DLA MIL-PRF-11693 7 F-2013 CAPACITORS FEED THROUGH RADIO-INTERFERENCE REDUCTION DC (HERMETICALLY SEALED IN METAL CASES) ESTABLISHED AND NON-ESTABLISHED RELIABILITY STYLES CZ23 CZ24.pdf

1、AMSC N/A FSC 5910 INCH-POUND MIL-PRF-11693/7F 29 March 2013 SUPERSEDING MIL-C-11693/7E 9 August 2001 PERFORMANCE SPECIFICATION SHEET CAPACITORS, FEED THROUGH, RADIO-INTERFERENCE REDUCTION, DC (HERMETICALLY SEALED IN METAL CASES) ESTABLISHED AND NON-ESTABLISHED RELIABILITY STYLES CZ23, CZ24, CZR23 AN

2、D CZR24 This specification sheet is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-PRF-11693 FIGURE 1. Styles CZ23, CZ24, CZR23 and CZR24 capacitors. Provided

3、 by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-11693/7F 2 Inches mm Inches mm Inches mm Inches mm .001 0.03 .05 1.3 .312 7.92 1.12 28.5 .002 0.05 .062 1.57 .400 10.16 1.38 35.1 .005 0.13 .109 2.77 .438 11.13 1.625 41.28 .015 0.38 .125 3.18 .562 14.2

4、7 1.88 47.8 .016 0.41 .234 5.94 .670 17.02 2.12 53.9 .020 0.51 .250 6.35 .75 19.1 2.38 60.5 .031 0.79 .255 6.48 .88 22.4 2.625 66.68 .040 1.02 .281 7.14 1.00 25.4 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only. 3. Unless otherwise specified, toleranc

5、e is .031 inch (0.79 mm). 4. Threaded neck to mounting shoulder shall be perpendicular with 3. 5. Recommended mounting torque: 10 pound-inches. 6. Lockwasher shall not be cadmium plated. FIGURE 1. Styles CZ23, CZ24, CZR23, and CZR24 capacitors - Continued. Provided by IHSNot for ResaleNo reproductio

6、n or networking permitted without license from IHS-,-,-MIL-PRF-11693/7F 3 REQUIREMENTS Dimensions and configuration: See figure 1 and table I. TABLE I. Type designation, dimensions, and electrical characteristics. Part or Identifying Number (PIN) 1/ Rated voltage (Volts, dc) Nominal capacitance (F)

7、Rated current (Amperes) Characteristics Dimensions (Inches) A .05 B .015 CZ-2-B-B473- 100 0.047 10 K, E .75 .400 CZ-2-B-B104- 100 0.1 10 K, E .88 .400 CZ-2-B-B224- 100 0.22 10 K, E 1.38 .400 CZ-2-B-B474- 100 0.47 10 K, E 1.38 .562 CZ-2-B-B105- 100 1.0 10 K, E 1.88 .670 CZ-2-B-B205- 100 2.0 10 K, E 2

8、.12 1.00 CZ-2-B-C473- 200 0.047 10 K, E .88 .400 CZ-2-B-C104- 200 0.1 10 K, E 1.12 .400 CZ-2-B-C224- 200 0.22 10 K, E 1.12 .562 CZ-2-B-C474- 200 0.47 10 K, E 1.88 .562 CZ-2-B-C105- 200 1.0 10 K, E 2.12 .750 CZ-2-B-E104- 400 0.1 10 K, E 1.12 .562 CZ-2-B-E224- 400 0.22 10 K, E 1.88 .562 CZ-2-B-E474- 4

9、00 0.47 10 K, E 2.12 .750 CZ-2-B-F472- 600 0.0047 10 K, E .75 .400 CZ-2-B-F103- 600 0.01 10 K, E .75 .400 CZ-2-B-F473- 600 0.047 10 K, E 1.38 .400 CZ-2-B-F104- 600 0.1 10 K, E 1.38 .562 CZ-2-B-F224- 600 0.22 10 K, E 1.88 .670 CZ-2-B-F474- 600 0.47 10 K, E 2.38 .750 1/ Complete PIN will include the f

10、ollowing: 1st dash - Symbol “R” (for styles CZR23 and CZR24) or dash will be deleted (for styles CZ23 and CZ24). 2nd dash - Applicable style number. 3rd dash - Applicable characteristic (K or E). 4th dash - Applicable failure rate level symbol (CZR23 and CZR24 only) or dash will be deleted (for styl

11、es CZ23 and CZ24). Dielectric: Normally paper, or paper-plastic. Characteristic: See table I. Temperature range: Characteristic E -55C to +85C. Characteristic K -55C to +125C. Rated voltage: See table I. Rated current: See table I. Capacitance: See table I. Provided by IHSNot for ResaleNo reproducti

12、on or networking permitted without license from IHS-,-,-MIL-PRF-11693/7F 4 Insertion loss: Measurements shall be made at the following frequencies for the capacitance values specified. Nominal capacitance (F) Frequency (MHz) 0.0047 400 and 1,000 0.01 400 and 1,000 0.047 400 and 1,000 0.1 400 and 200

13、 0.22 400 and 100 0.47 400 and 80 1.0 400 and 50 2.0 400 and 50 DC resistance: The dc resistance shall not exceed 0.01 ohm. Vibration, high frequency: Method 204 of MIL-STD-202 condition A (10G). Thermal shock: Method 107 of MIL-STD-202. IR at +25C: Not less than 30 percent of the value specified in

14、 the initial requirement. Capacitance: Change not more than 5 percent from the initial measurement. Moisture resistance: Method 106 of MIL-STD-202. IR at +25C: Not less than 30 percent of the initial requirement. Capacitance: Change not more than 5 percent from the initial measurement. Solderability

15、: Applicable for styles CZ23, CZ24, CZR23, and CZR24. Life (accelerated): Method 108 of MIL-STD-202. IR at +25C: Not less than 30 percent of the value specified in the initial requirement. Capacitance: Change not more than 5 percent from the initial measured value. Referenced documents: In addition

16、to MIL-PRF-11693, this document references MIL-STD-202. Changes from previous issue: The margins of this specification are marked with vertical lines to indicate where changes from the previous issue were made. This was done as a convenience only and the Government assumes no liability whatsoever fo

17、r any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations and relationship to the last previous issue. Custodians: Preparing activity: Army - CR DLA - CC Navy - EC Air

18、Force - 85 (Project 5910-2013-007) DLA - CC Review activities: Army - EA, MI Air Force 99 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.dla.mil/. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-