DLA MIL-PRF-39022 10 B-2008 CAPACITORS FIXED METALLIZED PAPER-PLASTIC FILM DIELECTRIC DIRECT CURRENT (HERMETICALLY SEALED IN METAL CASES) ESTABLISHED RELIABILITY STYLE CHR10 (INSUL.pdf

1、AMSC N/A FSC 5910 INCH-POUND MIL-PRF-39022/10B 5 November 2008 SUPERSEDING MIL-PRF-39022/10A 25 May 2001 PERFORMANCE SPECIFICATION SHEET CAPACITORS, FIXED, METALLIZED, PAPER-PLASTIC FILM DIELECTRIC, DIRECT CURRENT (HERMETICALLY SEALED IN METAL CASES) ESTABLISHED RELIABILITY, STYLE CHR10 (INSULATED)

2、This specification sheet is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-PRF-39022. NOTES: 1. Number 24 AWG wire (.020 .002 inch (0.51 0.05 mm) for case dia

3、meters of .175 inch (4.45 mm) and .195 (4.95 mm). Number 22 AWG wire (.025 .002 inch (0.64 0.05 mm) for case diameters of .235 inch (5.97 mm) and .312 (7.92 mm). Number 20 AWG wire (.032 inch .002 inch (0.81 0.05 mm) for case diameters of .400 inch (10.16 mm) and over (see table I for exceptions.) N

4、umber 18 AWG wire (.040 inches .002 inch): See table I. 2. See table I for additional dimensions. 3. Dimensions are in inches. 4. Metric equivalents (to the nearest 0.01 mm) are given for general information only. 5. Insulating sleeve shall extend beyond the capacitor body but shall not exceed .031

5、inch (0.79 mm) on either end. Insulating sleeve thickness shall not exceed .016 inch (0.41 mm). 6. Plastic insulating sleeve shall be transparent; marking shall be placed on the capacitor case. 7. Metric equivalents are in parentheses. 8. Lead length may be a minimum of one inch long for use in tape

6、 and reel packaging, when specified in the ordering data. FIGURE 1. Dimensions and configuration. INACTIVE FOR NEW DESIGN AFTER 25 MAY 2001Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-39022/10B 2 REQUIREMENTS: Dimensions and configuration:

7、 See figure 1 and table I. Case material: Nonmagnetic (end seals may be of magnetic material). Capacitance value: See table I. Capacitance tolerance: F (1 percent), G (2 percent), J (5 percent), and K (10 percent). Rated voltage: See table I for 85C rating; derate to 60 percent of 85C rating for ope

8、ration at 125C. Dielectric material: Polycarbonate. Operating temperature range: -55C to +125C. Failure rate level: M (1.0 percent), P (0.1 percent), R (0.01 percent), and S (0.001 percent). Thermal shock: Method 107 of MIL-STD-202, condition A, except step 3 shall be +125C +4C, -0C. Radiographic in

9、spection (X-ray): Method 209 of MIL-STD-202. (Required for FR levels R and S only.) DC burn-in: In accordance with MIL-PRF-39022, table VI, qualification inspection, group I and table VII, group A inspection, subgroup 1, except 140 percent minimum of dc rated voltage shall be applied for 48 hours mi

10、nimum at +125C +4C, -0C. 100 percent inspection required. Seal: Method 112 of MIL-STD-202, condition A or test condition D with no evidence of leakage. For liquid impregnant capacitors, the alternative seal test in MIL-PRF-39022 may be used with a temperature of +125C +4C, -0C and length of test of

11、1 hour. Dielectric withstanding voltage (DWV): Method 301 of MIL-STD-202; 100 percent inspection required following dc burn-in. Terminal to terminal: AC: 100 10 Hz square wave, peak-to-peak voltage, three times dc rated voltage for 60 seconds minimum, but need not exceed 800 V peak-to-peak. Square w

12、ave signal shall have a rise time of 10 to 100 microseconds and a maximum overshoot of 20 percent of rated peak voltage. DC: 200 percent of dc rated voltage for 60 seconds, minimum. Terminals to case (when case is not a terminal): Same requirements as specified for terminal to terminal dc DWV test.

