DLA MIL-PRF-39012 4 F-2013 CONNECTORS COAXIAL RADIO FREQUENCY (SERIES N (UNCABLED) RECEPTACLES JAM NUT AND FLANGE MOUNTED SOCKET CONTACT CLASS 2).pdf

1、 MIL-PRF-39012/4F 14 August 2013 SUPERSEDING MIL-PRF-39012/4E 16 November 2006 PERFORMANCE SPECIFICATION SHEET CONNECTORS, COAXIAL, RADIO FREQUENCY (SERIES N (UNCABLED) RECEPTACLES JAM NUT AND FLANGE MOUNTED, SOCKET CONTACT, CLASS 2) This specification is approved for use by all Departments and Agen

2、cies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-PRF-39012. FIGURE 1. General configuration. AMSC N/A FSC 5935 INCH-POUND -X002 -X001 Provided by IHSNot for ResaleNo reproduction or networking permitted w

3、ithout license from IHS-,-,-MIL-PRF-39012/4F 2 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for information only. 3. See table I for dimensions A, B, C, and D. 4. Dimensions A and B are the largest overall dimensions of the receptacles except the flange height and width on das

4、h number 0002 or 7002. 5. All undimensioned pictorial configurations are for reference purposes only. 6. Receptacle dash number 0002 or 7002 not recommended for use on panels with greater than .071 (1.80 mm) max thickness. 7. Full threads to within .063 inch (1.60 mm) of shoulder; 1 1/2 max uneven t

5、hreads to shoulder. 8. There shall be a solid barrier in the socket between the pin entry and the solder pocket to prevent solder wicking. 9. Interface is a series N socket contact in accordance with MIL-STD-348. FIGURE 1. General configuration Continued. Inches mm Inches mm .022 0.56 .532 13.49 .11

6、0 2.79 .543 13.79 .120 3.05 .625 15.88 .130 3.30 .630 16.00 .250 6.35 .645 16.38 .354 8.99 .713 18.11 .364 9.25 .723 18.36 .492 12.50 .745 18.92 .503 12.78 .755 19.18 .526 13.36 .985 25.02 .531 13.49 1.005 25.53 -X003 Provided by IHSNot for ResaleNo reproduction or networking permitted without licen

7、se from IHS-,-,-MIL-PRF-39012/4F 3 TABLE I. Dash numbers, cross-reference, and dimensions. Dash number 1/ Type Dimension Inches (millimeters) 2/ Min Max 0001 3/ 7001 3/ Bulkhead (front mounted hermetic sealed) A B C D - - 1.125 (25.40) .702 (17.83) 1.750 (44.45) .885 (22.48) 1.250 (31.75) .721 (18.0

8、8) 0002 3/ 7002 3/ Flange (rear mounted) A B C D 1.062 (26.97) .620 (15.65) .721 (18.31) .075 (1.91) 1.156 (26.36) .670 (17.02) .751 (19.08) .085 (2.16) 0003 3/ 7003 3/ Bulkhead (rear mounted) A B C - .850 (21.59) .912 (23.16) 1.343 (34.11) .900 (22.86) .940 (23.88) 1/ For cross-reference of dash nu

9、mber to superseded Part or Identifying Number (PIN) or type designation, see table III. 2/ Dimensions are in inches. Metric equivalents are given for information only. 3/ These connectors have captivated center contacts. ENGINEERING DATA: Nominal impedance: 50 ohms. Frequency range: 0 to 11 GHz. Vol

10、tage rating 1,000 volts rms maximum working voltage at sea level. 250 volts rms maximum at 70,000 feet (4.437 kPa). Temperature rating: -65C to +165C. REQUIREMENTS: Design and configuration: See figure 1. Force to engage and disengage: Longitudinal force: Not applicable. Torque: 6 inch-pounds (.68 N

11、m) maximum. Coupling proof torque: Not applicable. Inspection conditions: Coupling torque: 6 to 10 inch-pounds (.68 to 1.13 Nm). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-39012/4F 4 Mating characteristics: In accordance with MIL-STD-348

12、. Contact with spring members: Center contact (socket): Oversize test pin: .074 inch (1.88 mm), diameter minimum (nonclosed entry contacts only). Insertion depth: .125 inch (3.17 mm), minimum. Number of insertions: 1. Insertion force test: Steel test pin diameter .066 inch (1.68 mm), minimum. Test p

13、in finish: 16 microinches (0.406 m). Insertion force: 2 pounds (8.90 N) maximum. Withdrawal force test: Steel test pin diameter .063 inch (1.60 mm), maximum. Withdrawal force: 2 ounces (.56 N) minimum. Test pin finish: 16 microinches (0.406 m). Hermetic seal: Applicable to M39012/04-0001 and M39012/

