DLA MIL-PRF-39022 2 G-2011 CAPACITORS FIXED METALLIZED PAPER-PLASTIC FILM DIELECTRIC DIRECT CURRENT (HERMETICALLY SEALED IN METAL CASES) ESTABLISHED RELIABILITY STYLE CHR19 (INSULA.pdf

1、AMSC N/A FSC 5910 INCH-POUND MIL-PRF-39022/2G 24 October 2011 SUPERSEDING MIL-PRF-39022/2F 30 June 2006 PERFORMANCE SPECIFICATION SHEET CAPACITORS, FIXED, METALLIZED, PAPER-PLASTIC FILM DIELECTRIC, DIRECT CURRENT, (HERMETICALLY SEALED IN METAL CASES), ESTABLISHED RELIABILITY, STYLE CHR19 (INSULATED)

2、 This specification sheet is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-PRF-39022. NOTES: 1. Number 22 AWG wire .025 .002 inch (0.64 0.05 mm) for case dia

3、meters of .235 inch (5.97 mm) and .312 inch (7.92 mm). Number 20 AWG wire .032 .002 inch (0.81 0.05 mm) for case diameters of .400 inch (10.16 mm) and over. 2. See table I for additional dimensions. 3. Dimensions are in inches. 4. Metric equivalents are given for general information only. 5. Insulat

4、ing sleeve shall extend beyond the capacitor body but shall not exceed .031 inch (0.79 mm) on either end. Insulating sleeve thickness shall not exceed .016 inch (0.41 mm). 6. Plastic insulating sleeve shall be transparent; marking shall be applied to the capacitor case. 7. Metric equivalents are in

5、parentheses. 8. Lead length may be a minimum of one inch (25.4 mm) long for use in tape and reel packaging when specified in the ordering data. FIGURE 1. Dimensions and configuration. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-39022/2G 2

6、 REQUIREMENTS: Dimensions and configuration: See figure 1 and table I. Case material: Nonmagnetic (end seal may be of magnetic material). Capacitance value: See table I. Capacitance tolerance: 5 percent and 10 percent. Rated voltage: See table I. Dielectric material: Normally paper-polyethylene-tere

7、phthalate. Operating temperature range: -55C to +125C. Failure rate level (%/1000 hours): M (1.0), P (0.1), R (0.01), and S (0.001). Radiographic inspection (X-ray): Method 209 of MIL-STD-202. Thermal shock: Method 107 of MIL-STD-202, condition A, except step 3 shall be +125C +4C, -0C. Seal: Method

8、112 of MIL-STD-202, condition A, or (for liquid-filled units only) 1 hour at +125C +4C, -0C with no evidence of leakage. Dielectric withstanding voltage (DWV): Method 301 of MIL-STD-202. Terminal to terminal: 200 percent of rated voltage. Terminals to case (when case is not a terminal): 200 percent

9、of rated voltage. For 100 percent inspection: 250 percent of rated voltage for not less than 5 seconds, or 200 percent of rated voltage for not less than 15 seconds. Insulation resistance (IR): Method 302 of MIL-STD-202. Terminal to terminal: See table II. Terminal to case (when case is not a termin

10、al): 10,000 megohms, minimum. Capacitance: Method 305 of MIL-STD-202. Dissipation factor (DF): 1 percent. Barometric pressure (reduced): Method 105 of MIL-STD-202, condition D (100,000 feet). 125 percent of rated voltage applied: See MIL-PRF-39022 for voltage limitations. Vibration, high frequency:

11、Method 204 of MIL-STD-202, condition D (20 gs peak). 50 percent of rated voltage applied. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-39022/2G 3 TABLE I. Electrical characteristics, dimensions, and dash numbers. DC rated voltage (Volts) C

12、apacitance value (F) Circuit diagram Capacitance tolerance (Percent ) Dimension, nominal (inches) 1/ 2/ Dash number Failure rate level (%/1,000 hr) L 0.062 D 0.031 M(1.0) P(0.1) R(0.01) S(0.001) 200 200 200 200 200 200 200 200 200 200 200 200 200 200 200 200 200 200 200 200 200 200 200 200 200 200 2

