DLA MIL-PRF-39012 70 D-2011 CONNECTORS RECEPTACLE ELECTRICAL COAXIAL RADIO FREQUENCY SERIES SMB (CABLED PIN CONTACT JAMNUT MOUNTED REAR MOUNTED CLASS 2).pdf

1、INCH-POUND MIL-PRF-39012/70D 16 November 2011 SUPERSEDING MIL-PRF-39012/70C 18 January 2007 PERFORMANCE SPECIFICATION SHEET CONNECTORS, RECEPTACLE, ELECTRICAL, COAXIAL, RADIO FREQUENCY, SERIES SMB (CABLED, PIN CONTACT, JAMNUT MOUNTED, REAR MOUNTED, CLASS 2) This specification is approved for use by

2、all Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-PRF-39012. FIGURE 1. General configuration. AMSC N/A FSC 5935 Provided by IHSNot for ResaleNo reproduction or networking permitted

3、without license from IHS-,-,-MIL-PRF-39012/70D 2 Inches mm Inches mm .018 .023 .065 .074 .077 .079 .082 .096 .46 .58 1.65 1.88 1.96 2.01 2.08 2.44 .187 .190 .192 .197 .312 .320 .400 .440 4.75 4.83 4.88 5.00 7.92 8.13 10.16 11.18 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for

4、 information only. 3. For dimension A, see table I. 4. Dimension A defines the overall length of the connector when assembled to the cable. 5. Wrench flats are to accommodate standard wrench opening in accordance with FED-STD-H28, appendix 10. 6. Maximum overall diameter of the connector is .320 inc

5、h (8.13 mm). 7. All undimensioned pictorial configurations are for reference purposes only. 8. Series SMB, pin contact in accordance with MIL-STD-348. FIGURE 1. General configuration Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-

6、39012/70D 3 TABLE I. Dash numbers, cross-reference, and dimensions. Dash No. M39012/70- # Applicable cable group from MIL-PRF-39012, appendix B M17/ Typical mating Connector 1/ Dimensions Inches (millimeters) Maximum 2/ CATEGORY A FIELD SERVICEABLE (NO SPECIAL TOOLS REQUIRED) 0003 3/ 4/ Cable group

7、I 93-RG178 * 169-00001 % M39012/67-0003 M39012/69-0003 A .88 (22.35) 0004 3/ 4/ Cable group II 113-RG316 * 172-00001 % 94-RG179 M39012/67-0004 M39012/69-0004 0103 3/ Cable group I 93-RG178 * 169-00001 % M39012/67-0103 M39012/69-0103 0104 3/ Cable group II 113-RG316 * 172-00001 % 94-RG179 M39012/67-0

8、104 M39012/69-0104 4101 3/ Cable group I 93-RG178 * 169-00001 % M39012/67-4101 M39012/69-4101 4102 3/ Cable group II 113-RG316 * 172-00001 % 94-RG179 M39012/67-4102 M39012/69-4102 CATEGORY C FIELD REPLACEABLE (MIL-C-22520/5 BASIC CRIMP TOOL) 5/ 0011 3/ 4/ Cable group I 93-RG178 * 169-00001 % M39012/

9、67-0011 M39012/69-0011 A 1.20 (30.48) 0012 3/ 4/ Cable group IIa Example: M39012/68-3001 mates with M39012/67-3001, and M39012/68-4001 mates with M39012/67-4001. NOT FOR ARMY, NAVY, OR AIR FORCE USE. FOR OEM USE ONLY Provided by IHSNot for ResaleNo reproduction or networking permitted without licens

10、e from IHS-,-,-MIL-PRF-39012/70D 10 TABLE V. Group qualification and retention testing. Group Submission and retention of Qualification of any of the following connectors 1/ M39012/ Qualifies the following connectors M39012/ I 68-0003 70-0003 68-0003 68-0103 2/ 70-0003 70-0103 2/ II 68-0004 70-0004

11、68-0004 68-0104 2/ 70-0004 70-0104 2/ III 68B0008 70B0008 68B0008 68B0013 2/ 70B0008 70B0013 2/ IV 68B0009 70B0009 68B0009 68B0010 68B0014 2/ 68B0015 2/ 70B0009 70B0010 70B0014 2/ 70B0015 2/ V 68B0010 70B0010 68B0010 68B0015 70B0010 70B0015 2/ VI 68-0011 70-0011 68-0011 68-0016 70-0011 70-0016 2/ VI

12、I 68-0012 70-0012 68-0012 68-0017 70-0012 70-0017 2/ 1/ Individual connectors other than listed are self qualifying only. 2/ Corrosion and contact resistance test data must be submitted to DSCC-VQ before qualification approval may be granted. NOTES: 1. If a connector manufacturer produces a connecto

13、r which meets all the requirements for two or more connector PINs (within the same series), the manufacturer may receive qualification approval for two or more connector PINs by qualifying the one connector. It is not necessary that such connectors be in the same group. Each connector, however, must

14、 be marked with its own appropriate PIN. For group qualification, the connectors must be of similar design. 2. For qualification retention, where more than one part is listed in a group in this column, data may be supplied on any of those parts in order to retain qualification for those parts in the

15、 corresponding right-hand column. The part does not necessarily have to be the part initially qualified. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-39012/70D 11 TABLE VI. Cross reference of PIN. Preferred PIN M39012/70 Substitute for PIN

16、 or type designation -0003 -0004 B0008 B0009 B0010 M39012/70-0001 M39012/70-0002 M39012/70-0008, M39012/70-0005 M39012/70-0009, M39012/70-0006 M39012/70-0010, M39012/70-0007 Changes from previous issue. The margins of this specification are marked with vertical lines to indicate where changes from t

17、he previous issue were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal no

18、tations and relationship to the last previous issue. Referenced documents. In addition to MIL-PRF-39012, this document references the following: MIL-STD-348 MIL-DTL-22520 MIL-C-22520/5 MIL-STD-202 FED-STD-H28 ASTM B488 CONCLUDING MATERIAL Custodians: Preparing activity: Army - CR DLA - CC Navy - EC

19、Air Force - 85 (Project 5935-2009-105) NASA - NA DLA - CC Review activities: Army - AT, AV, EA MI Navy - AS, MC, OS, SH Air Force - 19, 99 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-