DLA MIL-PRF-43473 G-1997 CLOTH WATERPROOF《防水布》.pdf

1、HIL-PRF-43473G 9999906 2059375 837 W I INCH-POUND I MIL-PRF-43473G 02 December 1997 SUPERSEDING MIL-C-43473F 29 March 1988 PERFORMANCE SPECIFICATION CLOTH, WATERPROOF This specification is approved for use by all Departments and Agencies of the Department of Defense. 1. SCOPE 1.1 Scope. This specifi

2、cation covers three types of waterproof cloth. 1.2 Classification. The following types of cloth cited in this specification are as follows (see 6.2). Type I - Camouflage Green 483 Type II - Deleted Type III - Woodland Camouflage Type IV - Desert Camouflage 2. APPLICABLE DOCUMENTS 2.1 General. The do

3、cuments listed in this section are specified in sections 3 and 4 of this specification. This section does not include documents cited in other sections of this specification or recommended for additional information or as examples. While every effort has been made to ensure the completeness of this

4、list, document users are cautioned that they must meet all specified requirements documents cited in sections 3 and 4 of this specification, whether or not they are listed. Beneficial comments (recommendations, additions, deletions, clarifications) and any pertinent data which may be of use in impro

5、ving this document should be addressed to: Defense Personnel Support Center, Clothing and Textiles Directorate, Attn: DPSC-FNS, 2800 South 20th Street, Philadelphia, PA 19145-5099 by using the Standardization Document Improvement Proposal D Form 1426) appearing at the end of this document or bv lett

6、er AMSC N/A FSC 8305 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. Licensed by Information Handling ServicesMIL-PRF-43473G W 999990b 205937b 773 W MIL-PRF-43473G 2.2 Government documents. 2.2.1 Specifications, standards, and handbooks. The following specifications

7、, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those listed in the issue of the Department of Defense Index of Specifications and Standards (DODISS) and supplement thereto, cited in the solicitatio

8、n (see 6.2). STANDARDS FEDERAL FED-STD- 19 1 FED-STD-595 - Textile Test Methods - Colors Used in Government Procurement MILITARY MIL-STD-96 1 MIL-STD- 1487 - Department of Defense Standard Practice For Defense Specifications - Glossary of Cloth Coating Imperfections (Unless otherwise indicated. copi

9、es of federal and military specifications, standards, and handbooks are available from the Standardization Documents Order Desk. 700 Robbins Avenue, Bldg. 4D, Philadelphia, PA 191 1 1-5094.) 2.2.2 Other Government documents, drawings. and publications. The following other Government documents, drawi

10、ngs, and publications form a part of this document to the extent Specified herein. Unless otherwise specified, the issues are those cited in the solicitation. CODE OF FEDERAL REGULATIONS (Applications for copies of referenced documents should be addressed to U. S. Government Printing Office, Superin

11、tendent of Documents, Mail Stop: SSOP, Washington, DC 20402-9328.) FEDERAL, TRADE COMMISSION Rules and Regulations Under-the Textile Fiber Products Identification Act (Copies are available from the Federal Trade Commission, Pennsylvania Avenue at Sixth Street, N.W., Washington, DC 20580-0001.) U. S.

12、 ARMY CENTER FOR HEALTH PROMOTION AND PREVENTATIVE MEDICINE Contact Allergy: Predictive Testing in Humans“, Advances in Modem Toxicology (Applications for copies of referenced documents should be addressed to U. S. Army Center for Health Promotion and Preventative Medicine, ATTN: MCHB-DC-TTE, Bldg.

13、E-2 100, Aberdeen Proving Grounds, MD 2 1 O1 0-5442.) FEDERAL ACQUISITION REGULATIONS (FAR) FAR 52.209 - First Article Testing 2 Licensed by Information Handling Services. MIL-PRF-43473G H 999990b 2059377 bOT = MIL-PRF-43473G 8 (Applications for copies of referenced documents should be addressed to

14、the Superintendent of Documents, P. O. Box 371954, Pittsburgh, PA 15250-7954.) BUREAU OF ALCOHOL,TOBACCO AND FIREARMS, DEPARTMENT OF THE TREASURY Formulas for Denatured Alcohol (27 CFR Part 21) (Applications for copies of referenced documents should be addressed to the Bureau Of Alcohol, Tobacco And

15、 Firearms, Department Of The Treasury, 1200 Pennsylvania Ave. Washington, DC 20226.) ENVIRONMENTAL PROTECTION AGENCY Regulations for the Enforcement of the Federal Insecticide, Fungicide and Rodenticide Act (40 CFR Part 1 62) (Applications for copies of referenced documents should be addressed to th

