ImageVerifierCode 换一换
格式:PDF , 页数:5 ,大小:61.08KB ,
资源ID:692860      下载积分:10000 积分
快捷下载
登录下载
邮箱/手机:
温馨提示:
如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
如填写123,账号就是123,密码也是123。
特别说明:
请自助下载,系统不会自动发送文件的哦; 如果您已付费,想二次下载,请登录后访问:我的下载记录
支付方式: 支付宝扫码支付 微信扫码支付   
注意:如需开发票,请勿充值!
验证码:   换一换

加入VIP,免费下载
 

温馨提示:由于个人手机设置不同,如果发现不能下载,请复制以下地址【http://www.mydoc123.com/d-692860.html】到电脑端继续下载(重复下载不扣费)。

已注册用户请登录:
账号:
密码:
验证码:   换一换
  忘记密码?
三方登录: 微信登录  

下载须知

1: 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。
2: 试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。
3: 文件的所有权益归上传用户所有。
4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
5. 本站仅提供交流平台,并不能对任何下载内容负责。
6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。

版权提示 | 免责声明

本文(DLA MIL-PRF-39012 128 C-2011 CONNECTORS RECEPTACLE ELECTRICAL COAXIAL RADIO FREQUENCY (SERIES BNC SOLDER POCKET SOCKET CONTACT JAM NUT MOUNTED ISOLATED CLASS 2).pdf)为本站会员(confusegate185)主动上传,麦多课文库仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文库(发送邮件至master@mydoc123.com或直接QQ联系客服),我们立即给予删除!

DLA MIL-PRF-39012 128 C-2011 CONNECTORS RECEPTACLE ELECTRICAL COAXIAL RADIO FREQUENCY (SERIES BNC SOLDER POCKET SOCKET CONTACT JAM NUT MOUNTED ISOLATED CLASS 2).pdf

1、AMSC N/A FSC 5935 INCH-POUND MIL-PRF-39012/128C 16 November 2011 SUPERSEDING MIL-PRF-39012/128B 19 September 1989 PERFORMANCE SPECIFICATION SHEET CONNECTORS, RECEPTACLE, ELECTRICAL, COAXIAL, RADIO FREQUENCY, (SERIES BNC, SOLDER POCKET, SOCKET CONTACT JAM NUT MOUNTED, ISOLATED, CLASS 2) This specific

2、ation is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-PRF-39012. FIGURE 1. General configuration. Provided by IHSNot for ResaleNo reproduction or networking

3、 permitted without license from IHS-,-,-MIL-PRF-39012/128C 2 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for information only. 3. Unless otherwise specified all tolerances are .005(0.13mm) inches 4. Wrench flats are to accommodate standard wrench opening in accordance with FE

4、D-STD-H28, appendix 10. 4. All undimensioned pictorial configurations are for reference purposes only. 5. Solder pocket shall accommodate a wire of .059 (1.50 mm) diameter maximum. 6. Series BNC, socket contact interface in accordance with MIL-STD-348. FIGURE 1. General configuration - Continued. In

5、ches mm Inches mm Inches mm .016 0.41 .023 0.58 .046 1.17 .063 1.60 .105 2.67 .130 3.30 .176 4.47 .215 5.46 .225 5.72 .227 5.77 .230 5.84 .414 10.52 .492 12.45 .500 12.70 .504 12.80 .591 15.01 .635 16.13 1.20 30.48 Provided by IHSNot for ResaleNo reproduction or networking permitted without license

6、from IHS-,-,-MIL-PRF-39012/128C 3 ENGINEERING DATA: Nominal impedance: 50 ohms. Frequency range: 0 to 4 GHz. Voltage rating: 500 V rms maximum working voltage at sea level; 125 V rms maximum at 70,000 feet. Temperature rating: -65C to +165C. REQUIREMENTS: Dimensions and configuration: See figure 1.

