DLA MIL-PRF-1 1232 E-2012 ELECTRON TUBE GAS SWITCHING TYPE 7166.pdf

1、 MIL-PRF-1/1232E 13 January 2012 SUPERSEDING MIL-E-1/1232D 2 July 1999 PERFORMANCE SPECIFICATION SHEET ELECTRON TUBE, GAS SWITCHING TYPE 7166 This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the electron tube describe

2、d herein shall consist of this document and the latest issue of MIL-PRF-1. DESCRIPTION: TR, frequency range 1,220 to 1,365 MHz, nominal peak power rating 1.5 Mw. ABSOLUTE RATINGS: Parameter: Unit: Incident power Mw Du - Ebb V dc Ii A dc Alt ft Maximum: Minimum: 2.0 - 0.001 - - -750 200 100 10,000 -

3、PHYSICAL CHARACTERISTICS: Dimensions: See figure 1. Mounting: See figure 2. 1/ Weight: 9 pounds (approximate). TEST CONDITIONS: Parameter: Unit: Incident power Mw tp1 s tp2 s prr pps Ii A dc F MHz Frequency Tolerance: 5% 0.15 0.15 - - - F MHz Test condition 1: Test condition 2: 0.50 2.00 4.0 4.0 1.0

4、 - 250 250 100 100 F3 F3 1 2 3 4 5 1,220 1,255 1,292 1,325 1,365 1% 1% 1% 1% 1% See footnotes at end of table I. GENERAL: Qualification: Not required Preproduction sample approval: Required. 2/ This specification sheet uses accept on zero defect sampling in accordance with MIL-PRF-1, table III. AMSC

5、 N/A FSC 5960 INCH-POUND Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-1/1232E 2 TABLE I. Testing and inspection. Method Limits Inspection MIL-STD-1311 Notes Test Conditions Symbol Min Max Unit Preproduction sample approval inspection Humid

6、ity 1011 - - - - - - Degradation due to vibration 4021 - - t = 1 hour - - - - Mechanical insertion - 1/ 3/ - - - - - Conformance inspection, part 1 Ignitor voltage drop 4406 - - - Ii = 100 A dc Eid 275 475 V dc Spike-leakage energy 4452 - 1 Ws - 0.25 erg Flat-leakage power 4452 - 1 pf - 75 mw Temper

7、ature cycling (nonoperating) 1027 - - - - - - Ignitor ignition time 4401 - - Ebb = -750 V dc; Ri = 4.5 Meg t - 5.0 sec Low-level VSWR 4473 4/ - F = (F1, F2, F3, F4, and F5) 0.1% - 1.3 - Arc loss 4488 - 1 La - 0.3 dB Conformance inspection, part 2 Dielectric material strain 4101 - - - - - - Insertion

8、 loss 4416 - - F = F3 5% Li - 0.5 dB Ignitor interaction 4421 - - Ii = 100 A dc Li - 0.2 dB Ignitor noise ratio 4460 - - Fo = 1,300 MHz; Ii = 100 A dc Nr - 1.3 - Recovery time 4471 - 2 t - 20 s See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted withou

9、t license from IHS-,-,-MIL-PRF-1/1232E 3 TABLE I. Testing and inspection - Continued. Method Limits Inspection MIL-STD-1311 Notes Test Conditions Symbol Min Max Unit Conformance inspection, part 3 Life test - 5/ 6/ 2 Group D; F = F3 3%; R = 2.5 Meg t 1,000 - hours Life-test end points: Spike-leakage

10、 energy Ignitor noise ratio Recovery time Ignitor voltage drop Insertion loss Arc loss Temperature cycling life test - 4452 4460 4471 4406 4416 4488 1027 - - - - - - - 1 - 2 - - 1 - Ii = 100 A dc Ii = 100 A dc 10 cycles Ws Nr t Eid Li La - - - - - - - - 0.50 1.5 25 550 0.7 0.3 - erg - s V dc dB dB -

11、 1/ A suitable gasket shall be bolted between the tube and the mounting seat. Tubes shall be supplied with gaskets at both ends. 2/ Preproduction sample approval requirements hereby replace any qualification requirements referable to the product covered herein. The term “First article testing“ shall

