DLA MIL-PRF-39012 34 B-2013 CONNECTORS COAXIAL RADIO FREQUENCY (SERIES TNC (UNCABLED) RECEPTACLE SOCKET HERMETIC SEALED JAM NUT MOUNTED CLASS 2).pdf

1、AMSC N/A FSC 5935 INCH-POUND MIL-PRF-39012/34B 09 September 2013 SUPERSEDING MIL-C-39012/34A 11 January 1973 PERFORMANCE SPECIFICATION SHEET CONNECTORS, COAXIAL, RADIO FREQUENCY (SERIES TNC (UNCABLED) RECEPTACLE, SOCKET, HERMETIC SEALED, JAM NUT MOUNTED, CLASS 2) This specification is approved for u

2、se by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-PRF-39012. FIGURE 1. General configuration. Provided by IHSNot for ResaleNo reproduction or networking permitted without lice

3、nse from IHS-,-,-MIL-PRF-39012/34B 2 Inches mm Inches mm Inches mm .022 .062 .087 .099 .104 .114 .153 .156 .56 1.57 2.21 2.51 2.64 2.90 3.89 3.96 .159 .215 .218 .221 .368 .375 .380 .384 4.04 5.46 5.54 5.61 9.35 9.53 9.65 9.75 .4375 .495 .500 .505 .508 .510 .620 .630 11.11 12.57 12.70 12.83 12.90 12.

4、95 15.75 16.00 NOTES: 1. Dimensions are in inches. 2. For dimensions A, B, and C see table I. 3. Dimension B is the largest overall diameter of the connector. 4. Metric equivalents (to the nearest .01 mm) are given for general information only. 5. All undimensioned pictorial configurations are for r

5、eference purposes only. FIGURE 1. General configuration Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-39012/34B 3 FIGURE 2. Mating dimensions for female terminations. Ltr Dimensions in inches with metric equivalents (mm) in paren

6、theses Minimum Maximum A .378 (9.60) .381 (9.68) B .345 (8.76) .356 (9.04) C .327 (8.31) .333 (8.46) D .319 (8.10) .321 (8.15) E .186 (4.72) F .068 (1.73) .088 (2.24) G .329 (8.36) .333 (8.46) H .187 (4.75) J .186 (4.72) .206 (5.23) K .006 (.15) L .195 (4.95) M .081 (2.06) .087 (2.21) N .256 (6.50)

7、P .188 (4.78) .208 (5.28) R .415 (10.56) S .015 (.38) .030 (.76) 1. Metric equivalents (to the nearest .01 mm) are given for general information only. 2. All undimensioned pictorial configurations are for reference purposes only. 3. N dimension applies to that portion (If applicable of the dielectri

8、c which protrudes beyond the metal shoulder (or reference plane) by dimension K. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-39012/34B 4 TABLE I. Dash number and overall dimensions. Dash No. Dim Inches-millimeters 1/ Maximum panel thickne

9、ss Minimum Maximum 0001 A B C .684 (17.37) .769 (19.53) 1.343 (34.11) .690 (17.53) .893 (22.68) .125 (3.18) 0002 A B C .630 (16.00) .626 (15.90) 1.328 (33.73) .650 (16.51) .750 (19.05) .250 (6.35) 1/ Millimeters are in parentheses. TABLE II. Group qualification. Group Submission and qualification of

10、 any of the following connectors Qualifies the following connectors I 0001 0002 0001 0002 ENGINEERING DATA Nominal impedance: 50 ohms. Frequency range: 0 to 11,000 MHz. Voltage rating: 500 volts rms maximum working voltage at sea level, 125 volts rms maximum at 70,000 feet. Temperature rating: -65C

11、to +165C. REQUIREMENTS Dimensions and configuration: See figure 1. Force to engage and disengage: Longitudinal force Not applicable. Torque 2 inch-pounds maximum. Coupling proof torque: Not applicable. Inspection conditions: Coupling torque 4 to 6 inch-pounds. Mating characteristics: See figure 2 fo

12、r dimensions. Center contact (female) Oversize test pin - .057 diameter minimum (non-closed entry contacts only). Insertion depth - .125 minimum. Number of insertions 1. Insertion force test Steel test pin dia .054 minimum. Test pin finish 16 microinches. Insertion force 2 lbs maximum. Provided by I

13、HSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-39012/34B 5 Withdrawal force test: Steel test pin dia .052 maximum. Withdrawal force 2 oz minimum. Test pin finish 16 microinches. Hermetic seal: Leakage shall not exceed 1 x 10-5 cc/sec of tracer gas at atm

14、ospheric pressure. Leakage (pressurized connectors): Connector mounted in mounting hole specified on figure 1 with mating end capped. Test applicable to mounting seal only. Air pressure 30 psi. Duration: 30 seconds minimum. Insulation resistance: Method 302, test condition B, MIL-STD-202. 5,000 mego

15、hms minimum. Center contact retention: 6 lbs minimum axial force. 4 inch-ounces radial torque minimum. Corrosion (salt spray): Method 101, test condition B, MIL-STD-202. Voltage standing wave ratio (VSWR): Not applicable. Connector durability: 500 cycles at 12 cycles/minute maximum. The connector sh

16、all meet the mating characteristics and force to engage and disengage requirements. Contact resistance: In milliohms maximum. Contact Initial After environment Center contact 4.0 5.0 Outer contact .2 Not applicable. Dielectric withstanding voltage: Method 301 of MIL-STD-202. 1,500 volts rms minimum

17、at sea level. Vibration, high frequency: Method 204, test condition C, MIL-STD-202. Group qualification: See table II. Shock: Method 213 of MIL-STD-202, test condition I. Temperature cycling: Method 102, test condition C, MIL-STD-202, except test high temperature shall be +200C. Thermal shock: Not a

18、pplicable. Moisture resistance: Method 106 of MIL-STD-202. No measurements at high humidity. Insulation resistance shall be at least 200 megohms within 5 minutes after removal from humidity. Corona level: Voltage 375 volts, minimum. Altitude 70,000 feet. RF high potential withstanding voltage: Volta

19、ge and frequency: 1,000 volts rms at 5 MHz. Leakage current: Not applicable. Cable retention force: Not applicable. Coupling mechanism retention force: Not applicable. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-39012/34B 6 RF leakage: No

20、t applicable. Insertion loss: Not applicable. Part or Identifying Number (PIN): M39012/34 (dash number from table I) Changes from previous issues. Changes from previous issue. Marginal notations are not used in this revision to identify changes with respect to the previous issue due to the extent of

21、 the changes. Referenced documents. In addition to MIL-PRF-39012, this document references the following: MIL-STD-202 CONCLUDING MATERIAL Custodians: Preparing activity: Army CR DLA-CC Navy EC Air Force 85 DLA - CC Review activities: Army AT, AV, EA, MI Navy AS, MC, OS, SH Air Force 19, 99 (Project

22、5935-2013-194) NASA - NA NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-