13、Insulation resistance (IR): Method 302 of MIL-STD-202. Terminal to terminal: See table III. Terminal to case (when case is not a terminal): 50,000 megohms, minimum. Capacitance: Method 305 of MIL-STD-202. Dissipation factor (DF): At 25C: 0.25 percent maximum. At 85C: 0.40 percent maximum. At 125C: 0

14、.60 percent maximum. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-39022/10B 3 TABLE I. Capacitor characteristics and dimensions. Part or Identifying DC rated Capacitance Dimensions, nominal 3/ 4/ 5/ Number (PIN) 1/ voltage value in F D +.0

15、15, -.005 L .031 M39022/10-473- 50 .047 .174 .531 M39022/10-563- 50 .056 .174 .531 M39022/10-683- 50 .068 .174 .625 M39022/10-823- 50 .082 .174 .625 M39022/10-104- 50 .10 .174 .625 M39022/10-124- 50 .12 .174 .625 M39022/10-154- 50 .15 .193 .625 M39022/10-184- 50 .18 .193 .625 M39022/10-224- 50 .22 .

16、235 .625 M39022/10-274- 50 .27 .235 .625 M39022/10-334- 50 .33 .312 .625 M39022/10-394- 50 .39 .312 .625 M39022/10-474- 50 .47 .312 .625 M39022/10-564- 50 .56 .312 .625 M39022/10-684- 50 .68 .312 .843 M39022/10-824- 50 .82 .312 .843 M39022/10-105- 50 1.0 .312 .843 M39022/10-125- 50 1.2 .400 .843 M39

17、022/10-155- 50 1.5 .400 .843 M39022/10-185- 50 1.8 .400 .843 M39022/10-205- 50 2.0 .400 .843 M39022/10-225- 50 2.2 .400 1.125 M39022/10-275- 50 2.7 .400 1.125 M39022/10-305- 50 3.0 .400 1.125 M39022/10-335- 50 3.3 .400 1.125 M39022/10-395- 50 3.9 .500 1.125 M39022/10-475- 50 4.7 .500 1.125 M39022/10

18、-505- 50 5.0 .500 1.125 M39022/10-565- 50 5.6 .500 1.125 M39022/10-685- 50 6.8 .562 1.125 M39022/10-825- 50 8.2 .562 1.312 M39022/10-106- 50 10.0 .670 1.312 M39022/10-126- 50 12.0 .670 1.312 M39022/10-156- 50 15.0 .750 1.375 M39022/10-186- 50 18.0 .750 1.375 M39022/10-206- 50 20.0 .750 1.625 M39022/

19、10-226- 50 22.0 .750 1.625 M39022/10-103- 100 .01 .174 .625 M39022/10-123- 100 .012 .174 .625 M39022/10-153- 100 .015 .174 .625 M39022/10-183- 100 .018 .174 .625 M39022/10-223- 100 .022 .174 .625 M39022/10-273- 100 .027 .174 .625 M39022/10-333- 100 .033 .174 .625 M39022/10-393- 100 .039 .174 .625 M3

20、9022/10-473- 100 .047 .193 .625 M39022/10-563- 100 .056 .193 .625 M39022/10-683- 100 .068 .235 .625 M39022/10-823- 100 .082 .235 .625 M39022/10-104- 100 .10 .235 .688 M39022/10-124- 100 .12 .235 .688 See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted

21、without license from IHS-,-,-MIL-PRF-39022/10B 4 TABLE I. Capacitor characteristics and dimensions. Continued. Part or Identifying DC rated Capacitance Dimensions, nominal 3/ 4/ 5/ Number (PIN) 1/ voltage value in F D +.015, -.005 L .031 M39022/10-154- 100 .15 .312 .625 M39022/10-184- 100 .18 .312 .