7、Center contacts; Axial force: 4lbs, minimum Radial torque: 4 inch-ounces, minimum Isolating insulator captivation: Forces shall be applied between the mounting bushing and connector body for a period of 10 seconds, minimum. Torque: 15 inch-pounds Axial force: 30 pounds. Force to engage and disengage

8、: Longitudinal force: 3 pound maximum. Torque: 2 inch-pounds maximum. Coupling proof torque: Not applicable. Inspection conditions(coupling torque): Not applicable. Mating characteristics: See MIL-STD-348. Center contact (socket): Oversized test pin: .057 diameter, minimum (non-closed entry contacts

9、 only). Insertion depth: .125, minimum. Number of insertions: one. Insertion force test: Steel test pin diameter .054, minimum. Test pin finish: 16 micro inches Insertions force: 2 pounds, maximum Withdrawal force test: Steel test pin diameter .052, minimum. Withdrawal force: 2 ounces minimum. Test

10、pin finish: 16 micro inches Hermetic seal: Not applicable. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-39012/128C 4 Leakage (pressurized connectors): Not applicable. Insulation resistance: In accordance with MIL-STD-202, method 302, test

11、condition B, 5,000 megohms minimum. Contact resistance: In milliohms, maximum. Initial After environment Center contact: 1.5 2.0 Outer contact: 2.0 Not applicable Resistance to test prod damage: Not applicable. Corrosion (Salt spray): In accordance with MIL-STD-202 method 101, test condition B. Volt

12、age standing wave ratio (VSWR): Not applicable. Dielectric withstanding voltage at sea level: In accordance with MIL-STD-202, method 301. 1,500 V rms, minimum at sea level. Connector durability: 500 cycles minimum at 12 cycles per minute maximum. The connector shall meet mating characteristics and f

13、orce to engage and disengage requirements. Vibration, high frequency: In accordance with MIL-STD-202, method 204, test condition D. Shock: In accordance with MIL-STD-202, method 213, test condition C. Thermal shock: In accordance with MIL-STD-202, method 107, test condition B, except high temperatur

14、e shall be +85C. High temperature shall be +200C for connectors using +200C cables. Moisture resistance: In accordance with MIL-STD-202, method 106 (no measurements at high humidity). Insulation resistance shall be at least 200 Megaohms within 5 minutes after removal from humidity. Dielectric withst

15、anding voltage shall be met. Voltages shall be applied at points suitable for testing each individual insulator. Corona level: Voltage: 375 Volts, minimum. Altitude: 70,000 feet RF high potential withstanding voltage: Voltage and frequency: 1000 V rms, tested at a frequency from 5 to 7.5 MHz. Leakag

16、e current: Not applicable. Cable retention force: Not applicable. RF leakage: Not applicable. RF insertion loss: Not applicable. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-39012/128C 5 Isolation: The following test shall be accomplished

17、after the shock test to verify isolation. Voltages shall be applied at two points suitable for testing only the insulator providing the isolation. Insulation resistance: in accordance with MIL-STD-202,method 302, test condition B. 5000 Megaohms, minimum. Dielectric withstanding voltage: in accordanc

18、e with MIL-STD-202, method 301. 1500 Vrms, minimum. Part or Identifying Number (PIN): M39012/128-0001 Changes from previous issue. The margins of this specification are marked with vertical lines to indicate where changes from the previous issue were made. This was done as a convenience only and the

19、 Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations and relationship to the last previous issue. Referenced document

20、s. In addition to MIL-PRF-39012, this document references the following: MIL-STD-348 MIL-STD-202 FED-STD-H28 CONCLUDING MATERIAL Custodians: Preparing activity: Army - CR DLA - CC Navy - EC Air Force - 85 (Project 5935-2009-112) DLA - CC Review activities: Army - AT, AV, EA, MI Navy - AS, MC, OS, SA

21、, SH Air Force - 19, 99 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-

copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
备案/许可证编号:苏ICP备17064731号-1