DLA MIL-PRF-39006 25 E-2012 CAPACITORS FIXED ELECTROLYTIC (NONSOLID ELECTROLYTE) TANTALUM (POLARIZED SINTERED SLUG) (EXTENDED RANGE) 85癈 (VOLTAGE DERATED TO 125癈) ESTABLISHED RELI.pdf

1、 INCH-POUND MIL-PRF-39006/25E 7 December 2012 SUPERSEDING MIL-PRF-39006/25D 24 October 2006 PERFORMANCE SPECIFICATION SHEET CAPACITORS, FIXED, ELECTROLYTIC (NONSOLID ELECTROLYTE), TANTALUM, (POLARIZED, SINTERED SLUG), (EXTENDED RANGE) 85C (VOLTAGE DERATED TO 125C), ESTABLISHED RELIABILITY, STYLE CLR

2、81 This specification sheet is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-PRF-39006. NOTES: 1. Dimensions are in inches. 2. Metric equivalents are in pare

3、ntheses. 3. Metric equivalents are given for general information only. 4. The weld shall not be enclosed in the end seal. 5. CLR81 capacitors are replacements for the inactive CLR69s (MIL-PRF-39006/21), silver cased wet slug capacitors. 6. CLR81 capacitors have higher capacitance values than CLR79s

4、(MIL-PRF-39006/22) of the same case size and voltage rating. 7. Low ESR versions of CLR81s may be found in MIL-PRF-39006/31 (CLR91). FIGURE 1. Style CLR81 capacitors. AMSC N/A FSC 5910 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-39006/25E

5、 2 Case size Dimensions Basic case Insulated case E .250 (6.35) L 1/ +.031 (0.79) -.016 (0.41) D .016 (0.41) D max T1 .453 (11.51) .188 (4.78) .219 ( 5.56) 1.500 (38.10) T2 .641 (16.28) .281 (7.14) .312 ( 7.92) 2.250 (57.15) T3 .766 (19.46) .375 (9.52) .406 (10.31) 2.250 (57.15) T4 1.062 (26.97) .37

6、5 (9.52) .406 (10.31) 2.250 (57.15) 1/ Length of basic case sleeving shall be as specified in MIL-PRF-39006. FIGURE 1. Style CLR81 capacitors - Continued. REQUIREMENTS: Design and construction: Dimensions and configuration: See figure 1. Case type: Tantalum, tubular, insulated. Seal type: Hermetic (

7、glass-to-tantalum anode). Terminals: Axial-wire lead: Cathode and anode (type N32, N51, or N52 of MIL-STD-1276). Rated temperature: -55C to +85C, voltage derated to +125C (see figure 2). FIGURE 2. Voltage derating with temperature. Provided by IHSNot for ResaleNo reproduction or networking permitted

8、 without license from IHS-,-,-MIL-PRF-39006/25E 3 Rated voltage: See table I. Capacitance (Cap.) nominal (nom): See table I. Cap. tolerance: 10 percent or 20 percent (see table I). FR level: M, P, R, and S (see table I). DC leakage (DCL) (max) (at +25C): See table I. Cap. (nominal): Method 305 of MI

9、L-STD-202. Dissipation factor (DF) (max): See table I. Seal: Method 112 of MIL-STD-202, conditions A or D, and C. Shock (specified pulse): Method 213 of MIL-STD-202, condition I (100 gs) or condition D (500 gs), as applicable. Vibration, high frequency: Method 204 of MIL-STD-202, condition D (20 gs)

10、 or condition H (80 gs), as applicable. Random vibration (as applicable): Method 214 of MIL-STD-202, test condition II-K (51 gs). Thermal shock: Method 107 of MIL-STD-202, condition A (with step 3 at +125C). Number of cycles: In accordance with MIL-PRF-39006, the following shall apply. DCL: 200 perc

11、ent (max) of +25C value of table I for qualification and group C. DCL: 125 percent (max) of +25C value of table I for group B. Cap: Within 5 percent of initial measurement. DF: 115 percent (max) of initial requirement. Salt atmosphere (corrosion): Method 101 of MIL-STD-202, condition B (48 hours). S

12、olderability: Method 208 of MIL-STD-202. Terminal strength: Pull: Method 211 of MIL-STD-202, condition A. Wire-lead bend: In accordance with MIL-PRF-39006. Surge voltage: See table I. Moisture resistance: Method 106 of MIL-STD-202. DCL: 125 percent (max) of +25C value of table I. Cap: Within 8 perce

