DLA MIL-PRF-15160 16 F-2011 FUSES INSTRUMENT POWER AND TELEPHONE (NONINDICATING) STYLE F16.pdf

1、AMSC N/A FSC 5920 INCH-POUND MIL-PRF-15160/16F 15 November 2011 SUPERSEDING MIL-PRF-15160/16E 7 July 2006 PERFORMANCE SPECIFICATION SHEET FUSES, INSTRUMENT, POWER, AND TELEPHONE (NONINDICATING), STYLE F16 This specification is approved for use by all Departments and Agencies of the Department of Def

2、ense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-PRF-15160. Ltr Inches mm Min Max Min Max A 2.969 3.031 75.41 76.99 B .804 .820 20.42 20.83 C .625 - 15.88 - NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for gene

3、ral information only. FIGURE 1. Style F16, characteristic A. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-15160/16F 2 Ltr Inches mm Min Max Min Max A 2.969 3.031 75.41 76.99 B .804 .820 20.42 20.83 C .625 - 15.88 - D - .130 - 3.30 E .085 -

4、 2.16 - F .172 .196 4.37 4.98 G - .123 - 3.12 H - .170 - 4.32 J .086 - 2.18 - K .026 .036 0.66 0.91 NOTES: 1. Dimensions are in inches. 2. The diameter of the rejection ferrule shall be within zero and minus .050 inch of the diameter of the main contact area. 3. The end of the ferrule shall be flat

5、with not greater than .015 inch concavity. FIGURE 2. Style F16, characteristic BR. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-15160/16F 3 REQUIREMENTS: Interface and physical dimensions: See figures 1 and 2. Case: Fiber or alternate mate

6、rial. (Alternate to fiber material (tube) shall have an average burst strength of 2,300 pounds per square inch with a value of not less than 1,300 pounds per square inch). Ferrule: Brass. Finish: Nickel, bright alloy, or bright dipped, silver plated when specified. Terminal strength: Method 211 of M

7、IL-STD-202, test condition E, 5 inch-pound torque between ferrules and fuse body. Electrical: Electrical requirements shall be as specified in table I. Shock: Method 207 of MIL-STD-202, HI shock. Vibration: Method 204 of MIL-STD-202, test condition A (except 5g peak). TABLE I Electrical requirements

8、. Characteristic A BR Voltage rating Overload test 1/ 135% 500% Short circuit test at 250 V dc at 250 V ac at 450 V rms ac 2/ 250 V ac 250 V dc 450 V rms ac 0 1 hour N/A 10,000A N/A 3,000A (50% PF max.) 3/ 250 V ac 250 V dc N/A 0 1 hour 10 25 seconds 10,000A 200,000A (20% PF max.) N/A 1/ Overload is

9、 shown as a percentage of the current rating of the fuse. 2/ Characteristic A fuses may be used for 450 V rms ac. 3/ Power factor (PF). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-15160/16F 4 Part or Identifying Number (PIN): The PIN shal

10、l be constructed from table II (e.g., F16A250V35A, or F16BR250V60A). TABLE II Part or Identifying Number. 1/ Style Characteristic Maximum voltage Current rating F16 A 250 V 35A F16 A 250 V 40A F16 A 250 V 45A F16 A 250 V 50A F16 A 250 V 60A F16 BR 2/ 250 V 35A F16 BR 2/ 250 V 40A F16 BR 2/ 250 V 45A

11、 F16 BR 2/ 250 V 50A F16 BR 2/ 250 V 60A 1/ For silver plated terminals, the designator “S” is added after the current rating. 2/ The characteristic B fuse has been discontinued. The characteristic BR fuse may be used to replace the old characteristic B fuse of the same current rating. VERIFICATION:

12、 Qualification inspections: The number of qualification samples required shall be: a. 24 samples maximum current rating of each voltage and design. b. 24 samples minimum current rating of each voltage and design. NOTE: If labels are used, five additional samples of any rating are required. Reference

13、d documents. In addition to MIL-PRF-15160, this document references the following: MIL-STD-202 The margins of this specification are marked with vertical lines to indicate where changes from the previous issue were made. This was done as a convenience only and the Government assumes no liability wha

14、tsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations and relationship to the last previous issue. Provided by IHSNot for ResaleNo reproduction or network

15、ing permitted without license from IHS-,-,-MIL-PRF-15160/16F 5 Custodians: Preparing activity: Army - CR DLA - CC Navy - SH Air Force - 85 (Project 5920-2011-075) DLA - CC Review activities: Army - AT, CR4, MI Navy - AS, CG, MC, OS Air Force - 19, 99 NOTE: The activities listed above were interested

16、 in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-