DLA MIL-PRF-1 1596B-1998 ELECTRON TUBE POWER TYPE 8116《电源型8116电子管》.pdf

1、 MIL-PRF-L/L59bB 0b 20b774 25Y I Parameter: Ef F Eb Unit: V ac MHz Vdc Maximum: 13.251265 30 1,000 AB, SSB fl 0% (Note 2) Test Conditions: 13.25126.5 - - - 600 Ecl Ec2 Ehk Ib IC1 Vdc Vdc Vdc mAdc mAdc -175 360 +lo0 220 10 -_ Adj 250 O 40 I INCHPOUND I MIL-PRF-l/1596B(NAVY) Parameter: Unit: Maximum:

2、AB, SSB (Note 2) Test Conditions: 11 Auqust 1998 SUPERSEDING Pgl Pg2 Pp Pi T tk W W W W “G (Note 3) sec (min) 2x1 7 2x30 200 30 120 _- -_ - _ - -_- MlL-E-l/1596A(NAVY) 30 October 1974 PERFORMANCE SPECIFICATION SHEET ELECTRON TUBE, POWER TYPE 8116 This specification is approved for use by Naval Elect

3、ronic Systems Command, Department of the Navy, and is available for use by all Departments and Agencies of the Department of Defense. The requirements for procuring the electron tube described herein shall consist of this document and the latest issue of Specification MIL-PRF-I. DESCRIPTION: Double

4、tetrode See figure 1 Mounting position - - - Vertical, base up or down; horizontal with anode pins in a horizontal plane. Weight - - - - - - - - - - 2.5 ounces nominal (70.9 grams) GENERAL Qualification - Not required AMSC N/A DISTRIBUTION STATEMENT A. Approved for pubic release; distribution is unl

5、imited. Page 1 of 8 FSC 5960 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-L/159bB I 9979906 20b7750 T7b I nspection %formance inspection t = 180 If = 13.25 V; t = 300 Ecl/lb = 1 O mA dc; Rp = 2,000 ohms Angle = 30“ Eb = 250 V dc; Ecl = -85

6、 V dc Paralleled operation class AB1 amplifier; Ef = 26.5 V ac; F = 15 MHz (rnax); Ecl/lb = 55 mA dc; lc2 = 30 mA dc (max) After 5 minutes, power output (1) Ef = 23.9 V ac; power output (1) Eb = 1,000 V dc; Ec2 = 270 V dc; Acceptance Level 1 .o 1 .o 1 .o 1 .o 1 .o 0.65 nspection -eve1 or ode II II I

7、I II II II jymbol IS IC2 EC1 IC1 If - Ec 1 Ib Po APO t APO Ef CgP Cin Gout - Limit Min - 1.5 -_ -25 - 760 - - -40 130 0.050 9.4 2.6 - - Limit Max - _- 6.0 -35 -6.0 1,260 - - 3,000 -52 10 -_ 10 15 0.080 11.8 3.7 - f Unit a mA dc V dc fi dc mA ac - mV ac V dc ClA dc W (usehil) YO YO PF PF PF See notes

8、 at end of Table I. 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-3/359bB E 9999906 2067753 902 nspection Conformance inspection. w Life test Lit-test end points: Peak emission Power output (1) Electrode current (grid) Vibration NOTES: 1.

9、 2. 3. 4. 5. 6. 7. 8. 9. 1 o. 11. Method Notes 3,8 11 MIL-PRF-1/15968( NAVY) Table 1. Testina and Inspection. -Continued. Conditions Group C; power output (1); t = 500 hours except: Ecl/lb = 50 mA dc; Ec2=250Vdc F = 50 Hz; t = 900; no voltages Acceptance Level -Ti- Symbol Limit Unit -_- a W (useful)

10、 fi dc _- This test is to be the first test performed at the conclusion of the holding period. Class AB linear RF amplifier single sideband suppressed carrier operation, both sections in parallel. Maximum glass and seal temperature shall be 250C. When operating the tube at maximum ratings, with forc

11、ed air cooling, it is necessary to cool both the lateral bulb surface as well as the anode pin seals by directing the flow of air toward the top and sides of the bulb. In most cases, approximately 20 cfm is sufficient. At reduced ratings, the use of heat sink is permissible. However, regardless of t

12、he type of cooling being used, the degree of cooling shall be determined by direct temperature measurement of both the seals and the bulb. Power output is total power at drive frequency delivered to load. Drive power is not subtracted from total output. Output circuit tuned for maximum power output.

13、 Read each unit separately. Grid (1) of section not under test shall be connected to -1 O0 V dc. Tie both anodes and the screen together. The pulse duration measured at 5 percent of the maximum value shall not be less than 3 p. At 50 percent amplitude, the duration shall be less than 2 YS. The appli

14、ed voltage shall have a maximum repetition rate such that the duty cycle, based on the pulse length measured at 50 percent amplitude, shall not exceed 0.0002 (0.02 percent). The test shall be duplicated on each unit separately. The unit not under test shall be tied to ground. Shielding shall be in a

15、ccordance with figure 2. Operation as class “AB1“ amplifier, Q = 10 minimum. Power output is total power at drive frequency delivered to load. Drive power is not subtracted from total output. Output circuit tuned for maximum power output. Drive to true “O“ bias point condition which shall be met aft

16、er all tuning is completed. Ef = 13.25, Eb = 800 V dc, Ec2 = 325 V dc, anodes and grids (1) in parallel, vary Ecl for Ib = 45 mA dc (total, both sections). These test conditions exceed the absolute maximum ratings and operation shall be limited to 5 minutes maximum “ony time followed by an “off“ tim

