DLA MIL-PRF-15733 57 D-2009 FILTER RADIO FREQUENCY INTERFERENCE HERMETICALLY SEALED STYLE FL62 [Use DLA MIL-PRF-28861 5 C (1) DLA MIL-PRF-28861 5C DLA MIL-PRF-28861 5B (1) DLA MIL-.pdf

1、 AMSC N/A FSC 5915 MIL-PRF-15733/57D 23 April 2009 SUPERSEDING MIL-PRF-15733/57C 28 May 2003 PERFORMANCE SPECIFICATION SHEET FILTER, RADIO FREQUENCY INTERFERENCE, HERMETICALLY SEALED, STYLE FL62 * This specification sheet is approved for use by all Depart- ments and Agencies of the Department of Def

2、ense. The complete requirements for acquiring the filters described herein shall consist of this specification sheet and MIL-PRF-15733. * Inactive for new design after 23 April 2009. Used for replacement purposes only. For new design use MIL-PRF-28861/5; PIN M28861/05-005TB. INCH-POUNDFIGURE 1. Case

3、 dimensions and circuit diagram. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-15733/57D 2 Inches mm .005 0.13 .010 0.25 .020 0.51 .022 0.56 .050 1.27 .070 1.78 .093 2.36 .120 3.05 .187 4.75 .190 4.83 .201 5.11 .250 6.35 .312 7.92 .352 8.94

4、 .400 10.16 .408 10.36 .630 16.00 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only. 3. Circuit diagram is for information only. 4. All filters shall be supplied with mounting hardware. 5. Use of style FL62 with or without shoulder is optional 6. Option

5、al terminal hole .070 .010 inches or terminal slot .050 .010 x .070 .010 inches may be supplied. 7. Terminal identification (non-symmetrical filters): The case shall be marked at the threaded end of the filter with the symbol “L”. FIGURE 1. Case dimensions and circuit diagram - Continued. Provided b

6、y IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-15733/57D 3 REQUIREMENTS: Dimensions and configuration: See figure 1. Case: Metal. * Case and mounting hardware finish: In accordance with MIL-PRF-15733. Pure tin finish is prohibited as specified in MIL-

7、PRF-15733. Terminals: Solder lug. Operating temperature range: -55C to +125C. Rated voltage: 150 V dc at 125C; 125 V ac, 400 hertz at 125C. Rated current: See table I. Insertion loss: In accordance with MIL-PRF-15733 and table I. TABLE I. Electrical characteristics. Minimum insertion loss (dB) in ac

8、cordance with MIL-STD-220 1/ At +25C At -55C and +125C Dash number Maximum rated current (ampere) 100 kHz 150 kHz 300 kHz 1 MHz 10 MHz 100 MHz 1 GHz 100 kHz 150 kHz 300 kHz 1 MHz 10 MHz 100 MHz 1 GHz 0001 0.5 18 24 28 58 60 60 60 16 22 26 56 60 60 60 1/ Insertion loss measurements shall be made unde

9、r full load over the frequency range of 100 kHz to 10 MHz. Insertion loss measurements above this frequency range shall be under no-load. Seal: In accordance with MIL-PRF-15733. Temperature rise: In accordance with MIL-PRF-15733; 25C, maximum. Dielectric withstanding voltage: In accordance with MIL-

10、PRF-15733. The following exceptions shall apply: Test temperature: 25C. Test voltage: 2.0 times the rated dc voltage applied between each terminal and ground, for a period of 1 to 5 seconds. Barometric pressure (reduced): In accordance with MIL-PRF-15733 and method 105, MIL-STD-202; test condition C

11、 (70,000 ft). The following details apply: Dielectric withstanding voltage: 125 percent of the rated dc voltage for 60 seconds. Insulation resistance: In accordance with MIL-PRF-15733. The following details and exceptions shall apply: Test temperature: 25C. Test potential: Rated dc voltage. Maximum

12、charging current: 150 milliamperes for 2 minutes. Insulation resistance: Shall be not less than 1,000 megohms. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-15733/57D 4 Voltage drop: .18 volt, maximum. Overload: In accordance with MIL-PRF-1

13、5733. After the filter has returned to room temperature, the insulation resistance and voltage drop measurements shall meet initial requirements. Terminal strength: In accordance with MIL-PRF-15733 and method 211, MIL-STD-202; test condition A (pull). Force: 5 pounds. Salt atmosphere (corrosion): In

14、 accordance with MIL-PRF-15733 and method 101, MIL-STD-202; test condition A. Shock (specified pulse): In accordance with MIL-PRF-15733 and method 213, MIL-STD-202; test condition I. Vibration, high frequency: In accordance with MIL-PRF-15733 and method 204, MIL-STD-202; test condition B (15 g). Lif

15、e: In accordance with MIL-PRF-15733 and method 108, MIL-STD-202; test condition B (250 hours). Part or Identifying Number (PIN): M15733/57-0001. NOTES: * Referenced documents: In addition to MIL-PRF-15733, this specification sheet references the following documents: MIL-PRF-28861/5 MIL-STD-202 MIL-S

16、TD-220 * Changes from previous issue: The margins of this specification sheet are marked with asterisks to indicate where changes from the previous issue were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders

17、 and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notationsd relationship to the last previous issue. Custodians: Preparing activity: Navy - EC DLA - CC Air Force - 85 DLA CC (Project 5915-2009-002) * NOTE: The activ

18、ities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-