22、625 M39022/10-224- 100 .22 .312 .688 M39022/10-274- 100 .27 .312 .688 M39022/10-334- 100 .33 .312 .812 M39022/10-394- 100 .39 .312 .812 M39022/10-474- 100 .47 .400 .688 M39022/10-564- 100 .56 .400 .812 M39022/10-684- 100 .68 .400 .812 M39022/10-824- 100 .82 .400 .938 M39022/10-105- 100 1.0 .400 .938

23、 M39022/10-125- 100 1.2 .500 .938 M39022/10-155- 100 1.5 .500 .938 M39022/10-185- 100 1.8 .500 1.125 M39022/10-205- 100 2.0 .500 1.125 M39022/10-225- 100 2.2 .500 1.125 M39022/10-275- 100 2.7 .562 1.312 M39022/10-305- 100 3.0 .562 1.312 M39022/10-335- 100 3.3 .562 1.312 M39022/10-405- 100 4.0 .562 1

24、.562 M39022/10-475- 100 4.7 .670 1.312 M39022/10-505- 100 5.0 .670 1.312 M39022/10-565- 100 5.6 .670 1.312 M39022/10-685- 100 6.8 .670 1.562 M39022/10-825- 100 8.2 .670 1.812 M39022/10-106- 100 10.0 .750 1.812 M39022/10-126- 100 12.0 .750 1.812 M39022/10-156- 100 15.0 1.000 2/ 1.875 M39022/10-186- 1

25、00 18.0 1.000 2/ 1.875 M39022/10-206- 100 20.0 1.000 2/ 1.875 M39022/10-226- 100 22.0 1.000 2/ 1.875 M39022/10-103- 200 .01 .174 .625 M39022/10-123- 200 .012 .174 .625 M39022/10-153- 200 .015 .174 .625 M39022/10-183- 200 .018 .193 .625 M39022/10-223- 200 .022 .193 .625 M39022/10-273- 200 .027 .235 .

26、625 M39022/10-333- 200 .033 .235 .625 M39022/10-393- 200 .039 .235 .688 M39022/10-473- 200 .047 .235 .688 M39022/10-563- 200 .056 .312 .625 M39022/10-683- 200 .068 .312 .625 M39022/10-823- 200 .082 .312 .688 M39022/10-104- 200 .10 .312 .688 M39022/10-124- 200 .12 .312 .812 M39022/10-154- 200 .15 .31

27、2 .812 M39022/10-184- 200 .18 .400 .688 M39022/10-224- 200 .22 .400 .812 M39022/10-274- 200 .27 .400 .812 M39022/10-334- 200 .33 .400 .938 See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-39022/10B 5 TABLE I. Cap

28、acitor characteristics and dimensions. Continued. Part or Identifying DC rated Capacitance Dimensions, nominal 3/ 4/ 5/ Number (PIN) 1/ voltage value in F D +.015, -.005 L .031 M39022/10-394- 200 .39 .400 .938 M39022/10-474- 200 .47 .400 1.125 M39022/10-564- 200 .56 .400 1.312 M39022/10-684- 200 .68

29、 .500 1.125 M39022/10-824- 200 .82 .500 1.125 M39022/10-105- 200 1.0 .562 1.125 M39022/10-125- 200 1.2 .562 1.312 M39022/10-155- 200 1.5 .562 1.312 M39022/10-185- 200 1.8 .562 1.812 M39022/10-205- 200 2.0 .562 1.812 M39022/10-225- 200 2.2 .562 1.812 M39022/10-275- 200 2.7 .670 1.562 M39022/10-305- 2

30、00 3.0 .750 1.562 M39022/10-335- 200 3.3 .750 1.812 M39022/10-405- 200 4.0 .750 1.812 M39022/10-475- 200 4.7 .750 2.062 M39022/10-505- 200 5.0 .750 2.062 M39022/10-565- 200 5.6 .750 2.312 M39022/10-605- 200 6.0 .750 2.312 M39022/10-705- 200 7.0 1.000 1.812 M39022/10-825- 200 8.2 1.000 2/ 2.062 M3902

