DLA MIL-PRF-39035 3 F-2009 RESISTORS VARIABLE NONWIREWOUND (ADJUSTMENT TYPE LEAD-SCREW ACTUATED) NONESTABLISHED RELIABILITY AND ESTABLISHED RELIABILITY STYLE RJR26.pdf

1、Comments, suggestions, or questions on this document should be addressed to: Defense Supply Center, Columbus, ATTN: DSCC-VAT, Post Office Box 3990, Columbus, Ohio 43218-3990 or by email Resistordla.mil. Since contact information can change, you may want to verify the currency of this address informa

2、tion using the ASSIST Online database at http:/assist.daps.dla.mil/. AMSC N/A FSC 5905 INCH-POUND MIL-PRF-39035/3F 29 July 2009 SUPERSEDING MIL-PRF-39035/3E 6 June 2003 PERFORMANCE SPECIFICATION RESISTORS, VARIABLE, NONWIREWOUND (ADJUSTMENT TYPE, LEAD-SCREW ACTUATED), NONESTABLISHED RELIABILITY, AND

3、 ESTABLISHED RELIABILITY STYLE RJR26 This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-PRF-39035. 1. SCOPE 1.1 Scope. This specification co

4、vers the requirements for style RJR26, nonestablished reliability and established reliability, adjustment type, lead-screw actuated, nonwirewound, variable resistors. This style is available in characteristic F and H. 1.2 Part or Identifying Number (PIN). Resistors covered by this specification must

5、 be identified by a PIN which must consist of a basis style of this specification and a coded number. The PIN must be in the following form and is derived from MIL-PRF-39035. RJR26 FP102M | | | | Specification style number Coded number 2. APPLICABLE DOCUMENTS 2.1 General. The documents listed in thi

6、s section are specified in sections 3 and 4 of this specification. This section does not include documents cited in other sections of this specification or recommended for additional information or as examples. While every effort has been made to ensure the completeness of this list, document users

7、are cautioned that they must meet all specified requirements documents cited in sections 3 and 4 of this specification, whether or not they are listed. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-39035/3F 22.2 Government documents. 2.2.1

8、Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract (see 6.2). DEPARTMENT OF DEFENSE SPE

9、CIFICATION MIL-PRF-39035 - Resistors, Variable, Nonwirewound (Adjustment Type), Nonestablished Reliability, and Established Reliability, General Specification for (Copies of these documents are available online at http:/assist.daps.dla.mil/quicksearch/ or from the Standardization Document Order Desk

10、, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094). 2.3 Order of precedence. Unless otherwise noted herein or in the contract, in the event of a conflict between the text of this document and the references cited herein (except for related specification sheets), the text of this documen

11、t takes precedence unless otherwise noted. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 General. The requirements for acquiring the product described herein shall consist of this document and MIL-PRF-

12、39035. 3.2 Interface and physical dimension requirements. Resistors shall meet the interface and physical dimensions specified on figure 1. 3.3 Power rating. The power rating shall be 1/4 watt for characteristics F and H. 3.4 Terminals. Characteristics F and H are available in A, B, C, P, W, and X t

13、ype terminals. 3.5 Nominal resistance value and maximum rated ac or dc working voltage. Nominal resistance values and maximum rated ac or dc working voltages shall be as specified in table I. 3.6 Actual effective electrical travel. Actual effective electrical travel shall be 10 turns minimum, and 25

14、 turns maximum. 3.7 Operating torque. Operating torque shall be a maximum of 3 ounces-inches. 3.8 Maximum voltage. Maximum rated ac or dc working voltage shall be 200 volts. 3.9 Pure tin. The use of pure tin, as an underplate or final finish, is prohibited both internally and externally. Tin content

15、 of resistor components and solder shall not exceed 97 percent, by mass. Tin shall be alloyed with a minimum of 3 percent lead, by mass (see 6.3). 4. VERIFICATION 4.1 Sampling and inspection. Sampling and inspection shall be in accordance with MIL-PRF-39035, and as specified herein. 4.2 Dielectric w

16、ithstanding voltage. In the dielectric withstanding voltage test, the applied potential shall be 600 volts rms at atmospheric pressure, and 250 volts rms at reduced barometric pressure. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-39035/3F

17、 3TERMINAL TYPE A TERMINAL TYPE B FIGURE 1. Style RJR26 resistors. .075 .025 (LOCATED IN SHADED AREA) .250 .020 .165 .020PIN MARKING ON THIS SURFACE .020.115MAX.017 DIA. .0023 PINS123.270 .020.172MIN.100.100.030 .010.040 +.010 -.015.050MAX.018 1 2 3 .020 .250 .020 .115 MAX. .018 MIN. .075 DIA. .015

18、(LOCATED IN SHADED AREA) .050 MAX. .165 .020 .270 .020.172MIN.PIN MARKINGON THIS SURFACE.100.100.030 .010.100.040 +.010 -.015 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-39035/3F 4TERMINAL TYPE C TERMINAL TYPE P FIGURE 1. Style RJR26 resi

19、stors - Continued. .172MIN.195 .020 .017 DIA. .0023 PINS.018MIN.075 DIA. .015 (LOCATED IN SHADED AREA) .100 .250 .020.050MAX.020.125 .010 .250 .020.030 .010132.100 .100.015MIN.115 MAX. MARKING ONTHIS SURFACE.250 .020.050MAX.018MIN.020132.100.100 .100 .125 .010.250 .020.172 .175 .020 .115 MAX. .075 .

