DLA MIL-P-43907 D-1993 PARKA AND TROUSERS WET WEATHER.pdf

1、MIL-P-43907D = 9999906 1844332 113 1 I l t i I I I t I l l l l MIL-P-43907D 12 March 1993 SUPERSEDING 11 December 1987 MIL-P-43907C MILITARY SPECIFICATION PARKA AND TROUSERS, WET WEATHER This specification is approved for use by all Departments and Agencies of the Department of Defense. 1. SCOPE 1.1

2、 Scope. This document covers one type of a woodland camouflage polyurethane coated nylon wet weather parka and trousers. 1.2 Classification. The parka and trousers shall be of the following sizes as specified (see 6.2). Class 1 - Deleted (see 6.8) Class 2 - Woodland camouflage Schedule of sizes XX-S

3、ma 11 X-Sma 11 Sma 11 Medium Large X-Large Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document should be addressed to: Defense Personnel Support Center, Clothing and Textiles Directorate, Attn: DPSC-FSSD, 2800 South 20th S

4、treet, Philadelphia, PA 19101-8419, by using the Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter. AMSC N/A FSC 8405 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. Provided by IHSNot for ResaleNo reprod

5、uction or networking permitted without license from IHS-,-,-MIL-P-43907D 2. APPLICABLE DOCUMENTS 2.1 Government documents. 2.1.1 Documents. The following specifications, standards, and handbooks form a part this document to the extent specified herein. Unless otherwise specified, the issues of these

6、 documents are those listed in the issue of the Department of Defense Index of Specifications and Standards (DODISS) and supplement thereto, SPECIFICATIONS FEDERAL A-A- 5 O O 8 3 A-A-50 19 9 V-F-106 V-T-285 V-T-295 DDD-L-20 PPP-B-636 MILITARY MIL-B- 3 7 1 MIL-E-20652/1 MIL-F-21840 MIL-C-43303 MIL-T-

7、43566 MIL-C-43906 STANDARDS FEDERAL FED-STD-191 FED-STD-751 MILITARY MIL-STD-105 MIL-STD-129 MIL-STD-147 cited in the solicitation (see 6.2). - Bag, Plastic, Folded Garment - Thread, Polyester Core, Cotton-, or Polyester-Covered - Fasteners, Slide, Interlocking - Thread, Polyester - Thread, Nylon -

8、Label, For Clothing, Equipage, and - Boxes, Shipping, Fiberboard Tentage, (General Use) - Braid, Textile, Tubular - Eyelets, Metallic, Rolled Flange Type; - Fastener Tapes, Hook and Loop, - Cord, Elastic, Cotton - Tape, Textile, Cotton or Polyester, - Cloth, Coated, Nylon, Polyurethane and Eyelet Wa

9、sher Synthetic General Purpose, Natural or in Colors Double Coated - Textile Test Methods - Stitches, Seams, and Stitching - Sampling Procedures and Tables for - Marking for Shipment and Storage - Palletized Unit Loads Inspection by Attributes 2 Provided by IHSNot for ResaleNo reproduction or networ

10、king permitted without license from IHS-,-,-MIL-P-43907D 99999Ob I1844334 T9b (Unless otherwise indicated, copies of federal and military specifications, standards and handbooks are available from the Standardization Documents Order Desk, Bldg. 4D, 700 Robbins Avenue, Philadelphia, PA 19111-5094.) 2

11、.2 Non-Government Publications. The following documents form a part of this document to the extent specified herein. Unless otherwise specified, the issues of the documents which are DOD adopted shall be those listed in the issue of the DODISS specified in the solicitation. Unless otherwise specifie

12、d, the issues of documents not listed in the DODISS shall be the issues of the Nongovernment documents which are current on the date of r. i the solicitation. AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM) D 3951 - Standard Practice for Commercial Packaging (Applications for copies should be addr

13、essed to the American Society for Testing and Materials, 1916 Race Street, Philadelphia, PA 19103-1187.) (Non-Government standards and other publications are normally available from the organizations that prepare or distribute the documents. These documents also may be available in or through librar

14、ies or other informational services.) 2.3 Order of precedence. In the event of a conflict between the text of this document and the references cited herein, the text of this document shall take precedence. Nothing in this document, however, shall supersede applicable laws and regulations unless a sp

15、ecific exemption has been obtained. 3. REQUIREMENTS 3.1 Basic material. When specified (see 6.2), a sample shall be subjected to first article inspection (see 6.5) in accordance with 4.3. 3.2 Materials (see 6.4). 3.2.1 Basic material. The basic material for the parka and trousers shall conform to ty

16、pe II of MIL-C-43906. 3.2.2 Braids, drawcord. 3.2.2.1 Hood drawcord. The hood drawcord shall be flat cotton braid conforming to type VII, class 4, Camouflage Green 483 of MIL-B-371. The finished length shall be 44 1 inches. 3 Provided by IHSNot for ResaleNo reproduction or networking permitted witho

17、ut license from IHS-,-,-MIL-P-43907D 9999906 1844335 922 MIL-P-43907D 3.2.2.2 Trouser drawcord. The trouser drawcord shall be solid tubular cotton braid conforming to type IV or V, class 4, Camouflage Green 483 of MIL-B-371. The braid shall finish 5 inches longer than the circumference of the drawco

