DLA MIL-DTL-83723 94 F-2010 CONNECTORS ELECTRICAL (CIRCULAR ENVIRONMENT RESISTING) RECEPTACLE (SINGLE HOLE MOUNT BAYONET COUPLING STRAIGHT PIN CONTACT) (SERIES III CLASSES H AND Y).pdf

1、 DETAIL SPECIFICATION SHEET CONNECTORS, ELECTRICAL, (CIRCULAR, ENVIRONMENT RESISTING), RECEPTACLE, (SINGLE HOLE MOUNT, BAYONET COUPLING, STRAIGHT PIN CONTACT), (SERIES III, CLASSES H, AND Y) This specification is approved for use by all Departments and Agencies of the Department of Defense. The requ

2、irements for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-83723. FIGURE 1. Dimensions and configurations. AMSC N/A FSC 5935 INCH-POUND MIL-DTL-83723/94F 1 October 2010 SUPERSEDING MIL-DTL-83723/94E 23 May 2003 Provided by IHSNot for ResaleNo reproducti

3、on or networking permitted without license from IHS-,-,-MIL-DTL-83723/94F 2 FIGURE 1. Dimensions and configurations Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83723/94F 3 Shell size B C D E F N thread S +.005 -.000 U 8 .137 .0

4、97 .428 .433 .312 .536 .531 .561 .625-20UN-2A .508 .670 10 .137 .097 .530 .535 .388 .659 .654 .696 .750-20UNEF-2A .636 .777 12 .137 .097 .700 .705 .558 .829 .824 .875 .9375-20UNEF-2A .806 .965 14 .137 .097 .769 .774 .627 .898 .893 .935 1.000-20UNEF-2A .875 1.090 16 .137 .097 .896 .901 .772 1.025 1.0

5、20 1.062 1.125-20UNEF-2A 1.002 1.215 18 .137 .097 1.002 1.007 .860 1.131 1.126 1.187 1.250-18UNEF-2A 1.108 1.340 20 .137 .097 1.127 1.132 .985 1.256 1.251 1.312 1.375-18UNEF-2A 1.233 1.465 22 .168 .128 1.252 1.257 1.110 1.381 1.376 1.437 1.500-18UNEF-2A 1.358 1.574 24 .168 .128 1.377 1.382 1.235 1.5

6、06 1.501 1.562 1.625-18UNEF-2A 1.483 1.699 FIGURE 1. Dimensions and configurations Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83723/94F 4 Shell size V M EE FF MM JJ 8 .984 .974 1.068 .605 .635 .493 .596 .590 10 1.109 1.099 1.1

7、92 .730 .760 .555 .721 .715 12 1.296 1.286 1.380 .917 .947 .743 .908 .902 14 1.396 1.386 1.505 .980 1.010 .805 .971 .965 16 1.521 1.511 1.630 1.105 1.135 .931 1.096 1.090 18 1.646 1.636 1.756 1.229 1.260 1.055 1.220 1.214 20 1.771 1.761 1.860 1.354 1.385 1.243 1.345 1.339 22 1.959 1.949 2.068 1.479

8、1.510 1.305 1.470 1.464 24 2.084 2.074 2.160 1.604 1.635 1.493 1.452 1.595 1.589 FIGURE 1. Dimensions and configurations Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83723/94F 5 Inches mm Inches mm Inches mm Inches mm Inches mm

9、.000050 0.0013 .089 2.26 .259 6.58 .558 14.17 1.589 40.36 .003 0.08 .090 2.29 .312 7.92 .560 14.22 1.595 40.51 .004 0.10 .093 2.36 .366 9.30 .561 14.25 1.604 40.74 .005 0.13 .094 2.39 .376 9.55 .590 14.99 1.630 41.40 .008 0.20 .097 2.46 .378 9.60 .596 15.14 1.635 41.53 .010 0.25 .098 2.49 .380 9.65

10、.605 15.37 1.636 41.55 .015 0.38 .101 2.57 .388 9.68 .627 15.93 1.646 41.81 .018 0.46 .106 2.69 .392 9.96 .635 16.13 1.699 43.15 .019 0.48 .112 2.84 .428 10.87 .636 16.15 1.752 44.50 .020 0.51 .128 3.25 .433 11.00 .654 16.61 1.756 44.60 .022 0.56 .137 3.48 .461 11.71 .659 16.74 1.761 44.98 .030 0.76

11、 .138 3.51 .481 12.22 .670 17.02 1.860 47.24 .032 0.81 .140 3.56 .490 12.45 .696 17.68 1.949 49.50 .050 1.27 .144 3.66 .493 12.52 .700 17.78 1.959 49.76 .054 1.37 .146 3.71 .530 13.46 .705 17.91 2.068 52.53 .068 1.73 .168 4.27 .531 13.49 .715 18.16 2.074 52.68 .071 1.80 .198 5.03 .535 13.59 .721 18.