13、nt of initial measurement. DF: 115 percent (maximum) of initial requirement. Dielectric withstanding voltage (DWV): Method 301 of MIL-STD-202. 2,000 V dc, minimum. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-TABLE I. Capacitor characteristics. Ra

14、ted voltage (+85C) 1/ Cap. Cap. toler-ance DC leakage (max) Dissi-pation factor (max) ESR at +25C (max) 2/ Derated voltage (+125C) 1/ Surge voltage (+85C) Imped- ance (max) Capacitance change at Max 85C 40 kHz ripple current 3/ Case size PIN M39006/25- 4/ Failure rate level (%/1,000 hour) +25C +85C,

15、 +125C -55C +85C +125C M(1.0) P(0.1) R(0.01) S(0.001) V dc F percent A A percent Ohms V dc V dc Ohms percent percent percent mA rms 6 220 20 2 9 50 3.02 4 6.9 36 -64 +13 +16 1,000 T1 0001- 0089- 0177- 0265- 6 220 10 2 9 50 3.02 4 6.9 36 -64 +13 +16 1,000 T1 0002- 0090- 0178- 0266- 6 820 20 3 14 155

16、2.51 4 6.9 18 -88 +16 +20 1,500 T2 0003- 0091- 0179- 0267- 6 820 10 3 14 155 2.51 4 6.9 18 -88 +16 +20 1,500 T2 0004- 0092- 0180- 0268- 6 1,500 20 5 20 172 1.52 4 6.9 18 -90 +20 +25 1,900 T3 0005- 0093- 0181- 0269- 6 1,500 10 5 20 172 1.52 4 6.9 18 -90 +20 +25 1,900 T3 0006- 0094- 0182- 0270- 6 2,20

17、0 20 6 24 170 1.03 4 6.9 13 -90 +25 +30 2,300 T4 0007- 0095- 0183- 0271- 6 2,200 10 6 24 170 1.03 4 6.9 13 -90 +25 +30 2,300 T4 0008- 0096- 0184- 0272- 8 180 20 2 9 41 3.02 5 9.2 45 -60 +13 +16 1,000 T1 0009- 0097- 0185- 0273- 8 180 10 2 9 41 3.02 5 9.2 45 -60 +13 +16 1,000 T1 0010- 0098- 0186- 0274

18、- 8 680 20 3 14 130 2.54 5 9.2 22 -83 +16 +20 1,500 T2 0011- 0099- 0187- 0275- 8 680 10 3 14 130 2.54 5 9.2 22 -83 +16 +20 1,500 T2 0012- 0100- 0188- 0276- 8 1,500 20 5 20 170 1.50 5 9.2 18 -90 +20 +25 1,900 T3 0013- 0101- 0189- 0277- 8 1,500 10 5 20 170 1.50 5 9.2 18 -90 +20 +25 1,900 T3 0014- 0102

19、- 0190- 0278- 8 1,800 20 7 25 138 1.02 5 9.2 14 -90 +25 +30 2,300 T4 0015- 0103- 0191- 0279- 8 1,800 10 7 25 138 1.02 5 9.2 14 -90 +25 +30 2,300 T4 0016- 0104- 0192- 0280- 10 150 20 2 9 34 3.01 7 11.5 54 -55 +13 +16 900 T1 0017- 0105- 0193- 0281- 10 150 10 2 9 34 3.01 7 11.5 54 -55 +13 +16 900 T1 00

20、18- 0106- 0194- 0282- 10 560 20 3 16 106 2.51 7 11.5 27 -77 +16 +20 1,450 T2 0019- 0107- 0195- -0283- 10 560 10 3 16 106 2.51 7 11.5 27 -77 +16 +20 1,450 T2 0020- 0108- 0196- 0284- 10 1,200 20 5 20 137 1.51 7 11.5 18 -88 +20 +25 1,850 T3 0021- 0109- 0197- 0285- 10 1,200 10 5 20 137 1.51 7 11.5 18 -8

21、8 +20 +25 1,850 T3 0022- 0110- 0198- 0286- 10 1,500 20 7 25 114 1.01 7 11.5 15 -88 +25 +30 2,300 T4 0023- 0111- 0199- 0287- 10 1,500 10 7 25 114 1.01 7 11.5 15 -88 +25 +30 2,300 T4 0024- 0112- 0200- 0288- 15 100 20 2 9 30 3.98 10 17.2 72 -44 +13 +16 900 T1 0025- 0113- 0201- 0289- 15 100 10 2 9 30 3.

