DLA MIL-DTL-83796 10-2008 HOSE ASSEMBLY RUBBER LIGHT WEIGHT INTERNAL SUPPORT COIL MEDIUM PRESSURE FIELD ATTACHABLE END FITTINGS FLARE TO FLARE《中压轻量橡胶软管总成 扩口到扩口内部支撑线圈可实地连接末端配件》.pdf

1、INCH-POUNDMIL-DTL-83796/10 11 August 2008 DETAIL SPECIFICATION SHEET HOSE ASSEMBLY, RUBBER, LIGHT WEIGHT, INTERNAL SUPPORT COIL, MEDIUM PRESSURE, FIELD ATTACHABLE END FITTINGS, FLARE TO FLARE This specification is approved for use by all Departments and Agencies of the Department of Defense. The req

2、uirements for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-83796. FIGURE 1. Hose assembly styles, field attachable fittings, flare-to-flare. AMSC N/A FSC 4720 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS

3、-,-,-MIL-DTL-83796/10 2 Hose assembly elbow fitting drop height. Elbow fitting drop height, A and B as shown on figure 2, are as specified in the applicable fitting specification sheet (see table I). TABLE I. Hose assembly, field attachable fittings, HCOF, styles A thru M. Fitting ends MIL-DTL-83798

4、 MIL-DTL-83797 hose cut off factor (HCOF) 1/ inches verses hose dash size number Style Fitting 1 Fitting 2 -03 -04 -05 -06 -08 -10 -12 -16 -20 -24 -32 A and B M83798/1 M83798/1 1.48 1.48 1.52 1.68 1.94 2.10 2.22 2.68 3.08 3.40 4.08 C and D M83798/1 M83798/2 1.68 1.81 1.90 2.06 2.28 2.49 2.83 3.37 3.

5、85 4.23 4.94 E and F M83798/1 M83798/3 1.53 1.68 1.74 1.91 2.12 2.32 2.70 3.27 3.77 4.17 4.90 G and H M83798/2 M83798/2 1.88 2.14 2.28 2.44 2.62 2.88 3.44 4.06 4.62 5.06 5.80 J and K M83798/2 M83798/3 1.73 2.01 2.12 2.29 2.48 2.71 3.31 3.96 4.54 5.00 5.78 L and M M83798/3 M83798/3 1.58 1.88 1.96 2.1

6、4 2.30 2.54 3.18 3.86 4.46 4.94 5.72 1/ Example of hose cut-off factor: for a -04, 1/4hose OD, 18-1/2 assembly length, style D, the bulk hose length = 18.50 - the HCOF = 18.50 -1.81 = 16.69. Bulk hose length required is 16.69. Hose assembly length. The hose assembly length is calculated as shown on

7、figure 2. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83796/10 3 NOTE: Length “L” to be measured between centers of nipple ends along a straight line parallel to hose length with hose laid out horizontally and straight. FIGURE 2. Hose ass

8、embly dimensions. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83796/10 4 Angular displacement. Angular displacement shall be as shown on figure 3. NOTES: 1. Angular displacement for hose assemblies with elbow fittings on both ends shall h

9、ave the angular displacement between elbows, measured counter-clockwise from the centerline of the nearest fitting, positioned at six-o clock, to the centerline of the other fitting (see SAE-J517). 2. The near end of the connector shall be put in numerical order relative to the far end (see table I)

10、. Example: Near end adapter 45, far end 90. 3. Angular displacement shall be measured in degrees with a tolerance of 3 for lengths up to 2 feet (61 cm) and 5 for all lengths over 2 feet (61 cm). 4. The angular displacement shall be expressed in two digits number of degrees divided. 5. Making the ang

11、ular determination in the wrong direction will result in an unacceptable part. FIGURE 3. Elbow fitting drop height and angular alignment. REQUIREMENTS Hose assemblies shall be specified on figures 1, 2, and 3. Fittings shall mate with parts in accordance with SAE-AS4395. Hose assembly length toleran

12、ce shall be in accordance with MIL-DTL-83796. Internal support coil. Internal support coil shall be in accordance Defense Supply Center Columbus drawing 08001. Support coil length. The support coil length shall be the overall hose assembly length minus the sum of the overall lengths of each end fitt