13、00 200 200 200 200 200 200 200 200 200 200 200 200 200 200 200 200 200 200 200 200 200 200 200 200 200 200 200 0.10 0.10 0.10 0.10 0.15 0.15 0.15 0.15 0.22 0.22 0.22 0.22 0.33 0.33 0.33 0.33 0.47 0.47 0.47 0.47 0.68 0.68 0.68 0.68 1.0 1.0 1.0 1.0 1.5 1.5 1.5 1.5 2.0 2.0 2.0 2.0 3.0 3.0 3.0 3.0 4.3 4

14、.3 4.3 4.3 5.1 5.1 5.1 5.1 6.2 6.2 6.2 6.2 8.2 8.2 1 1 3 3 1 1 3 3 1 1 3 3 1 1 3 3 1 1 3 3 1 1 3 3 1 1 3 3 1 1 3 3 1 1 3 3 1 1 3 3 1 1 3 3 1 1 3 3 1 1 3 3 1 1 5 10 5 10 5 10 5 10 5 10 5 10 5 10 5 10 5 10 5 10 5 10 5 10 5 10 5 10 5 10 5 10 5 10 5 10 5 10 5 10 5 10 5 10 5 10 5 10 5 10 5 10 5 10 1.125

15、1.125 1.062 1.062 1.125 1.125 1.062 1.062 1.125 1.125 1.062 1.062 1.125 1.125 1.062 1.062 1.125 1.125 1.062 1.062 1.375 1.375 1.312 1.312 1.625 1.625 1.562 1.562 1.844 1.844 1.781 1.781 1.844 1.844 1.781 1.781 2.125 2.125 2.062 2.062 2.625 2.625 2.562 2.562 1.875 1.875 1.812 1.812 2.125 2.125 2.062

16、2.062 2.625 2.625 .312 .312 .312 .312 .312 .312 .312 .312 .400 .400 .400 .400 .500 .500 .500 .500 .500 .500 .500 .500 .562 .562 .562 .562 .562 .562 .562 .562 .562 .562 .562 .562 .672 .672 .672 .672 .750 .750 .750 .750 .750 .750 .750 .750 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 11

17、11 1112 1113 1114 1115 1116 1117 1118 1119 1120 1121 1122 1123 1124 1125 1126 1127 1128 1129 1130 1131 1132 1133 1134 1135 1136 1137 1138 1139 1140 1141 1142 1143 1144 1145 1146 1147 1148 1149 1150 1151 1152 1153 1154 1155 1156 1157 1158 1159 1160 1161 1162 1163 1164 1221 1222 1223 1224 1225 1226 12

18、27 1228 1229 1230 1231 1232 1233 1234 1235 1236 1237 1238 1239 1240 1241 1242 1243 1244 1245 1246 1247 1248 1249 1250 1251 1252 1253 1254 1255 1256 1257 1258 1259 1260 1261 1262 1263 1264 1265 1266 1267 1268 1269 1270 1271 1272 1273 1274 1331 1332 1333 1334 1335 1336 1337 1338 1339 1340 1341 1342 13

19、43 1344 1345 1346 1347 1348 1349 1350 1351 1352 1353 1354 1355 1356 1357 1358 1359 1360 1361 1362 1363 1364 1365 1366 1367 1368 1369 1370 1371 1372 1373 1374 1375 1376 1377 1378 1379 1380 1381 1382 1383 1384 1441 1442 1443 1444 1445 1446 1447 1448 1449 1450 1451 1452 1453 1454 1455 1456 1457 1458 14

20、59 1460 1461 1462 1463 1464 1465 1466 1467 1468 1469 1470 1471 1472 1473 1474 1475 1476 1477 1478 1479 1480 1481 1482 1483 1484 1485 1486 1487 1488 1489 1490 1491 1492 1493 1494 See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from I