12、 be considered as synonymous with the term “Preproduction sample approval testing.“ All tests applicable herein (including all preproduction sample approval and conformance inspection, parts 1, 2, and 3) shall be performed during preproduction sample inspection. A failure of any one tube in any of t

13、he tests shall be cause for decision of preproduction sample disapproval. 3/ The tube shall be capable of being inserted and removed from its seat a minimum of 15 times with no deterioration in the tubes electrical characteristics. 4/ A swept frequency method may be used for this test. 5/ The TR tub

14、e will be terminated with a waveguide to type N transition (VSWR not to exceed 1.1:1 at test frequency) and a coaxial type N crystal mount connected to the transition. The mount will contain a type 1N21WE crystal which will be terminated by a dc ground return of 100 10 ohms. The crystal mount will h

15、ave a VSWR not to exceed 1.5 when tested with a microwave source at the test frequency which provides a crystal dc current between 0.3 ma to 1.5 ma in a 100 ohms termination. At the beginning of life test, the crystal noise figure (NF receiver) shall not exceed 7.0 dB under the standard 1N21WE test

16、conditions. The actual crystal noise figure at the beginning of life shall be recorded. 6/ The crystal noise figure degradation from the initial value shall not exceed 1.5 dB maximum. One crystal failure will be allowed during the life test. If a crystal failure occurs, a new crystal shall be insert

17、ed in the mount and the life test shall continue for a minimum of 100 hours. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-1/1232E 4 NOTE: This dimension shall conform to the requirements of MIL-PRF-3922/52A-001. FIGURE 1. Outline drawing o

18、f electron tube type 7166. Dimensions Ltr Inches Millimeters Min Max Min Max Conformance inspection, part 1 2/ J .240 .260 6.10 6.60 P .240 .260 6.10 6.60 Conformance inspection, part 1 4/ E See note F 5/16-18UNC-2A (10) holes G See note K .245 DIA .255 DIA 6.22 DIA 6.48 DIA L - 7.250 - 184.15 M .24

19、0 .260 6.10 6.60 N - 3.475 - 88.27 R Dr. size S-.348 (10) holes Dr. size S- 8.84 (10) holes T - 6.725 - 170.82 U 6.150 6.250 156.21 158.75 V .562 - 14.27 - Conformance inspection, part 2 A 4.618 4.634 117.30 117.70 B 2.492 2.508 63.30 63.70 C 2.367 2.383 60.12 60.53 D 3.930 3.946 99.82 100.23 H - 3.

20、3125 - 84.14 Q 4.105 4.125 104.27 104.78 S 7.355 7.375 186.82 187.33 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-1/1232E 5 FIGURE 2. Mounting seat. Dimensions Ltr Inches Millimeters Min Max Min Max N 2.309 2.317 58.65 58.85 P 1.246 1.254

21、31.65 31.85 R 2.371 2.379 60.22 60.43 W 3.934 3.942 99.92 100.13 Nominal A 5.437 138.10 B 4.000 101.60 C 2.000 50.80 D .600 15.24 E .2188 TYP 5.56 TYP F .080 2.03 G 4.135 105.03 H 2.067 52.50 J 3.537 89.84 K 1.768 44.91 L .2188 RAD x .270 DEEP TYP 5.56 RAD x 6.86 DEEP TYP M 8.6875 220.66 Q 5/16-18UN

22、C-2B (10) holes S 3.393 86.18 T 6.787 172.39 U 3.692 93.78 V 7.385 187.58 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-1/1232E 6 Referenced documents. In addition to MIL-PRF-1, this specification sheet references MIL-STD-1311. The margins

23、of this specification are marked with vertical lines to indicate where changes from the previous issue were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requ

24、irements of this document based on the entire content irrespective of the marginal notations and relationship to the last previous issue. Custodians: Preparing activity: Army - CR DLA - CC Navy - EC Air Force - 85 (Project 5960-2011-016) DLA - CC Review activities: Army - AR, MI Navy AS, CG, MC, OS,

25、 SH Air Force - 19, 99 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.daps.dla.mil/. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-