T, W and Z - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83723/83E 3 Inches mm Inches mm Inches mm

4、Inches mm Inches mm .005 0.08 .069 1.75 .130 3.30 .418 10.62 .685 17.40 .008 0.20 .071 1.80 .138 3.51 .424 10.77 .696 17.68 .010 0.25 .076 1.93 .144 3.66 .433 11.00 .700 17.78 .015 0.38 .078 1.98 .160 4.06 .480 12.19 .705 17.19 .018 0.46 .084 2.13 .195 4.95 .490 12.45 .708 17.98 .020 0.51 .089 2.26

5、.198 4.27 .515 13.08 .719 18.26 .022 0.56 .092 2.34 .204 5.18 .518 13.16 .728 18.49 .025 0.64 .093 2.36 .281 7.14 .530 13.46 .754 19.15 .032 0.81 .097 2.46 .290 7.37 .535 13.59 .769 19.53 .035 0.89 .098 2.49 .329 8.36 .558 14.17 .772 19.61 .042 1.07 .100 2.54 .340 8.64 .562 14.27 .774 19.66 .046 1.1

6、7 .101 2.57 .351 8.92 .580 14.70 .061 1.55 .106 2.69 .388 9.86 .594 15.09 .063 1.60 .112 2.84 .394 10.01 .627 15.93 .065 1.65 .125 3.18 .413 10.49 .636 16.15 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for information only. 3. Unless otherwise specified, tolerances are .005 (

7、0.13 mm) for three place decimals and .01 (0.25 mm) for two place decimals and 1 for all angles. 4. Coupling indicator line shall be color coded red. 5. Rear accessory interchangeability dimensions shall be in accordance with MIL-DTL-83723. 6. Shell size 8 will not mate with MIL-DTL-26500 connectors

8、. 7. Phantomed configuration optional. 8. See table I for contact cavities requiring this dimension. 9. The centerline of indicated projection must be located on vertical centerline 2. FIGURE 1. Classes A, G, K, M, R, T, W and Z - Continued. Provided by IHSNot for ResaleNo reproduction or networking

9、 permitted without license from IHS-,-,-MIL-DTL-83723/83E 4 FIGURE 2. Classes N and S. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83723/83E 5 Inches mm Inches mm Inches mm Inches mm Inches mm .005 0.08 .069 1.75 .130 3.30 .418 10.62 .685

10、 17.40 .008 0.20 .071 1.80 .138 3.51 .424 10.77 .696 17.68 .010 0.25 .076 1.93 .144 3.66 .433 11.00 .700 17.78 .015 0.38 .078 1.98 .160 4.06 .480 12.19 .705 17.19 .018 0.46 .084 2.13 .195 4.95 .490 12.45 .708 17.98 .020 0.51 .089 2.26 .198 4.27 .515 13.08 .719 18.26 .022 0.56 .092 2.34 .204 5.18 .51

11、8 13.16 .728 18.49 .025 0.64 .093 2.36 .281 7.14 .530 13.46 .754 19.15 .032 0.81 .097 2.46 .290 7.37 .535 13.59 .769 19.53 .035 0.89 .098 2.49 .329 8.36 .558 14.17 .772 19.61 .042 1.07 .100 2.54 .340 8.64 .562 14.27 .774 19.66 .046 1.17 .101 2.57 .351 8.92 .580 14.70 .061 1.55 .106 2.69 .388 9.86 .5

12、94 15.09 .063 1.60 .112 2.84 .394 10.01 .627 15.93 .065 1.65 .125 3.18 .413 10.49 .636 16.15 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for information only. 3. Unless otherwise specified, tolerances are .005 (0.13 mm) for three place decimals and .01 (0.25 mm) for two place

13、 decimals and 1 for all angles. 4. Coupling indicator line shall be color coded red. 5. Rear accessory interchangeability dimensions shall be in accordance with MIL-DTL-83723. 6. Shell size 8 will not mate with MIL-DTL-26500 connectors. 7. Phantomed configuration optional. 8. See table I for contact

