DLA MIL-PRF-15733 51 F (1)-2008 FILTERS RADIO FREQUENCY INTERFERENCE STYLE FL48.pdf

1、 AMSC N/A FSC 5915 MIL-PRF-15733/51F W/AMENDMENT 1 21 April 2008 SUPERSEDING MIL-PRF-15733/51F 31 July 2003 PERFORMANCE SPECIFICATION SHEET FILTERS, RADIO FREQUENCY INTERFERENCE, STYLE FL48 This specification sheet is approved for use by all Depart- ments and Agencies of the Department of Defense. T

2、he requirements for acquiring the filters described herein shall consist of this specification sheet and MIL-PRF-15733. FIGURE 1. Dimensions and configuration. INCH-POUND Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A B C D E F G Dash number Min M

3、ax Min Max Min Max Min Max Min Max Min Max Min Max 0001 .219 (5.56) .281 (7.14) .375 (9.52) .437 (11.10) .125 (3.18) .187 (4.75) .281 (7.14) .343 (8.71) .135 (3.43) .150 (3.81) .105 (2.67) .140 (3.56) .185 (4.70) .205 (5.21) 0002 .204 (5.18) .249 (5.94) .749 (19.02) .811 (20.60) .141 (3.58) .186 (4.

4、34) .281 (7.14) .343 (8.71) .130 (3.30) .160 (4.06) N/A N/A .188 (4.78) .218 (5.54) NOTES: 1. Dimensions are in inches. 2. Metric equivalents are in parentheses and are given for information only. 3. Circuit diagram is for information only. 4. Leads shall be solid, solder-coated, AWG 20, .032 (0.81m

5、m) diameter. 5. Suggested mounting hole diameter: .160 (4.06mm). FIGURE 1 Dimensions and configuration (continued). TABLE I. Electrical characteristics. 1/ Minimum insertion loss (db) in accordance with MIL-STD-220, at +25C -55C and maximum operating temperature Dash no. Operating temperature range

6、Rated voltage (volts) Weight max (grams) Capacitance min (pF) 5 MHz 10 MHz 20 MHz 100 MHz 1 GHz 10 GHz 5 MHz 10 MHz 20 MHz 100 MHz 10 GHz 0001 -55C to +85C 200 V dc 200 V rms .8 5,500 - 15 21 55 70 70 - 3 8 40 70 0002 -55C to +125C 70 V dc .8 22,000 20 25 20 70 70 70 5 10 5 65 70 1/ Insertion loss m

7、easurements shall be performed at full-load from 5 MHz to 20 MHz and at no-load above 20 MHz. MIL-PRF-15733/51F W/AMENDMENT 12 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-15733/51F W/AMENDMENT 1 3 REQUIREMENTS: Dimensions and configuratio

8、n: See figure 1. Case: Not applicable (metallic mounting eyelet). Terminals: Solderable. Pure tin finish is prohibited. Operating temperature range: See table I. Rated voltage: See table I. Rated current: 10 amperes, dc or ac (rms). Insertion loss: In accordance with MIL-PRF-15733 and table I. Seal:

9、 Not applicable. Capacitance to ground: In accordance with MIL-PRF-15733. Measured capacitance shall be in accordance with table I. Temperature rise: +25C, maximum. Insulation resistance: In accordance with MIL-PRF-15733. The following detail and exception shall apply: Test potential: Rated dc volta

10、ge. Insulation resistance measured at 25C between either terminal and the case shall be at least 20,000 megohms. Voltage drop: Not applicable. Overload: In accordance with MIL-PRF-15733. The following exception shall apply: Measurements at +25C after test: Insulation resistance only shall be measure

11、d and shall meet initial requirements. Terminal strength: In accordance with MIL-PRF-15733 and Method 211, MIL-STD-202; test condition A. Applied force: 5 pounds. Salt atmosphere (corrosion): Not applicable. Thermal shock: Not applicable. Immersion: Not applicable. Shock (specified pulse): In accord

12、ance with MIL-PRF-15733 and Method 213, MIL-STD-202; test condition I. Vibration, high frequency: In accordance with MIL-PRF-15733 and Method 204, MIL-STD-202; test condition D. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-15733/51F W/AMEN

13、DMENT 1 4 Moisture resistance: In accordance with MIL-PRF-15733. The following details and exceptions shall apply: Polarization voltage: Not applicable. Loading voltage: Not applicable. Measurements after 24-hour drying period, at a temperature not to exceed +85C (dash number 0001) or +125C (dash nu

14、mber 0002), and a relative humidity of 50 percent: Insulation resistance shall be not less than 1 gigohm. Life: In accordance with MIL-PRF-15733 and Method 108, MIL-STD-202; test condition D. The following exception shall apply: Measurements after test: Insulation resistance shall be not less than 5

15、,000 megohms. Solderability: In accordance with MIL-PRF-15733 for both terminals and mounting termination. Marking: Filters shall not be marked. Full marking, in accordance with MIL-PRF-15733, shall be marked on the unit package. Part or Identifying Number (PIN): M15733/51- (dash number from table I

16、). Changes from previous issue. Marginal notations are not used in this revision to identify changes with respect to the previous issue due to the extensiveness of the changes. * Referenced documents. In addition to MIL-PRF-15733, this document also references the following: MIL-STD-202 MIL-STD-220

17、* Changes from previous issue. The margins of this specification sheet are marked with asterisks to indicate where changes from the previous issue were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and co

18、ntractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations and relationship to the last previous issue. Custodians: Preparing activity: Army - CR DLA - CC Navy - EC Air Force 11 (Project 5915-2008-017) DLA - CC Review acti

19、vities: Army AT, AV Navy - AS, CG, MC, SH Air Force - 19, 99 * NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-