17、e of at least 5 minutes. Total “on“ time for power output (1) plus power output (2) tests shall be limited to 5 minutes with power output (3) test requiring as short a time as possible beyond the 5 minutes to reach stabilization. Vibration test shall be checked annually, using a sample of three tube

18、s with no failures allowed. In case of a sample failure, the test shall become a part of conformance inspection, part 2, for three consecutive successful submissions, at which time the test may revert to the conformance inspection, part 3 test. 3 Provided by IHSNot for ResaleNo reproduction or netwo

19、rking permitted without license from IHS-,-,-SEE MIL-PRF-L/L59bB I 9999906 2067752 849 MIL-PRF-1 Il 596B(NAVY) I ARROW ON TOP SEE NOTE 4 NOTE 3 c A L SEE NOTE 1 r-J / DIA 6 PLS I Dimensions in inches with metric I equivalents (mm) in parentheses Maximum I Notes Ltr I Minimum I Conformance inspection

20、, part 2 1 .O00 (25.40) 0.125 (3.18) M 52“ N 51 “ I Pin connections I 5 hct 6 7 h J FIGURE 1. Outline drawing of electron tube Woe 81 16. 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-1. 2. 3. 4. 5. NIL-PRF-L/L5bB I O6 2067753 785 MIL-PRF-l/1596B

21、(NAVY) NOTES: The axis Y- Y is defined as the axis of the base pin gage described in note 2. The tube base shall be capable of entering to a distance of 0.375 (9.53 mm) a flat plate gage having six holes 0.0800 (2.03 mm) kO.0005 (0.01 mm) and one hole 0.1450 (3.68 mm) 10.0005 (O.Olmm), all arranged

22、on a 1 .O000 (25.40mm) f0.0005 (0.1 mm) circle at the angles f5 specified on the outline. A 0.500 (12.70mm) fO.O1O (0.25mm) diameter hole at the center of the pin circle shall also be required. The axis Y - Y is defined by the center of this hole. The anode leads shall be capable of entering a flat

23、plate gage of 0.375 (9.53 mm) kO.001 (0.03 mm) thickness having two holes 0.2000 (5.08 mm) i0.0005 (0.01 mm) diameter spaced 0.365 (9.27 mm) 3.001 (0.03 mm) from a point coincident with the axis Y - Y. The axes of the holes shall be parallel to axis Y - Y and the plane of these axes shall be 90 degr

24、ees +-5 from the plane through axis Y - Y and pin No. 4. Location of large base pin shall be referenced by an arrow in the top stem. Tubes shall be inserted in jig shown on figure 3. Tubes that do not fit in the jig shall be rejected. FIGURE 1. Outline drawina of electron tube Woe 81 16 - Continued.

25、 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- MIL-PRF-L/15bB E 9999906 2067754 611 c SEE NOTE I- A =I / SEEA NOTE 5 SEE NOTE 3 1 C i NOTE 2 I Ltr I Dimensions in inches with metric I I equivalents (mm) in parentheses. 6.20) il -60) 6.35) I NOTE

26、S: I. 2. 3. 4. 5. 6. Ceptar tube socket (7 pin) (Johnson No. 122-101-100 or equivalent). Aluminum mounting box 6 (152.40 mm) x 4 (1 01.60 mm) x 3 (76.20 mm). Copper shielding, 0.040 (1 .O2 mm) thick x 0.750 (1 9.05 mm) wide. (May be hand formed to shape.) Female sockets for RF connectors (Amphenol S

27、O-239 or equivalent). Copper connection wire, AWG No. 20. Metric equivalents are in parentheses. FIGURE 2. Mountina box with 7 Din Septar socket, shieldina, and connection lead. 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MI L-PRF-1 Il 596B(NAV

28、Y) AmB E N DETAIL 1 t S PRESS FIT ON DETAIL2 J LTOOL STEEL HARDENED AND GRIND / -cy- TOOL STEEL HARDENED AND GRIND DETAIL 2 FIGURE 3. Outline gage for electron tube tvpe 81 16. 7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-I 999990b 2067756 494 I

29、 Dimension A INCHES 0.4891 M.0005 MM 12.42 M.O1 * B C D E F G H J K 0.4891 0.2192 0.0800 0.500 0.2192 0.4494 0.1039 0.3147 0.5000 10.0005 M.0005 t0.0005 DIA M.0005 M.O005 M.O005 t0.0005 ?r0.0005 12.42 5.57 2.03 12.70 5.57 11.41 2.64 7.99 12.70 IO.01 M.O1 ITo.01 +o. o 1 M.O1 kO.01 IT0.01 kO.01 DIA (6

30、 holes) ! M lL-PRF-1/15968( NAVY) Dimension L M N P R INCHES 0.3886 0.3886 0.1450 0.500 0.031 x 45O 10.0005 +-0.0005 +0.0005 -0.003 (Both sides) DIA +O.OOO MM 9.87 9.87 3.68 12.70 0.79 x 45“ M.O1 a.01 IO.01 -0.08 (Both sides) DIA +o.oo S T U V w 1.875 DIA 0.500 3.500 1.800 2.000 +0.003 +0.002 DIA -0

31、.000 -0.000 +0.08 +0.05 DIA -0.00 -0.00 47.63 DIA 12.70 88.90 45.72 50.80 NOTES: 1. 2. 3. Alternate method: May use standard drill bushing press fit in position. Pin circle to be concentric to 1.875 (47.63 mm) dia within 0.002 (0.05 mm) TIR. Dimension 1.875 (47.63 mrn) to be concentric to 1.800 (45.

32、72 mm) dia within 0.002 (0.05 rnm) TIR. FIGURE 3. Outline Page for electron tube twe 81 16. -Continued. Custodians: Navy - EC Review activities: Navy - AS, CG, MC, OS, SH Preparing activity: DLA - CC Project (5960-3434) 8 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-