DLA MIL-PRF-6106 41 C-2012 RELAY ELECTROMAGNETIC 25 AMPERES 3PNO WITH 2 AMPERE 1PDT AUXILIARY CONTACTS HERMETICALLY SEALED TYPE I.pdf

1、 AMSC FSC 5945 MIL-PRF-6106/41C 22 March 2012 SUPERSEDING MIL-PRF-6106/41B 10 November 2000 PERFORMANCE SPECIFICATION SHEET RELAY, ELECTROMAGNETIC, 25 AMPERES, 3PNO, WITH 2 AMPERE 1PDT AUXILIARY CONTACTS, HERMETICALLY SEALED, TYPE I This specification is approved for use by all Departments and Agenc

2、ies of the Department of Defense. The requirements for acquiring the relays described herein shall consist of this specification and the latest issue of MIL-PRF-6106. FIGURE 1. Dimensions and configurations. INCH-POUND Inactive for new design after 15 November 2002. No superseding Provided by IHSNot

3、 for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-6106/41C 2 Inches mm Inches mm .001 0.03 .25 6.4 .002 0.05 .375 9.53.005 0.13 .38 9.7 .03 0.8 .593 15.06.032 0.81 1.187 30.15 .040 1.02 1.406 35.71.080 2.03 1.531 38.89 .152 3.86 1.680 42.67NOTES: 1. Dimensions a

4、re in inches. 2. Metric equivalents are given for general information only. 3. Unless otherwise specified, tolerance is .010 (0.25 mm). 4. Terminal numbers need not appear on the relay header provided there is affixed to the relay a suitable legible circuit diagram that identifies each terminal loca

5、tion specified. 5. The use of diodes on ac relays is optional. Actual application must be shown on label. FIGURE 1. Relay, outline drawing - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-6106/41C 3 REQUIREMENTS: Coil data: Coil d

6、ata: See table I. Duty rating: Continuous. Operational data: Rated contact load: See table II. Operate time: See table I. Release time: See table I. Maximum induced transient voltage (when specified): 42 V. Physical: Dimensions and configurations: See figure 1. Weight (maximum): 0.44 pound (200 gram

7、s). Terminal type: See figure 1 and table I. Strength of terminals and mounting studs: Applicable. Terminal solderability: Finish: Flat black. ENVIRONMENTAL CHARACTERISTICS: Temperature rating: -70C to +125C. Maximum altitude rating: 80,000 feet. Shock, g-level: 50 g. Duration: 11 ms. Maximum durati

8、on contact opening: 2 ms. Vibration - sinusoidal: Operating: G-level: 10 g. Frequency range: 5 to 1,500 Hz. Nonoperating: G-level: 15 g. Frequency range: 20 to 2,000 Hz. Acceleration: 10 g.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-TABLE I. Moun

9、ting, termination, and operating characteristics. Dash no. Coil term-inal X1, X2 Coil data Time (milliseconds-maximum) Terminals MountingNominal Maximum Max pickup voltage 1/ Hold volt-age 2/ Drop out volt-age 2/ Oper-ate 3/ Re-lease4/ Contact bounce Volts 1/ Freq Res 10% Volts Amp Nominal 2/ High t

10、emp test Cont current test Main Aux NO NC NO NC -001 DC 28 DC - 29 0.25 18 19.5 22.5 7.0 1.5 20 10 2.0 - 4.0 4.0 Solder hook 4 Studs -002 AC 115 400 - 122 .055 96 100 108 40 5.0 25 50 2.0 - 4.0 4.0 Solder hook 4 Studs -003 AC 115 50/60 - 122 .06 96 100 108 40 5.0 25 50 2.0 - 4.0 4.0 Solder hook 4 St

11、uds -004 DC 5/ 28 DC 160 29 0.25 18 19.5 22.5 7.0 1.5 20 10 2.0 - 4.0 4.0 Solder hook 4 Studs 1/ CAUTION: Use of any coil voltage less than nominal coil voltage will compromise the operation of the relay. 2/ Over the temperature range. 3/ With nominal coil voltage. 4/ From nominal coil voltage. 5/ S

12、uppressed dc coil: Back EMF 42 volts maximum. TABLE II. Rated contact load (amperes per pole) case grounded. Type of load Life operating cycles x 10328 V dc 115 V ac, 1 phase 115/200 V ac, 3 phase 1/ See approp-riate footnote Main Aux Main Aux Main Aux NO NC NO NC 400 Hz 50/60 Hz 400 Hz 60 Hz 400 Hz

13、 50/60 Hz 400 Hz 60 HZ Resistive 50 25 - 2 2 25 25 2 - 25 25 - - - Inductive 10 15 - 1 1 25 25 1 1 25 25 - - 2/ Motor 50 20 - - - 20 12 - - 20 12 - - - Lamp 50 10 - .5 .5 10 10 .5 - 10 10 - - -Transfer load - - - - - - - - - - - - 3/ Mechanical life reduced current 100 6.3 - .5 .5 6.3 6.3 .5 - 6.3 6

14、.3 - - - Mixed loads Applicable per specification 1/ Absence of value indicates relay is not rated for 3 phase applications. 2/ .7 pF, inductive. 3/ Transfer load indicates relay suitable for transfer between unsynchronized ac power supplies at rating indicated. 4 MIL-PRF-6106/41CProvided by IHSNot

15、for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-6106/41C 5 ELECTRICAL CHARACTERISTICS: Insulation resistance: Initial: 100 megohms. After life or environmental tests: 50 megohms. Dielectric withstanding voltage (sea level): Initial After life tests Coil to case

16、 1,250 V rms 1,000 V rms Auxiliary contacts 1,000 V rms 750 V rms All other points 1,500 V rms 1,125 V rms Dielectric withstanding voltage (altitude): Maximum contact drop: Initial: 0.150 volt. After life test: 0.175 volt. Overload current: 80 amperes dc, 120 amperes ac. Rupture current: 100 amperes

17、 dc, 150 amperes ac. RFI specification (applicable to coil currents of ac operated relays): MIL-STD-461. PART NUMBER: M6106/41 (plus dash number from table I). Qualification by similarity: See MIL-PRF-6106. Changes from previous issue. The margins of this specification are marked with vertical lines

18、 to indicate where changes from the previous issue were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire conten

19、t irrespective of the marginal notations and relationship to the last previous issue. 80,000 feetCoil to case 500 V rms Auxiliary contacts 250 V rms All other points 500 V rms Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-6106/41C 6 Referen

20、ced documents. In addition to MIL-PRF-6106, this document references the following: MIL-STD-461 Custodian: Preparing activity: Air Force - 85 DLA-CC DLA-CC Review activities: (Project 5945-2012-005) Air Force 99 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.daps.dla.mil/. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-