18、rd tunnel, measuring at waist from eyelet on right front to drawcord exit on left front, and from eyelet to eyelet on leg bottoms. 3.2.2.3 Parka drawcord. The parka waist drawcord shall be cotton elastic cord, conforming to class 2, Camouflage Green 483 of MIL-C-43303. The cord shall finish 5 inches

19、 longer than the circumference of the drawcord tunnel, measuring from drawcord exit on left side at bottom of parka to eyelet on right side. 3.2.2.4 Drawcord ends. The drawcord ends shall be tipped or impregnated to prevent raveling. The tipped or impregnated ends shall be at least 1/2 inch in lengt

20、h. 3.2.3 Tape. The tape for the trousers shall be 1/2 inch wide cotton tape, conforming to type I, class 4, Camouflage Green 483 Of MIL-T-43566. 3.2.4 Fastener tape, hook and loop. The fastener tape shall conform to type II, class 1, 5/8 inch and 1 inch wide of MIL-F-21840. The color shall be Camouf

21、lage Green 483. 3.2.5 Sizes subcla Thread. The thread for seaming and stitching shall be AA and B conforming to either types I or II, class 1, .ss B of V-T-285 or type I or II, class B of V-T-295 or A-A-50199, Ticket No. 50 with nonwicking finish may be substitute for sizes AA and B. The thread shal

22、l be dyed Camouflage Green 483. 3.2.5.1 Thread lubricant. When lubrication of the sewing thread is necessary, only water or isopropyl alcohol shall be used as a lubricant. 3.2.6 Fastener, slide, interlockinq. The slide fastener shall conform to type IV, style 8, size MS, continuous element polyester

23、 coil with long tab pull, (with hole large enough to accomodate a thong), 3/4 inch tape dyed Camouflage Green 483, of V-F-106. The lengths shall be as specified in 3.10. 3.2.6.1 Slide fastener thonq. The slide fastener thong shall be as specified in V-F-106, except that the finished length of thong

24、after assembly to the pull shall be 4 2 3/4 inches. 3.2.7 Eyelets and washers. The eyelets and washers for drawcord outlets shall be brass, black chemical finish. The eyelets shall conform to M20652/1-BBE 117 and the washers shall conform to M20652/1-BBW 101 Of MIL-E-20652/1. 4 Provided by IHSNot fo

25、r ResaleNo reproduction or networking permitted without license from IHS-,-,-I I I I I I I l. I l l l I I l I 3.2.8 Seam sealant tape. The seam tape used to seal the seams and allowable needle holes shall be cut in 1 inch (i 1/16 inch) wide strips of semi-clear tape fabricated in two layers as speci

26、fied below. The completed semi-clear tape shall be 0.006 inch (minimum) thickness and shall be capable of meeting a 5 pound (2.3 kg) minimum bonding strength. a. Adhesive or bottom layer shall be of 0.002 inch b. Barrier or top layer shall be of 0.004 inch (minimum) (minimum)thickness polyurethane a

27、dhesive. thickness high temperature resistant polyurethane carrier membrane. 3.2.8.1 Heat sealinq tape. Seams and stitching on outer shell, as indicated in 3.6.5.1, shall be sealed with heat sealing tape on the inner side of the parka and trousers. The entire width of the seam seal tape shall be hot

28、 air sealed over the seam or stitching. The tape shall be applied by blowing high temperature air on the thermoplastic tape adhesive, which is then driven through pressurized and sealing the seam and stitching. The machine shall operate on 1200 to 3600 watts, 115 or 200 vac air heater with pneumatic

29、ally activated driven rollers which press and tape onto the seam or stitching being sealed at a maximum of 20 feet per minute. All seam tapes shall be applied without tension and such that a minimum of 3/16 inch overlap is on both sides of the seam, except for the inside seam of the parka slide fast

30、ener closest to the chain shall be 1/8 inch minimum. All seam tapes shall overlap a minimum of 3/4 inch at joining parts. Sealed seams and end item shall be tested in accordance with 4.4.1.3 and 4.4.4. 3.2.9 Labels. Each parka and trousers shall have a combination identification-size label, an instr

31、uction label, and a care instruction label conforming to type IV of DDD-L-20. The fastness to crocking requirements of DDD-L-20 shall apply. 3.2.9.1 Combination identification-size label. The label shall conform to class 12. The label shall be located on the inside left front of the parka and the in

32、side right back of the trouser. 3.2.9.2 Instruction label. The instruction label shall conform to class 13. The label shall be located directly under the combination identification-size label. The body of the instructions shall be as follows: 5 Provided by IHSNot for ResaleNo reproduction or network

33、ing permitted without license from IHS-,-,-MIL-P-43907D W 0b 1844337 7T5 W MIL-P-43907D THESE GARMENTS ARE DESIGNED TO FIT OVER THE COLD WET UNIFORM. IN HOT WEATHER, IT MAY BE DESIRABLE TO USE SMALLER SIZED GARMENTS. SINCE AN IMPERMEABLE MATERIAL IS USED IN THE GARMENTS, CAUTION MUST BE TAKEN TO AVO