21、HS-,-,-MIL-PRF-39022/2G 4 TABLE I. Electrical characteristics, dimensions, and dash numbers - Continued. DC rated voltage (Volts) Capacitance value (F) Circuit diagram Capacitance tolerance (Percent ) Dimension, nominal (inches) 1/ 2/ Dash number Failure rate level (%/1,000 hr) L 0.062 D 0.031 M(1.0

22、) P(0.1) R(0.01) S(0.001) 200 200 400 400 400 400 400 400 400 400 400 400 400 400 400 400 400 400 400 400 400 400 400 400 400 400 400 400 400 400 400 400 400 400 400 400 400 400 400 400 400 400 400 400 400 400 400 400 400 400 8.2 8.2 0.047 0.047 0.047 0.047 0.068 0.068 0.068 0.068 0.1 0.1 0.1 0.1 0.

23、15 0.15 0.15 0.15 0.22 0.22 0.22 0.22 0.33 0.33 0.33 0.33 0.47 0.47 0.47 0.47 0.68 0.68 0.68 0.68 1.0 1.0 1.0 1.0 1.5 1.5 1.5 1.5 2.2 2.2 2.2 2.2 3.3 3.3 3.3 3.3 3 3 1 1 3 3 1 1 3 3 1 1 3 3 1 1 3 3 1 1 3 3 1 1 3 3 1 1 3 3 1 1 3 3 1 1 3 3 1 1 3 3 1 1 3 3 1 1 3 3 5 10 5 10 5 10 5 10 5 10 5 10 5 10 5 1

24、0 5 10 5 10 5 10 5 10 5 10 5 10 5 10 5 10 5 10 5 10 5 10 5 10 5 10 5 10 5 10 5 10 5 10 2.562 2.562 1.125 1.125 1.062 1.062 1.125 1.125 1.062 1.062 1.125 1.125 1.062 1.062 1.125 1.125 1.062 1.062 1.375 1.375 1.312 1.312 1.375 1.375 1.312 1.312 1.625 1.625 1.562 1.562 1.625 1.625 1.562 1.562 1.875 1.8

25、75 1.812 1.812 1.625 1.625 1.562 1.562 2.125 2.125 2.062 2.062 2.625 2.625 2.562 2.562 1.000 1.000 .400 .400 .400 .400 .400 .400 .400 .400 .500 .500 .500 .500 .562 .562 .562 .562 .562 .562 .562 .562 .672 .672 .672 .672 .672 .672 .672 .672 .750 .750 .750 .750 .750 .750 .750 .750 1.000 1.000 1.000 1.0

26、00 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1165 1166 1167 1168 1169 1170 1171 1172 1173 1174 1175 1176 1177 1178 1179 1180 1181 1182 1183 1184 1185 1186 1187 1188 1189 1190 1191 1192 1193 1194 1195 1196 1197 1198 1199 1200 1201 1202 1203 1204 1205 1206 1207 1208 1209 1210 1211 1212 1213 1214

27、 1275 1276 1277 1278 1279 1280 1281 1282 1283 1284 1285 1286 1287 1288 1289 1290 1291 1292 1293 1294 1295 1296 1297 1298 1299 1300 1301 1302 1303 1304 1305 1306 1307 1308 1309 1310 1311 1312 1313 1314 1315 1316 1317 1318 1319 1320 1321 1322 1323 1324 1385 1386 1387 1388 1389 1390 1391 1392 1393 1394

28、 1395 1396 1397 1398 1399 1400 1401 1402 1403 1404 1405 1406 1407 1408 1409 1410 1411 1412 1413 1414 1415 1416 1417 1418 1419 1420 1421 1422 1423 1424 1425 1426 1427 1428 1429 1430 1431 1432 1433 1434 1495 1496 1497 1498 1499 1500 1501 1502 1503 1504 1505 1506 1507 1508 1509 1510 1511 1512 1513 1514

29、 1515 1516 1517 1518 1519 1520 1521 1522 1523 1524 1525 1526 1527 1528 1529 1530 1531 1532 1533 1534 1535 1536 1537 1538 1539 1540 1541 1542 1543 1544 1/ Dimensions shown are bare case sizes (see figure 1). 2/ Metric equivalents, see table III. Provided by IHSNot for ResaleNo reproduction or network