16、e Environmental Protection Agency, 401 M Street SW, Washington, DC 20460.) DRAWINGS U.S. ARMY NATICK RESEARCH, DEVELOPMENT Water Permeability; Hydrostatic Pressure ASTM-D-1424 - Tear Resistance of Woven Fabrics by Falling Pendulum (Elmendorf) ASTM-D- 1776 - Standard Practice for Conditioning Textile

17、s For Testing ASTM-D-3776 - Mass Per Unit Area (Weight) of Woven Fabric ASTM-D-3886 - Abrasion Resistance of Textile Fabrics (Inflated Diaphragm Method) ASTM-D-5035 - Breaking Force And Elongation of Textile Fabrics (Strip Force) (Applications for copies of referenced documents should be addressed t

18、o the American Society for Testing and Materials, 100 Barr Harbor Drive, West Conshohocken, PA 19426- 2959.) Method Apparatus 3 Licensed by Information Handling Services HIL-PRF-43473G W 9990b 2059178 546 MIL-PRF-43473G Characteristic Weight OdydL (max) Breaking Strength, lbs. (min): warp Filling wa

19、rp Filling Tearing Strength, grams (min): TECHNICAL MANUAL OF THE AMERICAN ASSOCIATION OF TEXTILE CHEMISTS AND COLORISTS (AATCC) Requirements 3.25 50 50 700 900 AATCC-8 AATCC- 1 1 1 AATCC- 169 - Colorfastness to Crocking: AATCC Crockmeter Method - Weather Resistance: Exposure to Natural Light And We

20、ather Through - Weather Resistance of Textiles: Xenon Lamp Exposure Glass (Applications for copies of referenced documents should be addressed to the American Association of Textile Chemists and Colorists, P.O. Box 12215, Research Triangle Park, NC 27709-22 15.) TECHNICAL ASSOCIATION OF THE PULP AND

21、 PAPER INDUSTRY (TAPPI) TAPPI Method T-45 1 , Stiffness, Preferred Procedure (1) (Applications for copies of referenced documents should be addressed to TAPPI Press, Technology ParuAtlanta, P.O. Box 1051 13, Atlanta, GA 30348-51 13.) SEARS ROEBUCK AND COMPANY FABRIC DEFECT SCALES (Fabric defect repl

22、ica kits are available from Sears Roebuck and Company, Department 8 17, (ATTN: BSC 23-29), Sears Tower, Chicago, IL 60684). 2.4 Order of precedence. In the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence. Nothing in th

23、is document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 First article. When specified (see 6.2), a sample shall be subjected to first article inspection (see 6.3), in accordance with 4.2. 3.2 Standard sample. The waterproof

24、cloth shall match the standard sample for shade and appearance and shall be equal to or better than the sample for colorfastness (see 6.4). 3.3 Performance requirements. The types I, III and IV cloth shall conform to the requirements specified in Table I and 3.4 through 3.8. TABLE I. Reauiremens 4 L

25、icensed by Information Handling Services MIL-PRF-43473G m 9999906 2059179 482 m MIL-PRF-43473G TABLE I. Requirements - 1/ The cloth shall not become stiff and brittle nor soft and tacky and there shall be no evidence of cracking or crazing under visual examination. - 21 “Appreciable change in color“

26、 means a change that is immediately noticeable on comparison of the test specimen with the original, unexposed sample. If closer inspection or a change of angle of light is required to make apparent a slight change of color, the change is not considered appreciable. area. greater than scale rating (

27、2) (slight blocking) (see 6.5.1). - 31 Leakage is defined as the appearance of water anywhere within the 4 1/2 inch diameter test 0 The cloth shall show no lifting, no tackiness, no solution, no pickoff, no adherence to itself - 5/ Equal to or better than the standard sample. - 6/ Applicable only if

28、 a film or coating is used. 3.4 Color. (types defined in accordance with FED-STD-595). 3.4.1 Type I. The color of the cloth shall be Camouflage Green 483 matching color chip 34094 of FED-STD-595 (see 3.2 and 6.4). 3.4.2 Type IIi. The color of the cloth shall be Light Green 354, Dark Green 355, Dark

29、Brown 356 and Black 357 with each area matching the specific colors of the Woodland Camouflage pattern on the standard sample (see 3.2 and 6.4). 3.4.3 Type IV. The color of the cloth shall match shades Light Tan 492, Light Brown 493 and Light Khaki 494. Each area shall match the specific colors of t