14、 cavities requiring this dimension. 9. The centerline of indicated projection must be located on vertical centerline 2. FIGURE 2. Classes N and S Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83723/83E 6 Inches mm .116 2.95 .125

15、3.18 Shell size A thread coupling thread B max C D max F max 8 .562-24 UNEF-2A .394 .418 .413 .290 .562 10 .688-24 UNEF-2A .515 .535 .530 .388 .696 12 .875-20 UNEF-2A .685 .705 .700 .558 .875 14 .938-20 UNEF-2A .754 .774 .769 .627 .936 16 1.062-18 UNEF-2A .881 .901 .896 .772 1.062 18 1.188-18 UNEF-2

16、A .987 1.007 1.002 .860 1.187 20 1.312-18 UNEF-2A 1.112 1.132 1.127 .985 1.312 22 1.438-18 UNEF-2A 1.237 1.257 1.252 1.110 1.437 24 1.562-18 UNEF-2A 1.362 1.382 1.377 1.235 1.562 FIGURE 3. Dimensions and configurations. Provided by IHSNot for ResaleNo reproduction or networking permitted without lic

17、ense from IHS-,-,-MIL-DTL-83723/83E 7 Shell size G H R number of teeth S +.005 / -.000 T 8 .594 .812 12 .490 .076 .071 10 .719 .937 15 .636 .089 .084 12 .812 1.031 21 .806 14 .906 1.125 24 .875 16 .969 1.250 30 1.002 18 1.062 1.343 33 1.108 20 1.156 1.437 36 1.233 22 1.250 1.562 39 1.358 24 1.375 1.

18、703 42 1.483 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for information only. 3. Unless otherwise specified, tolerances are .005 (0.13 mm) for three place decimals and .01 (0.25 mm) for two place decimals and 1 for all angles. 4. Coupling indicator line shall be color coded

19、red. 5. Rear accessory interchangeability dimensions shall be in accordance with MIL-DTL-83723. 6. Shell size 8 will not mate with MIL-DTL-26500 connectors. 7. Phantomed configuration optional. 8. See table I for contact cavities requiring this dimension. 9. The centerline of indicated projection mu

20、st be located on vertical centerline 2. FIGURE 3. Dimensions and configurations - Continued. REQUIREMENTS: Dimensions and configurations: See figures 1 and 3 for classes A, G, K, M, R, T, W and Z. See figures 2 and 3 for classes N and S. This connector mates with MIL-DTL-83723/86, MIL-DTL-83723/91 a

21、nd MIL-DTL-83723/95 and MIL-C-83723/97. Insert arrangements and polarizing positions: See MIL-STD-1554 and table I. TABLE I. Insert arrangements requiring reduced diameter for raised seal barriers on outer row of contact cavities as indicated. Shell size Insert arrangements Contact cavities 8 10 03,

22、 98 06 1, 2, 3 1, 2, 3, 4, 5, 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83723/83E 8 O-ring: See MIL-DTL-83723. Part or Identifying Number (PIN) example: M83723/ 83 W 22 55 N Military designation Specification sheet number Class Shell

23、size Insert arrangement Polarizing position Changes from previous issue. Marginal notations are not used in this revision to identify changes with respect to the previous issue, due to the extent of the changes. Referenced documents. In addition to MIL-DTL-83723, this document references the followi

24、ng: MIL-STD-1554 MIL-DTL-26500 MIL-C-83723/97 MIL-DTL-83723/86 MIL-DTL-83723/91 MIL-DTL-83723/95 CONCLUDING MATERIAL Custodians: Preparing activity: Army - CR DLA - CC Navy - AS Air Force - 85 (Project 5935-2008-162) DLA - CC Review activities: Army - AR, MI Navy - EC Air Force - 19, 99 NOTE: The ac

25、tivities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-