31、2/10-106- 200 10.0 1.000 2/ 2.312 M39022/10-103- 300 .01 .193 .688 M39022/10-123- 300 .012 .235 .688 M39022/10-153- 300 .015 .235 .688 M39022/10-183- 300 .018 .235 .812 M39022/10-223- 300 .022 .235 .812 M39022/10-273- 300 .027 .312 .688 M39022/10-333- 300 .033 .312 .688 M39022/10-393- 300 .039 .312

32、.812 M39022/10-473- 300 .047 .312 .812 M39022/10-563- 300 .056 .312 .938 M39022/10-683- 300 .068 .312 .938 M39022/10-823- 300 .082 .400 .812 M39022/10-104- 300 .10 .400 .938 M39022/10-124- 300 .12 .400 .938 M39022/10-154- 300 .15 .400 1.125 M39022/10-184- 300 .18 .400 1.312 M39022/10-224- 300 .22 .4

33、00 1.312 M39022/10-274- 300 .27 .562 1.125 M39022/10-334- 300 .33 .562 1.125 M39022/10-394- 300 .39 .562 1.125 M39022/10-474- 300 .47 .562 1.562 M39022/10-564- 300 .56 .562 1.562 M39022/10-684- 300 .68 .670 1.312 M39022/10-824- 300 .82 .670 1.562 M39022/10-105- 300 1.0 .670 1.812 M39022/10-125- 300

34、1.2 .670 1.812 M39022/10-155- 300 1.5 .750 2.062 M39022/10-185- 300 1.8 .750 2.062 See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-39022/10B 6 TABLE I. Capacitor characteristics and dimensions. Continued. Part o

35、r Identifying DC rated Capacitance Dimensions, nominal 3/ 4/ 5/ Number (PIN) 1/ voltage value in F D +.015, -.005 L .031 M39022/10-205- 300 2.0 .750 2.312 M39022/10-225- 300 2.2 1.000 1.812 M39022/10-255- 300 2.5 1.000 1.812 M39022/10-275- 300 2.7 1.000 1.812 M39022/10-305- 300 3.0 1.000 2.062 M3902

36、2/10-335- 300 3.3 1.000 2.312 M39022/10-395- 300 3.9 1.000 2.562 M39022/10-103- 400 .01 .235 .688 M39022/10-123- 400 .012 .235 .812 M39022/10-153- 400 .015 .235 .812 M39022/10-183- 400 .018 .235 .812 M39022/10-223- 400 .022 .312 .688 M39022/10-273- 400 .027 .312 .812 M39022/10-333- 400 .033 .312 .81

37、2 M39022/10-393- 400 .039 .312 .938 M39022/10-473- 400 .047 .400 .812 M39022/10-563- 400 .056 .400 .812 M39022/10-683- 400 .068 .400 .938 M39022/10-823- 400 .082 .400 .938 M39022/10-104- 400 .10 .400 1.125 M39022/10-124- 400 .12 .400 1.312 M39022/10-154- 400 .15 .400 1.312 M39022/10-184- 400 .18 .56

38、2 1.125 M39022/10-224- 400 .22 .562 1.125 M39022/10-274- 400 .27 .562 1.312 M39022/10-334- 400 .33 .562 1.562 M39022/10-394- 400 .39 .562 1.562 M39022/10-474- 400 .47 .562 1.812 M39022/10-564- 400 .56 .670 1.562 M39022/10-684- 400 .68 .670 1.812 M39022/10-824- 400 .82 .750 1.812 M39022/10-105- 400 1

