DLA MIL-PRF-15733 40 C (1)-2008 FILTERS RADIO INTERFERENCE STYLE FL35.pdf

1、 AMSC N/A FSC 5915 MIL-PRF-15733/40C W/AMENDMENT 1 21 April 2008 SUPERSEDING MIL-PRF-15733/40C 31 July 2003 PERFORMANCE SPECIFICATION SHEET FILTERS, RADIO INTERFERENCE, STYLE FL35 This specification sheet is approved for use by all Depart- ments and Agencies of the Department of Defense. The require

2、ments for acquiring the filters described herein shall consist of this specification sheet and MIL-PRF-15733. FIGURE 1. Dimensions and configuration. INCH-POUND Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-15733/40C W/AMENDMENT 1 2 A B C D

3、 E F G H Dash No. Min Max Min Max Min Max Min Max Min Max Max Min Max .015 0001 .375 (9.53) 437 (11.10) .656 (16.66) .718 (18.21) 469 (11.86) .531 (13.49) .187 (4.75) .249 (6.32) .172 (4.37) .202 (5.13) .234 (5.94) .281 (7.14) .343 (8.71) .093 (2.36) NOTES: 1. Dimensions are in inches. 2. Metric equ

4、ivalents are given for general information only. 3. Circuit diagram for information only. FIGURE 1. Dimensions and configuration (continued) REQUIREMENTS: Configuration and dimensions: See figure I. Weight: 2.7 grams maximum. Case: Not applicable (metallic mounting eyelet). * Terminals: Solderable (

5、see figure 1). Pure tin finish is prohibited (see MIL-PRF-15733). Operating temperature range: -55C to +125C. Rated voltage: 500 V dc or 350 V rms to 400 Hz, over the operating temperature range. Rated current: 25 amperes, dc or ac (rms). Insertion loss: In accordance with MIL-PRF-15733 and table I.

6、 Seal: Not applicable. Capacitance to ground: In accordance with MIL-PRF-15733. Measured capacitance shall be at least 3,000 pF. Temperature rise: +25C, maximum. Dielectric withstanding voltage: In accordance with MIL-PRF-15733. The following exception shall apply: Test voltage: 1,500 V dc applied f

7、or 1 to 5 seconds. Barometric pressure (reduced): In accordance with MIL-PRF-15733 and Method 105, MIL-STD-202; test condition D. Insulation resistance: In accordance with MIL-PRF-15733. Insulation resistance measured at 25C between either terminal and the case shall be at least 10 G ohms. Voltage d

8、rop: Not applicable. Overload: In accordance with MIL-PRF-15733. The following exception shall apply: * Measurements at +25C after test: Insulation resistance only shall be measured and shall meet initial requirements. Provided by IHSNot for ResaleNo reproduction or networking permitted without lice

9、nse from IHS-,-,-MIL-PRF-15733/40C W/AMENDMENT 1 3 Terminal strength: In accordance with MIL-PRF-15733 and Method 211, MIL-STD-202; test condition A. Applied force: 5 pounds. Salt atmosphere (corrosion): Not applicable. Thermal shock: Not applicable. Immersion: Not applicable. Shock (specified pulse

10、): In accordance with MIL-PRF-15733 and Method 213, MIL-STD-202; test condition I. Vibration, high frequency: In accordance with MIL-PRF-15733 and Method 204, MIL-STD-202; test condition D. Moisture resistance: In accordance with MIL-PRF-15733. The following exceptions shall apply: Polarization volt

11、age: Not applicable. Loading voltage: Not applicable. Measurements after 24-hour drying period, at a temperature not to exceed +85C, and a relative humidity of 50 percent. Insulation resistance shall be not less than 1 G ohm. Life: In accordance with MIL-PRF-15733 and Method 108, MIL-STD-202; test c

12、ondition B. The following exception shall apply: Measurements after test: Insulation resistance shall be not less than 1 G ohm. Marking: Filters shall not be marked. Full marking, in accordance with MIL-PRF-15733, shall be marked on the unit package. Part or Identifying Number (PIN): M15733/40- (das

13、h number from table I). TABLE I. Insertion loss versus frequency. Minimum no-load insertion loss (dB) in accordance with MIL-STD-220, at +25C Dash number 50 MHz 100 MHz 200 MHz 500 MHz 1-10 GHz 0001 40 55 65 70 70 * Referenced documents. In addition to MIL-PRF-15733, this document also references th

14、e following: MIL-STD-202 MIL-STD-220 * Changes from previous issue. The margins of this specification sheet are marked with asterisks to indicate where changes from the previous issue were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuraci

15、es in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations and relationship to the last previous issue. Provided by IHSNot for ResaleNo reproduction or networking permitted without lice

16、nse from IHS-,-,-MIL-PRF-15733/40C W/AMENDMENT 1 4 Custodians: Preparing activity: Army - CR DLA - CC Navy - EC Air Force - 11 (Project 5915-2008-013) DLA - CC Review activities: Army AT, AV Navy - AS, MC, OS, SH Air Force - 19, 99 * NOTE: The activities listed above were interested in this document

17、 as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-