DLA MIL-PRF-15733 39 K-2009 FILTERS RADIO FREQUENCY INTERFERENCE HERMETICALLY SEALED STYLE FL91.pdf

1、 AMSC N/A FSC 5915 INCH-POUNDMIL-PRF-15733/39K 14 April 2009 SUPERSEDING MIL-PRF-15733/39J 27 February 2003 PERFORMANCE SPECIFICATION SHEET FILTERS, RADIO FREQUENCY INTERFERENCE, HERMETICALLY SEALED, STYLE FL91 * This specification sheet is approved for use by all Depart- ments and Agencies of the D

2、epartment of Defense. The complete requirements for acquiring the filters described herein shall consist of this specification sheet and MIL-PRF-15733. * PINs M15733/39-0007, -0008, -0011, -0013, are inactive for new design as of 19 August 1981. PINs M15733/39-0001, -0002, -0003, -0004, -0005, -0006

3、, -0010, -0016, -0017, and -0018 are inactive for new design after 14 April 2009. For new design, see table II for substitution data. FIGURE 1. Case dimensions and circuit diagrams. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-C D E F G H Dash num

4、ber A Max B Max Min Max Min Max Min Max Min Max Min Max Min Max J Max Maximum weight (grams) 0001 1/ .760 (19.30) .385 (9.78) .302 (7.67) .322 (8.18) .177 (4.50) .197 (5.00) .140 (3.56) .190 (4.83) .083 (2.11) .130 (3.30) .088 (2.24) .098 (2.49) .190 (4.83) .210 (5.33) .150 (3.81) 28.4 0002 1/ .760

5、(19.30) .385 (9.78) .302 (7.67) .322 (8.18) .177 (4.50) .197 (5.00) .140 (3.56) .190 (4.83) .083 (2.11) .130 (3.30) .088 (2.24) .098 (2.49) .190 (4.83) .210 (5.33) .150 (3.81) 28.4 0003 1/ .760 (19.30) .385 (9.78) .302 (7.67) .322 (8.18) .177 (4.50) .197 (5.00) .140 (3.56) .190 (4.83) .083 (2.11) .1

6、30 (3.30) .088 (2.24) .098 (2.49) .190 (4.83) .210 (5.33) .150 (3.81) 28.4 0004 1/ .760 (19.30) .385 (9.78) .302 (7.67) .322 (8.18) .177 (4.50) .197 (5.00) .140 (3.56) .190 (4.83) .083 (2.11) .130 (3.30) .088 (2.24) .098 (2.49) .190 (4.83) .210 (5.33) .150 (3.81) 28.4 0005 1/ .760 (19.30) .385 (9.78

7、) .302 (7.67) .322 (8.18) .177 (4.50) .197 (5.00) .140 (3.56) .190 (4.83) .083 (2.11) .130 (3.30) .088 (2.24) .098 (2.49) .190 (4.83) .210 (5.33) .150 (3.81) 28.4 0006 1/ .760 (19.30) .385 (9.78) .302 (7.67) .322 (8.18) .177 (4.50) .197 (5.00) .140 (3.56) .190 (4.83) .083 (2.11) .130 (3.30) .088 (2.

8、24) .098 (2.49) .190 (4.83) .210 (5.33) .150 (3.81) 28.4 0007 1/ .760 (19.30) .385 (9.78) .302 (7.67) .322 (8.18) .177 (4.50) .197 (5.00) .140 (3.56) .190 (4.83) .083 (2.11) .130 (3.30) .088 (2.24) .098 (2.49) .190 (4.83) .210 (5.33) .150 (3.81) 28.4 0008 1/ .760 (19.30) .385 (9.78) .302 (7.67) .322

9、 (8.18) .177 (4.50) .197 (5.00) .140 (3.56) .190 (4.83) .083 (2.11) .130 (3.30) .088 (2.24) .098 (2.49) .190 (4.83) .210 (5.33) .150 (3.81) 28.4 0009 .760 (19.30) .385 (9.78) .302 (7.67) .322 (8.18) .177 (4.50) .197 (5.00) .140 (3.56) .190 (4.83) .083 (2.11) .130 (3.30) .088 (2.24) .098 (2.49) .190

10、(4.83) .210 (5.33) .150 (3.81) 28.4 0010 1/ .760 (19.30) .385 (9.78) .302 (7.67) .322 (8.18) .177 (4.50) .197 (5.00) .140 (3.56) .190 (4.83) .083 (2.11) .130 (3.30) .088 (2.24) .098 (2.49) .190 (4.83) .210 (5.33) .150 (3.81) 28.4 0011 1/ .760 (19.30) .385 (9.78) .302 (7.67) .322 (8.18) .177 (4.50) .