12、31 2.084 52.93 .074 1.88 .204 5.18 .536 13.61 .730 18.54 2.160 54.86 .076 1.93 .225 5.72 .540 13.72 .743 18.87 .084 2.13 .250 6.35 .555 14.10 .760 19.30 .761 19.33 .980 24.89 1.187 30.15 1.376 34.95 .769 19.53 .984 24.99 1.192 30.28 1.377 34.98 .772 19.61 .985 25.02 1.214 30.84 1.380 35.05 .777 19.7

13、4 1.002 25.45 1.215 30.86 1.381 35.08 .781 19.84 1.007 25.54 1.220 30.99 1.382 35.10 .805 20.45 1.010 25.65 1.229 31.27 1.385 35.18 .824 20.93 1.020 25.91 1.233 31.31 1.386 35.20 .829 21.06 1.025 26.04 1.235 31.37 1.396 35.46 .860 21.84 1.055 26.80 1.243 31.57 1.437 36.20 .875 22.23 1.062 26.97 1.25

14、1 31.78 1.464 37.19 .893 22.68 1.068 27.13 1.252 31.80 1.465 37.21 .896 22.76 1.090 27.69 1.256 31.90 1.470 37.47 .898 22.81 1.096 27.84 1.257 31.93 1.479 37.57 .901 22.89 1.099 27.91 1.260 32.00 1.483 37.67 .902 22.91 1.105 28.07 1.286 32.66 1.493 37.92 .908 23.06 1.108 28.14 1.296 32.92 1.501 38.1

15、3 .917 23.29 1.109 28.17 1.305 33.15 1.505 38.23 .931 23.65 1.110 28.19 1.312 33.32 1.506 38.25 .935 23.75 1.126 28.60 1.339 34.01 1.510 38.35 .947 24.05 1.127 28.63 1.340 34.03 1.511 38.38 .965 24.51 1.131 28.73 1.345 34.16 1.521 38.63 .971 24.66 1.132 28.75 1.354 34.39 1.562 39.67 .974 24.74 1.135

16、 28.83 1.358 34.49 1.574 39.98 FIGURE 1. Dimensions and configurations Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83723/94F 6 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for information only. 3. Unless

17、otherwise specified, tolerances are .005 inches (0.13mm) for three place decimals, .01 inches (0.25mm) for two place decimals, and 1 for all angles. 4. Notes 5 through 10 applicable to contacts only. 5. Dimensions apply after plating. 6. Contact finish: Gold plate .000050 inch (0.00127 mm) minimum i

18、n accordance with ASTM B488. A suitable underplating shall be used. Silver shall not be used. Finish is applied after sealing. 7. Surface finish: 63 ( ) all over in accordance with ASME-B46.1 unless otherwise specified. 8. Remove all burrs and sharp edges .003 to .005 inches (0.076 to 0.127 mm) R. 9

19、. Diameters to be concentric within .004 inches (0.102 mm) TIR. 10. Diameters in the same cross-sectional plane to be concentric with each other within .003 (0.076 mm) TIR. 11. See table I for contact cavities requiring this dimension. FIGURE 1. Dimensions and configurations Continued. REQUIREMENTS

20、Dimensions and configurations: See figure 1. This connector mates with MIL-DTL-83723/75 and /77. Insert arrangements and polarizing positions: See MIL-STD-1554 and table I. TABLE I. Insert arrangements requiring reduced diameters for raised seal barriers on contact cavities as indicated. Shell size

21、Insert arrangements Contact cavities 8 03, 98 1, 2, 3 10 06 1, 2, 3, 4, 5, 6 Connector accessories: See SAE-AS85049. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83723/94F 7 Part or Identifying Number (PIN) example: M83723/ 94 H 22 55 N Mi

22、litary designation Specification sheet number Class Shell size Insert arrangement Polarizing position Changes from previous issue. Marginal notations are not used in this revision to identify changes with respect to the previous issue due to the extent of the changes. Referenced documents. In additi

23、on to MIL-DTL-83723, this document references the following: MIL-DTL-83723/75 MIL-DTL-83723/77 MIL-STD-1554 MS3186 ASME-B46.1 ASTM B488 SAE-AS85049 CONCLUDING MATERIAL Custodians: Preparing activity: Army CR DLA CC Navy AS Air Force 85 (Project 59352010-055) DLA CC Review activities: Army AR, AV, MI

24、 Navy EC Air Force 19, 99 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-