13、ing. Size codes shall be as specified in table II. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83796/10 5 TABLE II. Size code. 1/ 2/ Dash number -03 -04 -05 -06 -08 -10 -12 -16 Size code B E F G H J K M Inches fraction 3/16 1/4 5/16 3/8 1

14、/2 5/8 3/4 1 Inches decimal .188 .250 .313 .375 .500 .625 .750 1.000 Hose OD reference mm 4.78 6.35 7.95 9.53 12.70 15.88 19.05 25.40 Dash number -20 -24 -32 Size code N P R Inches fraction 1 1/4 1 1/2 2 Inches decimal 1.250 1.500 2.000 Hose OD reference mm 31.75 38.10 50.80 1/ Dimensions are in inc

15、hes. 2/ Metric equivalents are given for information only. Materials and finishes shall be in accordance with MIL-DTL-83796 and in table III. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83796/10 6 TABLE III. Nut and nipple material and fi

16、nish code. 1/ PIN code dash letter 2/ Material Plating Finish Steel (sizes -3, -4, and -5) Cadmium plating in accordance with SAE-AMS-C-81562, type II, class 3 or SAE-AMS-QQ-P-416, type II, class 2. Blank Aluminum (sizes -6 and above) Anodize in accordance with MIL-A-8625, type II -A Steel (sizes -3

17、, -4, and -5) Aluminum-nickel in accordance with ASTM F1136, grade 3, NC -B Aluminum (sizes -6 and above) Anodize above with NAVAIR trivalent chromium pretreatment (TCP) in accordance with MIL-DTL-81706, type 2, class A. -CN Steel (sizes -3, -4, and -5) Cadmium plating in accordance with SAE-AMS-C-8

18、1562, type II, class 3 or SAE-AMS-QQ-P-416, type II, class 2 with NAVAIR TCP in accordance with MIL-DTL-81706, type 2, class A. -H Steel (sizes -3, -4, and -5) Zinc phosphate finish in accordance MIL-DTL-16232 type Z, class1 3/ -J Steel (sizes -3, -4, and -5) Zinc plating in accordance with ASTM B63

19、3; type II or III, Fe/Zn 5, or ASTM B695, type II, class 5 N Steel (sizes -3, -4, and -5) NAVAIR TCP above. -R Steel (sizes -3, -4, and -5) Zinc plating in accordance with ASTM B633; type VI, Fe/Zn 5. -S Corrosion resistant steel No additional finish. Passivation in accordance with SAE-AMS2700, meth

20、od 2 -T Titanium (all sizes) Annealed -V Steel (sizes -3, -4, and -5) Zinc-nickel in accordance with SAE-AMS2417, type 1 -Z Zinc any type above PIN code F, G, H, J, R, V -ZN Zinc any type above PIN code F, G, H, J, R, V with NAVAIR TCP in accordance with MIL-DTL-81706, type 2, class A. 1/ Shall be c

21、apable of withstanding minimum of 96 hours salt spray. 2/ Part or Identifying Number (PIN). 3/ Hexavalent chromium free. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83796/10 7 PIN example: M83796 /10 H 08 2 F 06 TMaterial/finish (see tabl

22、e III) Angle between elbows to be specified in 5 increments, 30 / 5 = 06 (see figure 3)Style (see figure 1) Length in eighths of an inch (0 through 7) Length in inches (see figure 2) Size code (see table II) Specification sheet number Specification number M83796/10H082F06 indicates - Hose assembly f

23、or 1/2 hose OD., 8 1/4 inches in length, style F, 30 between elbows, titanium alloy. Referenced documents. In addition to MIL-DTL-83796, this document references the following: MIL-A-8625 MIL-DTL-16232 MIL-DTL-81706 MIL-DTL-83797 MIL-DTL-83798 08001 ASTM B633 ASTM B695 ASTM F1136 SAE-AMS2417 SAE-AS4

24、395 SAE-J517 SAE-AMS-C-81562 SAE-AMS-QQ-P-416 SAE-AMS2700 CONCLUDING MATERIAL Custodians: Preparing activity: Army - AV DLA - CC Navy - AS Air Force - 99 (Project 4720-2007-058) DLA - CC Review activities: Army - AT Navy - MC, SA Air Force - 71, 85 NOTE: The activities listed above were interested i

25、n this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-