11、197 (5.00) .140 (3.56) .190 (4.83) .083 (2.11) .130 (3.30) .088 (2.24) .098 (2.49) .190 (4.83) .210 (5.33) .150 (3.81) 28.4 0012 .760 (19.30) .385 (9.78) .302 (7.67) .322 (8.18) .177 (4.50) .197 (5.00) .140 (3.56) .190 (4.83) .083 (2.11) .130 (3.30) .088 (2.24) .098 (2.49) .190 (4.83) .210 (5.33) .1

12、50 (3.81) 28.4 0013 1/ .760 (19.30) .385 (9.78) .302 (7.67) .322 (8.18) .302 (7.67) .322 (8.18) - .190 (4.83) - .115 (2.92) .091 (2.31) .096 (2.44) .190 (4.83) .210 (5.33) .150 (3.81) 28.4 0014 .760 (19.30) .385 (9.78) .302 (7.67) .322 (8.18) .302 (7.67) .322 (8.18) - .190 (4.83) - .115 (2.92) .091

13、(2.31) .096 (2.44) .190 (4.83) .210 (5.33) .150 (3.81) 28.4 0015 .509 (12.93) .385 (9.78) .120 (3.05) .130 (3.30) .302 (7.67) .322 (8.18) - .190 (4.83) - .115 (2.92) - 1.50 (3.81) .190 (4.83) .210 (5.33) - 28.4 0016 1/ .80 (20.3) .416 (10.57) - - .180 (4.57) .200 (5.08) - .357 (9.07) .099 (2.51) .11

14、9 (3.02) - - .190 (4.83) .210 (5.33) - 10.0 0017 1/ .80 (20.3) .416 (10.57) - - .180 (4.57) .200 (5.08) - .357 (9.07) .099 (2.51) .119 (3.02) - - .190 (4.83) .210 (5.33) - 10.0 0018 1/ .80 (20.3) .416 (10.57) - - .180 (4.57) .200 (5.08) - .357 (9.07) .099 (2.51) .119 (3.02) - - .190 (4.83) .210 (5.3

15、3) - 10.0 MIL-PRF-15733/39K 2 1/ Inactive for new design. FIGURE 1. Case dimensions and circuit diagrams - Continued.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-15733/39K 3 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are in

16、parentheses. 3. Metric equivalents are given for general information only. 4. Circuit diagram is for information only. 5. Filters shall be supplied with mounting hardware. 6. Terminal identification (nonsymmetrical filters): The case shall be marked at the threaded end of the filter, with the symbol

17、 “C” or the symbol “L”, as follows: Circuit Symbol L1C L2L 7. Recommended mounting torque: 48 in-oz. FIGURE 1. Case dimensions and circuit diagrams Continued.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-* TABLE I. Electrical characteristics. Rated

18、 Minimum insertion loss (dB) in accordance with MIL-STD-220 1/ AT +25C AT -55C and +125C voltage (volts dc) Circuit diagram Max current (amps) Max voltage drop (volts) Capacitance F GMV 30 100 kHz 150 kHz kHz 300 kHz 1 MHz 10 MHz 100 MHz 1 GHz 30 kHz 100 kHz 150 kHz 300 kHz 1 MHz 10 MHz 100 MHz 1 GH

19、z Dash number 100 L1 .5 1.0 .66 6 - 28 40 60 60 60 70 4 - 26 38 58 58 60 70 0001 2/ 100 L2.5 1.0 .66 6 - 28 40 60 60 60 70 4 - 26 38 58 58 60 70 0002 2/ 100 L1 1.0 .25 .45 6 - 20 30 50 60 60 70 4 - 18 28 48 58 60 70 0003 2/ 100 L2 1.0 .25 .45 6 - 20 30 50 60 60 70 4 - 18 28 48 58 60 70 0004 2/ 100 L

20、12.0 .14 .45 6 - 20 26 40 60 60 70 4 - 18 24 38 58 60 70 0005 2/ 100 L2 2.0 .14 .45 6 - 20 26 40 60 60 70 4 - 18 24 38 58 60 70 0006 2/ 100 L1 5.0 .075 .45 6 - 20 26 35 60 60 70 4 - 18 24 33 58 60 70 0007 2/ 100 L2 5.0 .075 .45 6 - 20 26 35 60 60 70 4 - 18 24 33 58 60 70 0008 2/ 100 L1 10.0 .03 .45

21、6 - 20 26 35 56 60 70 4 - 18 24 33 54 60 70 0009 100 L2 10.0 .03 .45 6 - 20 26 35 56 60 70 4 - 18 24 33 54 60 70 0010 2/ 100 Pi 10.0 .03 .99 9 - 24 29 40 70 70 70 7 - 22 27 38 68 70 70 0011 2/ 100 Pi 10.0 .03 .99 9 - 24 29 40 70 70 70 7 - 22 27 38 68 70 70 0012 100 Pi 10.0 .03 1.5 9 - 24 29 40 70 70

22、 70 7 - 22 27 38 68 70 70 0015 100 Pi .25 .38 1.5 - 58 - 76 80 80 80 80 - 56 - 74 78 78 80 80 0016 2/ 100 Pi 3.0 .18 1.5 - 14 - 41 76 80 80 80 - 12 - 39 74 78 80 80 0017 2/ 100 Pi 5.0 .20 1.5 - - - 28 68 80 80 80 - - - 26 66 78 80 80 0018 2/ 50 L2 10.0 .03 1.4 14 - 28 34 44 52 70 70 12 - 26 32 42 50

