DLA MIL-DTL-83723 93 D-2010 CONNECTORS ELECTRICAL (CIRCULAR ENVIRONMENT RESISTING) RECEPTACLE (SOLDER OR WELD FLANGE MOUNT BAYONET COUPLING STRAIGHT PIN CONTACT) (SERIES III CLASSE.pdf

1、 DETAIL SPECIFICATION SHEET CONNECTORS, ELECTRICAL, (CIRCULAR, ENVIRONMENT RESISTING), RECEPTACLE, (SOLDER OR WELD FLANGE MOUNT, BAYONET COUPLING, STRAIGHT PIN CONTACT), (SERIES III, CLASSES H AND Y) This specification is approved for use by all Departments and Agencies of the Department of Defense.

2、 The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-83723. FIGURE 1. Dimensions and configurations. AMSC N/A FSC 5935 INCH-POUND MIL-DTL-83723/93D 1 October 2010 SUPERSEDING MIL-DTL-83723/93C 23 May 2003 Provided by IHSNot for ResaleNo r

3、eproduction or networking permitted without license from IHS-,-,-MIL-DTL-83723/93D 2 FIGURE 1. Dimensions and configurations Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83723/93D 3 Shell size C D E F S +.005 -.000 V W FF GG 8 .

4、428 .433 .312 .536 .531 .561 .508 .500 .760 .720 .505 .515 .406 10 .530 .535 .388 .659 .654 .696 .636 .562 .860 .820 .567 .577 .443 12 .700 .705 .558 .829 .824 .875 .806 .750 1.065 1.025 .755 .765 .668 14 .769 .774 .627 .898 .893 .935 .875 .812 1.110 1.070 .817 .827 .668 16 .896 .901 .772 1.025 1.02

5、0 1.062 1.002 .937 1.230 1.190 .942 .952 .763 18 1.002 1.007 .860 1.131 1.126 1.187 1.108 1.062 1.360 1.320 1.067 1.077 .862 20 1.127 1.132 .985 1.256 1.251 1.312 1.233 1.187 1.450 1.410 1.192 1.202 1.108 22 1.252 1.257 1.110 1.381 1.376 1.437 1.358 1.312 1.610 1.570 1.317 1.327 1.204 24 1.377 1.382

6、 1.235 1.506 1.501 1.562 1.483 1.437 1.730 1.690 1.442 1.452 1.388 FIGURE 1. Dimensions and configurations Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83723/93D 4 Inches mm Inches mm Inches mm Inches mm .00005 0.001 .406 10.31

7、.769 19.53 1.131 28.73 .003 0.08 .428 10.87 .772 19.61 1.132 28.75 .004 0.10 .433 11.00 .774 19.66 1.187 30.15 .005 0.13 .443 11.25 .806 20.47 1.190 30.23 .015 0.38 .490 12.45 .812 20.62 1.192 30.28 .020 0.51 .500 12.70 .817 20.75 1.202 30.53 .032 0.81 .505 12.83 .820 20.83 1.204 30.58 .048 1.22 .50

8、8 12.90 .824 20.94 1.230 31.24 .062 1.57 .515 13.08 .827 21.01 1.235 31.37 .071 1.80 .530 13.46 .829 21.06 1.251 31.78 .076 1.93 .531 13.49 .860 21.84 1.252 31.80 .078 1.98 .535 13.59 .862 21.89 1.256 31.90 .084 2.13 .536 13.61 .875 22.23 1.257 31.93 .089 2.26 .540 13.71 .893 22.68 1.312 33.32 .090

9、2.29 .558 14.17 .896 22.76 1.317 33.45 .094 2.39 .560 14.22 .898 22.81 1.327 33.71 .097 2.46 .561 14.25 .901 22.89 1.358 34.49 .101 2.57 .562 14.27 .935 23.75 1.376 34.95 .106 2.69 .567 14.40 .937 23.80 1.377 34.98 .108 2.74 .577 14.66 .942 23.93 1.381 35.08 .112 2.84 .627 15.93 .952 24.18 1.382 35.

10、10 .138 3.51 .636 16.15 .985 25.02 1.388 35.26 .144 3.66 .654 16.61 1.002 25.45 1.410 35.81 .198 5.03 .659 16.74 1.007 25.58 1.422 36.12 .204 5.18 .668 16.97 1.020 25.91 1.437 36.50 .225 5.72 .696 17.68 1.025 26.04 1.450 36.83 .259 6.58 .700 17.78 1.062 26.97 1.452 36.88 .312 7.52 .705 17.91 1.065 2

11、7.05 1.483 37.67 .345 8.75 .720 18.29 1.067 27.10 1.501 38.13 .366 9.30 .734 18.64 1.070 27.18 1.506 38.25 .376 9.55 .750 19.05 1.077 27.36 1.562 39.67 .378 9.60 .755 19.18 1.108 28.14 1.570 39.88 .380 9.65 .760 19.30 1.110 28.19 1.610 40.89 .388 9.86 .763 19.38 1.126 28.60 1.690 42.93 .392 9.96 .76

12、5 19.43 1.127 28.63 1.730 43.94 FIGURE 1. Dimensions and configurations Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83723/93D 5 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for information only. 3. Unless

13、 otherwise specified, tolerances are .005 inches (0.13mm) for three place decimals, .01 inches (0.25mm) for two place decimals, and 1 for all angles. 4. Notes 5 through 10 applicable to contacts only. 5. Dimensions apply after plating. 6. Contact finish: Gold plate .000050 inch (0.00127 mm) minimum

14、in accordance with ASTM B488. A suitable underplating shall be used. Silver shall not be used. Finish is applied after sealing. 7. Surface finish: 63 ( ) all over in accordance with ASME-B46.1 unless otherwise specified. 8. Remove all burrs and sharp edges .003 to .005 inches (0.076 to 0.127 mm) R.

15、9. Diameters to be concentric within .004 inches (0.102 mm) TIR. 10. Diameters in the same cross-sectional plane to be concentric with each other within .003 inches (0.076 mm) TIR. 11. Three (3) pins to be located within .004 inches (0.102 mm) either side of (TP) relative to master polarizing keyway

16、. 12. See table I for contact cavities requiring these dimensions. FIGURE 1. Dimensions and configurations Continued. REQUIREMENTS Dimensions and configuration: See figure 1. This connector mates with MIL-DTL-83723/75 and /77. Insert arrangements and polarizing positions: See MIL-STD-1554 and table

17、I. TABLE I. Insert arrangements requiring reduced diameters for raised seal barriers on contact cavities as indicated. Shell size Insert arrangements Contact cavities 8 03, 98 1, 2, 3 10 06 1, 2, 3, 4, 5, 6 Connector accessories: See SAE-AS85049. Provided by IHSNot for ResaleNo reproduction or netwo

18、rking permitted without license from IHS-,-,-MIL-DTL-83723/93D 6 Part or Identifying Number (PIN) example: M83723/ 93 H 22 55 N Military designation Specification sheet number Class Shell size Insert arrangement Polarizing position Changes from previous issue. Marginal notations are not used in this

19、 revision to identify changes with respect to the previous issue due to the extent of the changes. Referenced documents. In addition to MIL-DTL-83723, this document references the following: MIL-DTL-83723/75 MIL-DTL-83723/77 MIL-STD-1554 ASME-B46.1 ASTM B488 SAE-AS85049 CONCLUDING MATERIAL Custodian

20、s: Preparing activity: Army CR DLA CC Navy AS Air Force 85 (Project 5935-2010-054) DLA CC Review activities: Army AR, MI Navy EC Air Force 19 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-