39、.0 .750 2.062 M39022/10-125- 400 1.2 1.000 1.812 M39022/10-155- 400 1.5 1.000 1.812 M39022/10-185- 400 1.8 1.000 2.062 M39022/10-205- 400 2.0 1.000 2.062 M39022/10-225- 400 2.2 1.000 2.312 M39022/10-255- 400 2.5 1.000 2.562 M39022/10-275- 400 2.7 1.000 2.562 M39022/10-103- 600 .01 .312 .812 M39022/1

40、0-123- 600 .012 .312 .812 M39022/10-153- 600 .015 .400 .812 M39022/10-183- 600 .018 .400 .812 M39022/10-223- 600 .022 .400 .812 M39022/10-273- 600 .027 .400 .937 M39022/10-333- 600 .033 .400 .937 M39022/10-393- 600 .039 .400 1.125 M39022/10-473- 600 .047 .400 1.125 M39022/10-563- 600 .056 .400 1.312

41、 M39022/10-683- 600 .068 .400 1.312 See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-39022/10B 7 TABLE I. Capacitor characteristics and dimensions. Continued. Part or Identifying DC rated Capacitance Dimensions,

42、nominal 3/ 4/ 5/ Number (PIN) 1/ voltage value in F D +.015, -.005 L .031 M39022/10-823- 600 .082 .562 1.125 M39022/10-104- 600 .10 .562 1.125 M39022/10-124- 600 .12 .562 1.312 M39022/10-154- 600 .15 .562 1.312 M39022/10-184- 600 .18 .562 1.562 M39022/10-224- 600 .22 .562 1.812 M39022/10-274- 600 .2

43、7 .670 1.562 M39022/10-334- 600 .33 .670 1.812 M39022/10-394- 600 .39 .670 1.812 M39022/10-474- 600 .47 .750 1.812 M39022/10-564- 600 .56 .750 2.062 M39022/10-684- 600 .68 .750 2.312 M39022/10-824- 600 .82 1.000 1.812 M39022/10-105- 600 1.0 1.000 2.062 1/ The complete PIN will include additional sym

44、bols to indicate circuit and voltage code (see table IV), capacitance tolerance (K, J, G, or F), and FRL (M, P, R, or S). 2/ Uses #18 AWG leads. 3/ Dimensions are for bare case sizes (see figure 1). 4/ Dimensions are for circuit 1. For circuit 3, deduct .062 inches (1.57 mm) from length (see figure

45、1). 5/ See table II for metric equivalents. TABLE II. Metric equivalents of decimal inches. 1/ Inches mm Inches mm Inches mm .005 .015 .031 .174 .193 .235 .312 .400 .500 .531 .562 0.13 0.38 0.79 4.42 4.90 5.97 7.92 10.16 12.70 13.49 14.27 .625 .670 .688 .750 .812 .843 .874 .937 .938 1.000 1.062 15.8

46、8 17.02 17.48 19.05 20.62 21.41 22.20 23.80 23.83 25.40 26.97 1.125 1.312 1.375 1.562 1.625 1.812 1.875 2,062 2.124 2.312 2.562 28.58 33.32 34.93 39.67 41.28 46.02 47.63 52.37 53.95 58.72 65.07 1/ Metric equivalents (to the nearest 0.01 millimeter) are given for general information only. TABLE III.

47、Insulation resistance. In megohms: At 25C 3C (need not exceed) At 85C +4C, -0C (need not exceed) At 125C +4C, -0C (need not exceed) 250,000 25,000 15,000 In megohms x microfarads (minimum): At 25C 3C At 85C +4C, -0C At 125C +4C, -0C 100,000 6,000 1,000 Provided by IHSNot for ResaleNo reproduction or

48、 networking permitted without license from IHS-,-,-MIL-PRF-39022/10B 8 Barometric pressure (reduced): Method 105 of MIL-STD-202, condition D (100,000 feet). 125 percent of rated voltage applied. See MIL-PRF-39022 for voltage limitations. Vibration, high frequency: Method 204 of MIL-STD-202, condition D (20 G). 50 percent of rated voltage applied. Salt atmosphere (corrosion): Method 101 of MIL-STD-202, c