22、98 10 17.2 72 -44 +13 +16 900 T1 0026- 0114- 0202- 0290- 15 390 20 3 16 74 2.52 10 17.2 31 -66 +16 +20 1,450 T2 0027- 0115- 0203- 0291- 15 390 10 3 16 74 2.52 10 17.2 31 -66 +16 +20 1,450 T2 0028- 0116- 0204- 0292- 15 820 20 6 24 111 1.80 10 17.2 22 -77 +20 +25 1,800 T3 0029- 0117- 0205- 0293- 15 82

23、0 10 6 24 111 1.80 10 17.2 22 -77 +20 +25 1,800 T3 0030- 0118- 0206- 0294- 15 1,000 20 8 32 92 1.22 10 17.2 17 -77 +25 +30 2,300 T4 0031- 0119- 0207- 0295- 15 1,000 10 8 32 92 1.22 10 17.2 17 -77 +25 +30 2,300 T4 0032- 0120- 0208- 0296- 25 68 20 2 9 22 4.29 15 28.8 90 -40 +12 +15 850 T1 0033- 0121-

24、0209- 0297- 25 68 10 2 9 22 4.29 15 28.8 90 -40 +12 +15 850 T1 0034- 0122- 0210- 0298- 25 270 20 3 16 55 2.70 15 28.8 33 -62 +13 +16 1,400 T2 0035- 0123- 0211- 0299- 25 270 10 3 16 55 2.70 15 28.8 33 -62 +13 +16 1,400 T2 0036- 0124- 0212- 0300- See footnotes at end of table. MIL-PRF-39006/25E4Provid

25、ed by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-TABLE I. Capacitor characteristics - Continued. Rated voltage (+85C) 1/ Cap. Cap. toler-ance DC leakage (max) Dissi-pation factor (max) ESR at +25C (max) 2/ Derated voltage (+125C) 1/ Surge voltage (+85C) Imp

26、ed- ance (max) Capacitance change at Max 85C 40 kHz ripple current 3/ Case size PIN M39006/25- 4/ Failure rate level (%/1,000 hour) +25C +85C, +125C -55C +85C +125C M(1.0) P(0.1) R(0.01) S(0.001) V dc F percent A A percent Ohms V dc V dc Ohms percent percent percent mA rms 25 560 20 7 28 76 1.80 15

27、28.8 24 -72 +20 +25 1,750 T3 0037- 0125- 0213- 0301- 25 560 10 7 28 76 1.80 15 28.8 24 -72 +20 +25 1,750 T3 0038- 0126- 0214- 0302- 25 680 20 8 32 63 1.23 15 28.8 19 -72 +25 +30 2,100 T4 0039- 0127- 0215- 0303- 25 680 10 8 32 63 1.23 15 28.8 19 -72 +25 +30 2,100 T4 0040- 0128- 0216- 0304- 30 56 20 2

28、 9 22 5.21 20 34.5 100 -38 +12 +15 800 T1 0041- 0129- 0217- 0305- 30 56 10 2 9 22 5.21 20 34.5 100 -38 +12 +15 800 T1 0042- 0130- 0218- 0306- 30 220 20 3 16 42 2.53 20 34.5 36 -60 +13 +16 1,200 T2 0043- 0131- 0219- 0307- 30 220 10 3 16 42 2.53 20 34.5 36 -60 +13 +16 1,200 T2 0044- 0132- 0220- 0308-

29、30 470 20 8 32 64 1.81 20 34.5 25 -65 +20 +25 1,500 T3 0045- 0133- 0221- 0309- 30 470 10 8 32 64 1.81 20 34.5 25 -65 +20 +25 1,500 T3 0046- 0134- 0222- 0310- 30 560 20 9 36 55 1.30 20 34.5 20 -65 +25 +30 2,000 T4 0047- 0135- 0223- 0311- 30 560 10 9 36 55 1.30 20 34.5 20 -65 +25 +30 2,000 T4 0048- 01