23、 70 70 0013 2/ 50 L1 10.0 .03 1.4 14 - 28 34 44 52 70 70 12 - 26 32 42 50 70 70 0014 MIL-PRF-15733/39K 4 1/ Insertion loss measurements shall be made under full load over the frequency range of 100 kHz to 10 MHz. Insertion loss measurements above or below this frequency range shall be made under no

24、load. 2/ Inactive for new design.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-15733/39K 5 REQUIREMENTS: Dimensions and configuration: See figure 1. Weight: See figure 1. Case: Metal. * Case and mounting hardware finish: In accordance with

25、MIL-PRF-15733. Pure tin finish is prohibited as specified in MIL-PRF-15733. Seal: Metal-to-glass. Terminals: Solderable. Operating temperature range: -55C to +125C. Rated voltage: See table I. Rated current: See table I. Insertion loss: In accordance with MIL-PRF-15733 and table I. Seal: In accordan

26、ce with MIL-PRF-15733. Capacitance to ground: In accordance with MIL-PRF-15733 and table I. Dissipation factor: 3.0 percent maximum. Temperature rise: 25C, maximum. Barometric pressure (reduced): In accordance with MIL-PRF-15733 and method 105, MIL-STD-202, test condition D (100,000 ft) for -0001 th

27、rough -0010; Test condition C (70,000 ft) for -0011 through -0015; and test condition B (50,000 ft) for -0016 through -0018. Insulation resistance: In accordance with MIL-PRF-15733 and the following: At 25C the insulation resistance shall not be less than 1000 megohms. At +125C the insulation resist

28、ance shall not be less than 100 megohms. Voltage drop: See table I. Terminal strength: In accordance with MIL-PRF15733 and method 211, MIL-STD-202; test condition A (pull). Force: 5 pounds. Salt atmosphere (corrosion): In accordance with MIL-PRF-15733 and method 101, MIL-STD-202; test condition A. S

29、hock (specified pulse): In accordance with MIL-PRF-15733 and method 213, MIL-STD-202. The following details apply: Test condition I: (-0001 through -0014 and -0016 through -0018). Test condition A: (-0015). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS

30、-,-,-MIL-PRF-15733/39K 6 Vibration, high frequency: In accordance with MIL-PRF-15733 and method 204, MIL-STD-202; test condition D (20G). The following detail shall apply: Temperature conditioning: Prior to vibration, filters shall be heated in an oven to +125C plus one-half the temperature rise. Vi

31、bration in each plane shall begin within 5 minutes after removal of filters from the oven. Life: In accordance with MIL-PRF-15733 and method 108, MIL-STD-202; test condition D (1,000 hrs) for qualification; test condition B (250 hrs) for group C inspection. Part or Identifying Number (PIN): M15733/3

32、9-(dash number from table I). Extension of qualification: Qualification testing and approval to M15733/39-0014 shall be sufficient to grant qualification approval to M15733/39-0013 and M15733/39-0014. Qualification testing and approval to M15733/39-0012 and M15733/39-0016 shall be sufficient to gran

33、t qualification approval to M15733/39-0001 through -0012 and M15733/39-0015 through -0018. * TABLE II. Substitution data. For new design use Inactive PIN Superseding specification Superseding PIN M15733/39-0001 M15733/39-0002 M15733/39-0003 M15733/39-0004 M15733/39-0005 M15733/39-0006 M15733/39-0007

34、 M15733/39-0008 M15733/39-0010 M15733/39-0011 M15733/39-0013 M15733/39-0016 M15733/39-0017 M15733/39-0018 MIL-PRF-28861/3 MIL-PRF-28861/3 MIL-PRF-28861/2 MIL-PRF-28861/2 MIL-PRF-28861/2 MIL-PRF-28861/2 MIL-PRF-28861/2 MIL-PRF-28861/2 MIL-PRF-28861/1 MIL-PRF-15733/39 MIL-PRF-28861/1 MIL-PRF-28861/2 M

35、IL-PRF-28861/2 MIL-PRF-28861/2 M28861/03-007TB M28861/03-008TB M28861/02-004TB M28861/02-005TB M28861/02-007TB M28861/02-008TB M28861/02-010TB M28861/02-011TB M28861/01-005TB M15733/39-0012 M28861/01-001TB M28861/02-003TB M28861/02-009TB M28861/02-012TB NOTES: * Referenced documents. In addition to

36、MIL-PRF-15733, this specification sheet references the following documents: MIL-PRF-28861/1 MIL-PRF-28861/2 MIL-PRF-28861/3 MIL-STD-202 MIL-STD-220 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-15733/39K 7 Changes from previous issue: The m

37、argins of this specification sheet are marked with asterisks to indicate where changes from the previous issue were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate

38、the requirements of this document based on the entire content irrespective of the marginal notations and relationship to the last previous issue. Custodians: Preparing activity: Army - CR DLA - CC Navy - EC Air Force - 85 (Project 5915-2009-003) DLA - CC Review activities: Army - AT, AV Navy - AS, C

39、G, MC, OS, SH Air Force 99 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-