34、ID MOISTURE BUILD UP IN THE CLOTHING (INSULATION) WORN UNDERNEATH THE GARMENTS. MOISTURE BUILD UP MAY BE REDUCED IN TWO WAYS: BY ADJUSTING THE INNER CLOTHING WORN TO THE OUTDOOR TEMPERATURE AND THE ACTIVITY PLANNED AND ALSO BY UTILIZING THE CLOSURES TO PERMIT THE HEAT BUILD UP UNDER PARKA AND TROUSE

35、RS TO ESCAPE THEREBY REDUCING THE MOISTURE WITHIN THE INSULATING LAYERS. “CAUTION - IMPROPER USE OF THESE GARMENTS CAN PRODUCE HEAT EXHAUSTION WITHIN THIRTY MINUTES OF HARD WORK.“ 3.2.9.3 Care instruction label. The care instruction label shall conform to class 13. The label shall be located directl

36、y under the instruction label. CAUT I ON DO NOT MACHINE LAUNDER. DO NOT DRY CLEAN. HAND WASH IN WARM WATER AND MILD SOAP OR DETERGENT USING A SOFT BRISTLE BRUSH. RINSE THOROUGHLY AND AIR DRY. 3.3 Desiqn. The design of the parka and trousers shall be as shown in Figures 1 and 2, respectively. The hea

37、vily coated side of the cloth shall be on the outside of the parka and trousers. The parka shall have a hood with a drawcord at face opening and a slide fastener closure in the front. The trousers shall have a drawcord for waist adjustment and a drawcord at the bottom of each leg. 3.4 Fiqures. Figur

38、e 1 and 2 are furnished for information only. In the event of any inconsistencies between the figures and the written document, the written document shall control. 3.5 Patterns. Standard patterns, which provide an allowance of 1/2 inch for all seams, except where otherwise indicated, will be furnish

39、ed by the Government to the contractor for cutting working patterns. The working patterns shall be duplicates of the Government patterns. For the parkas, the contractor has the option of increasing the armhole area by 3/4 to 1-1/2 inches. 3.5.1 List of pattern parts. The pattern parts shall be cut f

40、rom material as specified and according to the number of parts listed in Table I. 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-t MIL-P-43907D M 99999Ob L8LiY338 b3L M MIL-P-43907D TABLE I. List of pattern parts. Materials Polyurethane double coa

41、ted nylon cloth Pattern nomenclature PARKA Hood Front, back and sleeve Pocket welt TROUSERS Front and back Pocket welt Cut parts 3.6.1 Stitches, seams, and stitchinq. Stitch, seam, and stitching types, specified in Table II shall conform to FED-STD-751. When two or more seam or stitch types are give

42、n for the same part of the operation, any one of them may be used. Where stitch type 401 is used, the looper (underthread) shall be on the inside of the garment. Seam allowances shall be maintained with seams sewn so that no raw edges, runoffs, twists, pleats, puckers or open seams will results. All

43、 seams shall start and finish evenly. Thread tension shall be maintained so that there will be no tight or loose stitching. Unless otherwise indicated, the gage of stitching for the double-lapped, double- stitched seams shall be 3/16 to 1/4 inch. 3.6.2 Thread breaks and ends of seams. Ends of all se

44、ams and stitching produced with 301 stitch type, when not caught in other seams or stitchings, shall be backtacked not less than 1/4 inch. Thread breaks in type 301 stitching shall be secured by stitching back of the break not less than 1 inch and thread breaks in type 401 stitching shall be oversti

45、tched not less than 1-1/2 inches at each break. Skipped stitches or thread breaks on 401 stitch type may be repaired by using 301 stitch type. 3.6.3 Stitches per inch. The minimum and maximum number of stitches per inch shall be as specified in Table II. 3.6.4 Caution. Care shall be taken during man

46、ufacturing operations (seaming, stitching and sealing) to insure that the coated cloth area adjacent to the seam is not damaged (see 6.3). 3.6.5 Sealinq of seams and stitchinq. I l 7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-P-V3907D 777770

47、b 1844337 578 D 3.6.5.1 Sealed areas. Both sides of the slide fastener tape stitching shall be sealed on the inside. Also, all crossover heat sealed taped seams and any tape ends not caught in turn in hem construction shall be separately sealed on a platen type heat sealer capable of applying pressu

48、re and controlling heat. option, if seam sealing machine is capable of securing tape ends, then a separate heat seal operation is not needed. The following areasd shall not be sealed. As an a. b. Unattached portion of pocket welt. (All other seamed c. Sleeve hem of parka. d. Drawcord tunnels at bott

49、om of parka, at trouser waist, e. Hook and pile tape stitching. f. Left and right fly stitching. Facing piece seam around the face opening of the hood. areas of pocket welt shall be sealed). and at bottom of trouser legs. 3.6.6 Sealed seam area performance requirements. 3.6.6.1 Hvdrostatic resistance. The sealed seams and the immediate adjacent area shall be subjected to the hydrostatic test specified in 4.4.4. Failure of the sealed seam area