20、015 (LOCATED IN SHADED AREA)DIA. PIN MARKINGON THIS SURFACE.017 .002 3 PINS DIA. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-39035/3F 5TERMINAL TYPE W TERMINAL TYPE X FIGURE 1. Style RJR26 resistors - Continued. .016 DIA. +.001 3 PINS .10

21、0.020 .250 .020 .115 MAX. .018 MIN. .075 DIA. .015 (LOCATED IN SHADED AREA) .050 MAX. .165 .020 .250 .020.172MIN.PIN MARKINGON THIS SURFACE.100.100.030 .010.040 +.010-.015 1 23 .250 .020.172MIN.100.100.030 .010.040 +.010 -.015 .050 MAX. .018 .075 .025 (LOCATED IN SHADED AREA) .250 .020 .165 .020 PIN

22、 MARKING ON THIS SURFACE .020.115MAX.017 DIA. .0023 PINS1 2 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-39035/3F 6SCHEMATIC DIAGRAM Inches mm Inches mm Inches mm Inches mm Inches mm 0.002 0.051 0.018 0.46 0.040 1.02 0.115 2.92 0.175 4.4

23、4 0.010 0.250 0.020 0.51 0.050 1.27 0.125 3.18 0.195 4.95 0.015 0.381 0.025 0.64 0.075 1.90 0.165 4.19 0.250 6.35 0.017 0.432 0.030 0.76 0.100 2.54 0.172 4.37 0.270 6.86 NOTES: 1. Dimensions are in inches. 2. Unless otherwise specified, tolerance is 0.005 (0.13 mm). 3. Metric equivalents are given f

24、or general information only. 4. The entire slot of the actuating screw must be above the surface of the unit. 5. The head of the lead screw actuator shall not extend beyond any edge of the surface upon which it is mounted. 6. Mounting means are by use of pins only. 7. Standoff shape and location is

25、optional. FIGURE 2. Style RJR26 resistors - Continued. TABLE I. Nominal resistance value and maximum rated ac or dc working voltage. Nominal resistance value (in ohms) Maximum rated ac or dc working voltage per characteristics Nominal resistance value (in Ohms) Maximum rated ac or dc working voltage

26、 per characteristics F and H F and H 10 20 50 100 200 500 1,000 2,000 5,000 10,000 1.58 2.23 3.54 5.0 7.07 11.1 15.8 22.3 35.4 50.0 20,000 25,000 50,000 Megohms 0.10 0.20 0.25 0.50 1.00 70.7 79.0 111.0 158 200 200 200 200 Provided by IHSNot for ResaleNo reproduction or networking permitted without l

27、icense from IHS-,-,-MIL-PRF-39035/3F 75. PACKAGING 5.1 Packaging. For acquisition purposes, the packaging requirements shall be as specified in the contract or order (see 6.2). When packaging of materiel is to be performed by DoD or in-house contractor personnel, these personnel need to contact the

28、responsible packaging activity to ascertain packaging requirements. Packaging requirements are maintained by the Inventory Control Points packaging activity within the Military Service or Defense Agency, or within the military services system commands. Packaging data retrieval is available from the

29、managing Military Departments or Defense Agencys automated packaging files, CD-ROM products, or by contacting the responsible packaging activity. 6. NOTES (This section contains information of a general or explanatory nature that may be helpful, but not mandatory.) 6.1 Intended use. The notes specif

30、ied in MIL-PRF-39035 are applicable to this specification. 6.2 Acquisition requirements. Acquisition documents must specify the following: a. Title, number, and date of this specification, and the complete PIN (see 1.2). b. Unless otherwise specified (see 2.1), the versions of the individual documen

31、ts referenced will be those in effect on the date of release of the solicitation. c. Packaging instructions (see 5.1). 6.3 Tin whisker growth. The use of alloys with tin content greater than 97 percent, by mass, may exhibit tin whisker growth problems after manufacture. Tin whiskers may occur anytim

32、e from a day to years after manufacture and can develop under typical operating conditions, on products that use such materials. Conformal coatings applied over top of a whisker-prone surface will not prevent the formation of tin whiskers. Alloys of 3 percent lead, by mass, have shown to inhibit the

33、 growth of tin whiskers. For additional information on this matter, refer to ASTM-B545 (Standard Specification for Electrodeposited Coatings of Tin). 6.4 Changes from previous issue. The margins of this specification are marked with vertical lines to indicate where changes from the previous issue we

34、re made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations and relation

35、ship to the last previous issue. Custodians: Preparing activity: Army - CR DLA - CC Navy - EC Air Force - 85 DLA - CC Review activities: (Project 5905-2009-015) Army - AR, AT, AV, CR4, MI Navy - AS, CG, MC, OS Air Force - 19, 99 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-