30、ing permitted without license from IHS-,-,-MIL-PRF-39022/2G 5 TABLE II. Insulation resistance. At dc voltage of 200 V 400 V In megohms: At +25C 3C (need not exceed) At +125C +4C, -0C (need not exceed) 12,000 150 12,000 600 In megohms x microfarads (minimum): At +25C 3C At +125C +4C, -0C 2,000 10 2,0

31、00 40 TABLE III. Metric equivalents of decimal inches. 1/ Inches mm Inches mm Inches mm .031 .062 .312 .400 .500 .562 .672 .750 0.79 1.57 7.92 10.16 12.70 14.27 17.07 19.05 1.000 1.062 1.125 1.312 1.375 1.562 1.625 1.781 25.40 26.97 28.58 33.32 34.93 39.67 41.28 45.24 1.812 1.844 1.875 2.062 2.125 2

32、.562 2.625 46.02 46.84 47.63 52.37 53.98 65.07 66.68 1/ Metric equivalents are given for general information only. Salt atmosphere (corrosion): Method 101 of MIL-STD-202, condition B (48 hours). Salt solution: 5 percent. Moisture resistance: Method 106 of MIL-STD-202. Immersion: Method 104 of MIL-ST

33、D-202, condition C. DWV: Insulating sleeves: Greater than 4,000 volts, dc. Terminal to terminal: 200 percent of rated voltage. Terminals to case (when case is not a terminal): 200 percent of rated voltage. IR: Insulating sleeves: 100 megohms, minimum. Terminal to terminal: Not less than 50 percent o

34、f value specified in table II. Terminals to case (when case is not a terminal): 5,000 megohms, minimum. Capacitance: Within 10 percent of initial value. DF: Not more than 1.1 percent. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-39022/2G 6

35、 Solderability: Method 208 of MIL-STD-202. Shock (specified pulse): Method 213 of MIL-STD-202, condition I. 50 percent of rated voltage applied. DWV, IR, Capacitance, and DF: Same as for immersion. Terminal strength: Method 211 of MIL-STD-202, conditions A and D. Condition A: Applied force 5 pounds.

36、 Condition D: 3 rotations of 360 degrees. Low temperature and capacitance change with temperature: Low temperature: -55C +0C, -3C for 48 hours 4 hours with rated voltage applied. Capacitance change with temperature: At -55C +0C, -3C: -10 percent, maximum. At +125C +4C, -0C: +20 percent maximum. Fung

37、us: Method 508 of MIL-STD-810. Resistance to soldering heat: Method 210 of MIL-STD-202, condition C, except the time shall be 10 seconds 1 second. IR: See table II. Capacitance: Within 5 percent of initial value. DF: Not more than 1.0 percent. Life: Method 108 of MIL-STD-202. Qualification: Accelera

38、ted conditions: 140 percent of rated voltage for 2,000 +72, -0 hours. Rated conditions: 100 percent of rated voltage for 10,000 +96, -0 hours. DF (at +125C +4C, -0C) between 24 and 48 hours of test: 2 percent, maximum. During last 48 hours of test: 2.5 percent, maximum. IR: Insulating sleeves: 100 m

39、egohms, minimum. Terminal to terminal: Not less than 33.3 percent of initial requirement. Terminals to case (when case is not a terminal): 5,000 megohms, minimum. Capacitance: Within 10 percent of initial value. DF (at +25C 3C after life): 1.25 percent.Provided by IHSNot for ResaleNo reproduction or

40、 networking permitted without license from IHS-,-,-MIL-PRF-39022/2G 7 Quality conformance: 240 hours at accelerated conditions and meet the requirements for qualification test. Extended life: Accelerated conditions: 2,000 +72, -0 hours. Rated conditions: 10,000 +96, -0 hours. Substitutability: See t