14、04-7001. (Leakage shall not exceed 1 x 10-7cm3/s of tracer gas at atmospheric pressure) Leakage (pressurized connectors): Applicable to M39012/04-0001, M39012/04-0003, M39012/04-7001 and M39012/04-7003. The receptacle shall be mounted in its normal manner on a closed container with the mating end ca

15、pped. Container interior air pressure shall be 30 psi. Insulation resistance: Method 302 of MIL-STD-202, test condition B. 5,000 megohms minimum. Center contact retention: 6 pounds (26.69 N) minimum axial force. Corrosion (salt spray): Method 101 of MIL-STD-202. Voltage standing wave ratio (VSWR): N

16、ot applicable. Connector durability: 500 cycles minimum at 12 cycles/minute maximum. The connector shall meet the mating characteristics and force to engage and disengage requirements. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-39012/4F

17、5 Contact resistance: In milliohms maximum. Initial After environment Center contact: M39012/04-X001 4.0 5.0 Outer contact: M39012/04-0001 .2 Not applicable M39012/04-7001 .4 Not applicable Center contact: M39012/04-X002 1.0 1.5 M39012/04-X003 1.0 1.5 Outer contact: M39012/04-0002 .2 Not applicable

18、M39012/04-0003 .2 Not applicable M39012/04-7002 .4 Not applicable M39012/04-7003 .4 Not applicable Dielectric withstanding voltage: Method 301 of MIL-STD-202. 2,500 volts rms minimum at sea level. Vibration, high frequency: Method 204, test condition B, MIL-STD-202. Shock: Method 213 of MIL-STD-202,

19、 test condition I. Temperature cycling: Method 102, test condition C, MIL-STD-202 except high temperature shall be 85C. High temperature shall be 200C. Thermal shock: Method 107 of MIL-STD-202, test condition B, except high temperature shall be +85C. High temperature shall be +200C for connectors us

20、ing +200C cables (see table I and III). Moisture resistance: Method 106 of MIL-STD-202. No measurements at high humidity. Insulation resistance shall be at least 200 megohms within 5 minutes after removal from humidity. Corona level: Not applicable RF high potential withstanding voltage: Voltage and

21、 frequency: 1,500 volts rms at 5 MHz. Leakage current: Not applicable. Cable retention force: Not applicable. Coupling mechanism retention force: Not applicable. RF leakage: Not applicable. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-3901

22、2/4F 6 Insertion loss: Not applicable. Part or Identifying Number (PIN): M39012/04- (dash number from table I). CAUTION: THE “7000” SERIES OF DASH NUMBERS ALLOW FOR A NICKEL PLATED CONNECTOR BODY. A NICKEL PLATED BODY IS NOT FOR USE IN APPLICATIONS WHERE PASSIVE INTERMODULATION GENERATION (PIM) MAY

23、BE A CONCERN (http:/ Silver is the preferred plating option. Group qualification: See table II. Cross-reference information: See table III. TABLE II. Group qualification. 1/, 2/ Group Submission and qualification of any of the following connectors Qualifies the following connectors I M39012/04-X001

24、M39012/04-X001 II M39012/04-X002 M39012/04-X002 III M39012/04-X003 M39012/04-X003 1/ If a connector manufacturer produces a connector which meets all the requirements for two or more connector PIN (within the same series), the manufacturer may receive qualification approval for two or more connector

25、 PIN by qualifying the one connector. It is not necessary that such connectors be in the same group. Each connector, however, must be marked with its own appropriate PIN. For group qualification, the connectors must be of similar design. 2/ Connectors of the same body material and finish may only qu

26、alify connectors of the same body material and finish. TABLE III. Cross-reference of PINs. Preferred PIN Substitute for PIN or type designation 1/ M39012/04-0001 M39012/04-0002 M39012/04-0003 MS90531-680A UG-58/U - 1/ The superseded PIN or the type designation is for cross-reference only. Where a su

27、perseded PIN or type designation is not given, none was assigned or will be assigned. The PIN M39012/04-XXXX shall be used in all cases for marking and identifying the connector. Changes from previous issue. The margins of this specification are marked with vertical lines to indicate where changes f

28、rom the previous issue were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the margin

29、al notations and relationship to the last previous issue. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-39012/4F 7 Referenced documents. In addition to MIL-PRF-39012, this document references the following: MIL-STD-202 MIL-STD-348 CONCLUDIN

30、G MATERIAL Custodians: Preparing activity: Army CR DLA CC Navy EC Air Force 85 (Project 5935-2013-193) NASA NA DLA - CC Review activities: Army AR, AT, EA, MI Navy AS, MC, OS, SH Air Force 19, 99 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-