30、36- 0224- 0312- 50 33 20 2 9 12.3 4.95 30 57.5 135 -29 +10 +12 700 T1 0049- 0137- 0225- 0313- 50 33 10 2 9 12.3 4.95 30 57.5 135 -29 +10 +12 700 T1 0050- 0138- 0226- 0314- 50 120 20 4 24 22.5 2.49 30 57.5 49 -42 +12 +15 1,200 T2 0051- 0139- 0227- 0315- 50 120 10 4 24 22.5 2.49 30 57.5 49 -42 +12 +15

31、 1,200 T2 0052- 0140- 0228- 0316- 50 270 20 8 32 37 1.82 30 57.5 29 -46 +20 +25 1,450 T3 0053- 0141- 0229- 0317- 50 270 10 8 32 37 1.82 30 57.5 29 -46 +20 +25 1,450 T3 0054- 0142- 0230- 0318- 50 330 20 9 36 38 1.53 30 57.5 22 -46 +25 +30 1,900 T4 0055- 0143- 0231- 0319- 50 330 10 9 36 38 1.53 30 57.

32、5 22 -46 +25 +30 1,900 T4 0056- 0144- 0232- 0320- 60 27 20 3 12 10.2 5.01 40 69.0 144 -24 +10 +12 700 T1 0057- 0145- 0233- 0321- 60 27 10 3 12 10.2 5.01 40 69.0 144 -24 +10 +12 700 T1 0058- 0146- 0234- 0322- 60 100 20 4 20 19 2.52 40 69.0 54 -36 +12 +15 1,100 T2 0059- 0147- 0235- 0323- 60 100 10 4 2

33、0 19 2.52 40 69.0 54 -36 +12 +15 1,100 T2 0060- 0148- 0236- 0324- 60 220 20 8 32 30 1.81 40 69.0 29 -40 +16 +20 1,400 T3 0061- 0149- 0237- 0325- 60 220 10 8 32 30 1.81 40 69.0 29 -40 +16 +20 1,400 T3 0062- 0150- 0238- 0326- 60 270 20 9 36 27 1.33 40 69.0 23 -45 +20 +25 1,850 T4 0063- 0151- 0239- 032

34、7- 60 270 10 9 36 27 1.33 40 69.0 23 -45 +20 +25 1,850 T4 0064- 0152- 0240- 0328- 75 22 20 3 12 8.5 5.13 50 86.2 157 -19 +10 +12 600 T1 0065- 0153- 0241- 0329- 75 22 10 3 12 8.5 5.13 50 86.2 157 -19 +10 +12 600 T1 0066- 0154- 0242- 0330- 75 82 20 4 24 15.2 2.46 50 86.2 63 -30 +12 +15 1,000 T2 0067-

35、0155- 0243- 0331- 75 82 10 4 24 15.2 2.46 50 86.2 63 -30 +12 +15 1,000 T2 0068- 0156- 0244- 0332- See footnotes at end of table. MIL-PRF-39006/25E5Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-TABLE I. Capacitor characteristics - Continued. Rated v

36、oltage (+85C) 1/ Cap. Cap. toler-ance DC leakage (max) Dissi-pation factor (max) ESR at +25C (max) 2/ Derated voltage (+125C) 1/ Surge voltage (+85C) Imped- ance (max) Capacitance change at Max 85C 40 kHz ripple current 3/ Case size PIN M39006/25- 4/ Failure rate level (%/1,000 hour) +25C +85C, +125

37、C -55C +85C +125C M(1.0) P(0.1) R(0.01) S(0.001) V dc F percent A A percent Ohms V dc V dc Ohms percent percent percent mA rms 75 180 20 9 36 24.4 2.23 50 86.2 30 -35 +16 +20 1,300 T3 0069- 0157- 0245- 0333- 75 180 10 9 36 24.4 2.23 50 86.2 30 -35 +16 +20 1,300 T3 0070- 0158- 0246- 0334- 75 220 20 1

38、0 40 37.0 1.80 50 86.2 24 -40 +20 +25 1,800 T4 0071- 0159- 0247- 0335- 75 220 10 10 40 37.0 1.80 50 86.2 24 -40 +20 +25 1,800 T4 0072- 0160- 0248- 0336- 100 10 20 3 12 4.5 5.97 65 115.0 200 -17 +10 +12 800 T1 0073- 0161- 0249- 0337- 100 10 10 3 12 4.5 5.97 65 115.0 200 -17 +10 +12 800 T1 0074- 0162-