41、able IV. Marking: In accordance with MIL-PRF-39022. Part or Identifying Number (PIN): M39022/02- (dash number from table I). TABLE IV. Substitutability data. Dash number in Type designation in Dash number in MIL-C-39022/2C thru MIL-PRF-39022/2G 1/ MIL-C-39022/2B MIL-C-39022/2A L (5.0) M (1.0) P (0.1

42、) R (0.01) S (0.001) 2/ and /2 1001 1111 1221 1331 1441 CHR19A1NC104- 0001 1002 1112 1222 1332 1442 CHR19A1NC104- 0002 1003 1113 1223 1333 1443 CHR19A3NC104- 0003 1004 1114 1224 1334 1444 CHR19A3NC104- 0004 1005 1115 1225 1335 1445 CHR19A1NC154- 1006 1116 1226 1336 1446 CHR19A1NC154- 1007 1117 1227

43、1337 1447 CHR19A3NC154- 1008 1118 1228 1338 1448 CHR19A3NC154- 1009 1119 1229 1339 1449 CHR19A1NC224- 0005 1010 1120 1230 1340 1450 CHR19A1NC224- 0006 1011 1121 1231 1341 1451 CHR19A3NC224- 0007 1012 1122 1232 1342 1452 CHR19A3NC224- 0008 1013 1123 1233 1343 1453 CHR19A1NC334- 1014 1124 1234 1344 14

44、54 CHR19A1NC334- 1015 1125 1235 1345 1455 CHR19A3NC334- 1016 1126 1236 1346 1456 CHR19A3NC334- 1017 1127 1237 1347 1457 CHR19A1NC474- 0009 1018 1128 1238 1348 1458 CHR19A1NC474- 0010 1019 1129 1239 1349 1459 CHR19A3NC474- 0011 1020 1130 1240 1350 1460 CHR19A3NC474- 0012 1021 1131 1241 1351 1461 CHR1

45、9A1NC684- 1022 1132 1242 1352 1462 CHR19A1NC684- 1023 1133 1243 1353 1463 CHR19A3NC684- 1024 1134 1244 1354 1464 CHR19A3NC684- 1025 1135 1245 1355 1465 CHR19A1NC105- 0013 1026 1136 1246 1356 1466 CHR19A1NC105- 0014 1027 1137 1247 1357 1467 CHR19A3NC105- 0015 1028 1138 1248 1358 1468 CHR19A3NC105- 00

46、16 1029 1139 1249 1359 1469 CHR19A1NC155- 0017 1030 1140 1250 1360 1470 CHR19A1NC155- 0018 1031 1141 1251 1361 1471 CHR19A3NC155- 0019 1032 1142 1252 1362 1472 CHR19A3NC155- 0020 See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from

47、IHS-,-,-MIL-PRF-39022/2G 8 TABLE IV. Substitutability data - Continued. Dash number in Type designation in Dash number in MIL-C-39022/2C thru MIL-PRF-39022/2G 1/ MIL-C-39022/2B MIL-C-39022/2A L (5.0) M (1.0) P (0.1) R (0.01) S (0.001) 2/ and /2 1033 1143 1253 1363 1473 CHR19A1NC205- 0021 1034 1144 1

48、254 1364 1474 CHR19A1NC205- 0022 1035 1145 1255 1365 1475 CHR19A3NC205- 0023 1036 1146 1256 1366 1476 CHR19A3NC205- 0024 1037 1147 1257 1367 1477 CHR19A1NC305- 0025 1038 1148 1258 1368 1478 CHR19A1NC305- 0026 1039 1149 1259 1369 1479 CHR19A3NC305- 0027 1040 1150 1260 1370 1480 CHR19A3NC305- 0028 1041 1151 1261 1371 1481 CHR19A1NC435- 1042 1152 1262 1372 1482 CHR19A1NC435- 1043 1153 1263 1373 1483 CHR19A3NC435- 1044 1154 1264 1374 1484 CHR19A3NC435- 1045 1155 1265 1375 1485 CHR19A1NC515- 1046 1156 1266 1376 1486 CHR19A1NC515- 1047 1157 1267 1377 1487 CHR19A3NC515- 1048 115