DLA MIL-PRF-32159 12 (2)-2013 RESISTORS CHIP FIXED FILM ZERO OHM INDUSTRIAL HIGH RELIABILITY SPACE LEVEL STYLE RCZ0603.pdf

1、INCH-POUND MIL-PRF-32159/12 w/ Amendment 2 21 February 2013 SUPERSEDING MIL-PRF-32159/12 w/ Amendment 1 6 December 2007 PERFORMANCE SPECIFICATION RESISTORS, CHIP, FIXED, FILM, ZERO OHM, INDUSTRIAL, HIGH RELIABILITY, SPACE LEVEL, STYLE RCZ0603 This specification is approved for use by all Departments

2、 and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-PRF-32159. 1. SCOPE * 1.1 Scope. This specification covers the requirements for style RCZ0603, fixed, film, chip, zero ohm, industrial, high relia

3、bility, space level resistors. This style is available in all termination materials. Designers are CAUTIONED on using these resistors in high power pulses application (see 6.5). 1.2 Part or Identifying Number (PIN). Chip resistors covered by this specification are identified by a PIN which must cons

4、ist of the basic number of this specification and a coded dash number. The PIN must be in the following form: M32159 | B12C | Performance specification number Coded dash number The coded dash number must be derived in accordance with MIL-PRF-32159. 2. APPLICABLE DOCUMENTS * 2.1 General. The document

5、s listed in this section are specified in sections 3, 4 or 5 of this specification. This section does not include documents cited in other sections of this specification or recommended for additional information or as examples. While every effort has been made to ensure the completeness of this list

6、, document users are cautioned that they must meet all specified requirements of documents in sections 3, 4 or 5 of this specification, whether or not they are listed. AMSC N/A FSC 5905 Comments, suggestions, or questions on this document should be addressed to DLA Land and Maritime, ATTN: VAT, Post

7、 Office Box 3990, Columbus, OH 43218-3990, or emailed to Resistordla.mil. Since contact information can change, you may want to verify the currency of this address information using the ASSIST Online database at https:/assist.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permit

8、ted without license from IHS-,-,-MIL-PRF-32159/12 w/ Amendment 2 2 2.2 Government documents. 2.2.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks forms a part of this document to the extent specified herein. Unless otherwise specified, the issues of

9、these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-32159 - Resistors, Chip, Fixed, Film, Zero Ohm, Industrial, High Reliability, Space Level, General Specification for. * (Copies of these documents are available online at https:/assist.dla.mi

10、l/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) * 2.3 Order of precedence. Unless otherwise noted herein or in the contract, in the event of a conflict between the text of this document and the references cited herein, (e

11、xpect for related associated specifications, specification sheets or MS standards), the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 General. The requirements f

12、or acquiring the product described herein shall consist of this document and MIL-PRF-32159. 3.2 Interface and physical dimensions. Resistors shall meet the interface and physical dimensions specified on figure 1, as applicable. 3.3. Power rating. The power rating shall be 0.070 watts. 3.4 Current ra

13、ting (by termination). The maximum current rating shall be 1.5 amps for terminations B/G, 1.1 amps for termination styles C/D, and 0.68 amps for termination styles U/T. 3.5 Resistance (by termination). Maximum resistance value shall be 0.030 ohms for termination styles B/G, 0.060 ohms for terminatio

14、n styles C/D, and 0.150 ohms for termination styles U/T. 4. VERIFICATION 4.1 Verification. Verification shall be in accordance with MIL-PRF-32159. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-32159/12 w/ Amendment 2 3 CONFIGURATION A CONFI

15、GURATION B Inches mm Inches mm 0.005 0.13 0.032 .81 0.006 0.15 0.033 .84 0.010 0.25 0.060 1.52 0.012 0.31 0.064 1.63 0.015 0.38 Configuration Dimension A Inch Dimension B Inch Dimension C Inch Dimension D Inch Dimension E Inch A 0.060 .005 0.032 .005 0.010 / 0.033 0.010 .005 N/A B 0.064 .006 0.032 .

16、005 0.010 / 0.033 0.012 .005 0.015 .005 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only. 3. Unless otherwise specified, tolerance is .005 (0.13 mm). 4. The pictorial view of the styles above is given as representative of the envelope of the item. Slig

17、ht deviations from the outline shown, which are contained within the envelope, and do not alter the functional aspects of the device are acceptable. 5. Configuration A covers termination materials D, and T. 6. Configuration B covers termination materials B, C, G, and U. FIGURE 1. Style RCZ0603. Prov

18、ided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-32159/12 w/ Amendment 2 4 5. PACKAGING 5.1 Packaging. For acquisition purposes, the packaging requirements shall be as specified in the contract or order (see 6.2). When packaging of materiel is to

19、be performed by DoD or in-house contractor personnel, these personnel need to contact the responsible packaging activity to ascertain packaging requirements. Packaging requirements are maintained by the Inventory Control Points packaging activity within the Military Service or Defense Agency, or wit

20、hin the military services system commands. Packaging data retrieval is available from the managing Military Departments or Defense Agencys automated packaging files, CD-ROM products, or by contacting the responsible packaging activity. 6. NOTES (This section contains information of a general or expl

21、anatory nature that may be helpful, but is not mandatory.) 6.1 Intended use. Chip resistors are intended to be use in thin or thick film hybrid circuits where micro-circuitry is indicated and in surface mount applications. 6.2 Acquisition requirements. Acquisition documents should specify the follow

22、ing: a. Title, number, date of this specification, the applicable associated specification, and the complete PIN (see 1.2). * b. Unless otherwise specified (see 2.1), the versions of the individual documents referenced will be those in effect on the date of release of the solicitation. c. Packaging

23、requirements (see 5.1). d. If marking is required (see MIL-PRF-32159). 6.3 Tolerance for wraparound termination. The added tolerance for the wraparound type termination is intended to apply only to termination, metallization, and pretinning material. * 6.4 Electrostatic charge effects. Under relativ

24、ely low humidity conditions, some types of film resistors, particularly those with small dimensions and high sheet resistivity materials, are prone to sudden significant changes in resistance (usually reductions in value) and to changes in temperature coefficient of resistance as a result of dischar

25、ge of static charges built up on associated objects during handling, packaging, or shipping. Substitution of more suitable implements and materials can help minimize this problem. For example, use cotton gloves, static eliminator devices, air humidifiers, and operator and workbench grounding systems

26、 can reduce static buildup during handling. Means of alleviating static problems during shipment include elimination of loose packaging of resistors and use of metal foil (conductive) and static dissipation packaging materials. Direct shipments to the government are controlled by MIL-DTL-39032 which

27、 specifies a preventive packaging procedure. * 6.5 Pulse applications. Designers are CAUTIONED on using these resistors in high power pulse applications. Since they have not been qualified nor tested for such applications, damages and premature failures are possible. These resistors only see a five

28、second short time overload as part of the group B inspection of MIL-PRF-32159. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-32159/12 w/ Amendment 2 5 6.6 Amendment notations. The margins of this specification are marked with asterisks to i

29、ndicate modifications generated by this amendment. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespect

30、ive of the marginal notations. Custodians: Preparing activity: Army - CR DLA -CC Navy - EC Air Force - 85 (Project 5905-2012-016) DLA CC Review activities: Army - AR, AT, AV, CR4 Navy - AS, CG, MC, OS Air Force - 19, 99 Civil agencies: NASA NA NOTE: The activities listed above were interested in thi

31、s document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-