39、 0250- 0338- 100 39 20 5 24 10.4 3.54 65 115.0 80 -20 +12 +15 1,300 T2 0075- 0163- 0251- 0339- 100 39 10 5 24 10.4 3.54 65 115.0 80 -20 +12 +15 1,300 T2 0076- 0164- 0252- 0340- 100 68 20 10 40 11.3 2.21 65 115.0 40 -30 +14 +16 1,600 T3 0077- 0165- 0253- 0341- 100 68 10 10 40 11.3 2.21 65 115.0 40 -3

40、0 +14 +16 1,600 T3 0078- 0166- 0254- 0342- 100 120 20 12 48 25 2.76 65 115.0 30 -35 +15 +17 2,000 T4 0079- 0167- 0255- 0343- 100 120 10 12 48 25 2.76 65 115.0 30 -35 +15 +17 2,000 T4 0080- 0168- 0256- 0344- 125 6.8 20 3 12 6.0 11.71 85 144.0 300 -14 +10 +12 700 T1 0081- 0169- 0257- 0345- 125 6.8 10

41、3 12 6.0 11.71 85 144.0 300 -14 +10 +12 700 T1 0082- 0170- 0258- 0346- 125 27 20 5 24 7.2 3.54 85 144.0 90 -18 +12 +15 1,200 T2 0083- 0171- 0259- 0347- 125 27 10 5 24 7.2 3.54 85 144.0 90 -18 +12 +15 1,200 T2 0084- 0172- 0260- 0348- 125 47 20 10 40 7.9 2.23 85 144.0 50 -26 +14 +16 1,500 T3 0085- 017

42、3- 0261- 0349- 125 47 10 10 40 7.9 2.23 85 144.0 50 -26 +14 +16 1,500 T3 0086- 0174- 0262- -0350- 125 82 20 12 48 17.4 2.82 85 144.0 32 -30 +15 +17 1,900 T4 0087- 0175- 0263- 0351- 125 82 10 12 48 17.4 2.82 85 144.0 32 -30 +15 +17 1,900 T4 0088- 0176- 0264- 0352- 1/ Reverse voltage rating at +85C is

43、 3 V dc and at +125C is 2 V dc. 2/ Maximum ESR is calculated by the following equation: ESR (max) = CfDF2, where: DF = Maximum dissipation factor from table I; f = 120 Hz; C = Nominal capacitance. 3/ For ripple current limits at various temperatures, voltages, and frequencies, see table II. 4/ Dash

44、number shall include the letter “H” to indicate the optional vibration and shock requirements (i.e., 53.79 gs random vibration,80 gs sinusoidal vibration, and 500 gs shock) or the “-“ will be deleted. The acquiring activity may substitute an “H” designated part in place of a non “H” designated part

45、at their option. MIL-PRF-39006/25E6Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-TABLE II. Ripple current multipliers versus frequency, temperature, and applied peak voltage. 1/ 2/ 3/ 4/ 5/ Frequency of applied ripple current Ambient still air 120

46、Hz 800 Hz 1 kHz 10 kHz 40 kHz 100 kHz Temp C Temp C Temp C Temp C Temp C Temp C 55 85 105 125 55 85 105 125 55 85 105 125 55 85 105 125 55 85 105 125 55 85 105 125 6/ 100 percent 90 percent 80 percent 70 percent 66 2/3 percent .60 .60 .60 .60 .60 .39 .46 .52 .58 .60 - - .35 .44 .46 - - - - .27 .71 .

47、71 .71 .71 .71 .43 .55 .62 .69 .71 - - .42 .52 .55 - - - - .32 .72 .72 .72 .72 .72 .45 .55 .62 .70 .72 - - .42 .52 .55 - - - - .32 .88 .88 .88 .88 .88 .55 .67 .76 .85 .88 - - .52 .64 .68 - - - - .40 1.0 1.0 1.0 1.0 1.0 .63 .77 .87 .97 1.0 - - .59 .73 .77 - - - - .45 1.1 1.1 1.1 1.1 1.1 .69 .85 .96 1.07 1.1 - - .65 .80 .85 - - - - .50 1/ At +125C, the rated voltage of the capacitors decreases to 66.67 percent of the +85C rated voltage. 2/ The peak of the applied ac ripple voltage plus th