30、he pattern or the standard sample (see 3.2 and 6.4). Licensed by Information Handling ServicesLight Tan 492 Min Max Light Brown 493 Light Khaki 494 Min Max Min Max MIL-PRF-43473G m 9999906 2059380 3T4 m MIL-PRF-43473G 3.4.3.1 Colorfastness to crocking; (all types). All colors (both sides) except Bla

31、ck 357 shall show an AATCC Chromatic Transference Scale rating for crocking not less than 3.5. Black 357 shall show an AATCC Chromatic Transference Scale rating for crocking not less than 1.5 when tested as specified in 4.3.2. 3.5 Spectral reflectance. The spectral reflectance requirements of the Ty

32、pe I Camouflage Green 483 cloth and for Type III, Woodland Camouflage cloth shall conform to the requirements specified in Table IIa. The spectral reflectance requirements of the Type IV Desert Camouflage cloth shall conform to the requirements specified in Table IIb. TABLE IIa. Spectral reflectance

33、 requirements: Reflectance (%) Type I camouflage Green 483 Type III Dark Green 355 adjust to achieve required relative humidity (see e. above). g. The test specimens shall fit smoothly on the specimen rack of the apparatus with no wrinkles or gaps. The test specimen shall be mounted to the outside o

34、f the rack with the use of appropriate stainless steel spring clips. After the required exposure period, the specimens shall be removed from the apparatus and allowed to dry and condition at Standard Conditions. 11 Licensed by Information Handling ServicesMIL-PRF-434736 0b 2059386 bL2 D MIL-PW-43473

35、G NOTE: Monitoring of dry bulb temperature, wet bulb depression, irradiance, and black panel temperature is recommended through the use of chart recorders. 4.4.9 Adhesion of coating. ASTM-D-75 1, Adhesion of Coating with 2 inch wide reinforced coating adhesion specimens, cyanoacrylate (solventless)

36、adhesive, and pulling clamp speed of 5 mm/s. Three test specimens shall be tested for each test surface, as appropriate. Test specimens shall be prepared by adhering only coating or film surfaces of test strips together in such a manner that like surfaces are adhered (i.e., face-to face or back-to-b

37、ack). 4.4.10 Blocking. ASTM D-751, Determination of Blocking Resistance of Fabrics Face with Rubber or Plastics at Elevated Temperatures, except that only one specimen shall be exposed at an oven temperature of 180F k2“F for 30 minutes. 4.4.1 1 Color matching. The color of the waterproof cloth shall

38、 match the standard sample when viewed under filtered tungsten lamps that approximate artificial daylight and that have a correlated color temperature of 7500 shall be a good match to the standard sample under incandescent lamplight at 2300 i 2000K. 2000K, with illumination of 100 20 foot candles, a

39、nd 4.4.12 Spectral reflectance tests. Spectral reflectance data shall be determined on the face side and shall be obtained from 600 to 860 nm respectively, at 20 nm intervals on a spectrophotometer relative to a barium sulfate standard, the preferred white standard. Other white reference materials m

40、ay be used, provided they are calibrated to absolute white; e+, magnesium oxide, or vitrolite tiles. The spectral band width at 860 nm shall be less than 26 nm. Reflectance measurements shall be made by either the monochromatic or polychromatic mode of operation. When the polychromatic mode is used,

41、 the spectrophotometer shall operate with the specimen diffusely illuminated with the full emission of a continuous source that simulates either CIE Source A or CIE Source D65. The specimen shall be measured as a single layer backed with two layers of the same fabric and shade. Measurements shall be

42、 taken on a minimum of two different areas, and the data averaged. The measurement areas should be at least 6 inches away from the edges of the finished cloth. The specimen shall be viewed at an angle no greater than 10“ from normal, with the specular component included. Photometric accuracy of the

43、spectrophotometer shall be within 1 percent and wavelength accuracy within 2 nm. The standard aperture size used in the color measurement device shall be 1 .O to 1.25 inches in diameter. Any color having spectral reflectance values falling outside the limits at four or more of the wavelengths specif

44、ied in 3.5 shall be considered a test failure. 4.4.13 Pattern execution. The pattern on the cloth shall be matched to the pattern drawing (see 6.4). 4.4.14 Toxicity assessment. The cloth shall be tested for toxicity as follows: a) Title 40, Code of Federal Regulations, 1994 Edition; Section 798.4100

45、- Dermal Sensitization Section 798.4470- Primary Dermal Irritation Section 798.4500- Primary Eye Irritation Marzulli, F. . Camouflage Parka Trousers Wet Weather clothing system Woodland Custodians: Navy - NU Air Force - 99 Army - GL Preparing activity DLA-CT Project Number 8305-0633 Review activities: Navy - MC Air Force 45,82 14 Licensed by Information Handling Services