ImageVerifierCode 换一换
格式:PDF , 页数:6 ,大小:83.36KB ,
资源ID:693092      下载积分:10000 积分
快捷下载
登录下载
邮箱/手机:
温馨提示:
如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
如填写123,账号就是123,密码也是123。
特别说明:
请自助下载,系统不会自动发送文件的哦; 如果您已付费,想二次下载,请登录后访问:我的下载记录
支付方式: 支付宝扫码支付 微信扫码支付   
注意:如需开发票,请勿充值!
验证码:   换一换

加入VIP,免费下载
 

温馨提示:由于个人手机设置不同,如果发现不能下载,请复制以下地址【http://www.mydoc123.com/d-693092.html】到电脑端继续下载(重复下载不扣费)。

已注册用户请登录:
账号:
密码:
验证码:   换一换
  忘记密码?
三方登录: 微信登录  

下载须知

1: 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。
2: 试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。
3: 文件的所有权益归上传用户所有。
4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
5. 本站仅提供交流平台,并不能对任何下载内容负责。
6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。

版权提示 | 免责声明

本文(DLA MIL-PRF-83726 30 J-2013 RELAY HYBRID TIME DELAY (ON OPERATE) CLASS B TYPE I HERMETICALLY SEALED DPDT 10 AMPERES ADJUSTABLE TIME DELAY (EXTERNAL RESISTOR) 0 1 TO 500 SECONDS.pdf)为本站会员(王申宇)主动上传,麦多课文库仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文库(发送邮件至master@mydoc123.com或直接QQ联系客服),我们立即给予删除!

DLA MIL-PRF-83726 30 J-2013 RELAY HYBRID TIME DELAY (ON OPERATE) CLASS B TYPE I HERMETICALLY SEALED DPDT 10 AMPERES ADJUSTABLE TIME DELAY (EXTERNAL RESISTOR) 0 1 TO 500 SECONDS.pdf

1、AMSC N/A FSC 5945 INCH-POUND MIL-PRF-83726/30J 26 February 2013 SUPERSEDING MIL-PRF-83726/30H 18 June 2012 PERFORMANCE SPECIFICATION SHEET RELAY, HYBRID, TIME DELAY (ON OPERATE), CLASS B, TYPE I, HERMETICALLY SEALED, DPDT, 10 AMPERES, ADJUSTABLE TIME DELAY (EXTERNAL RESISTOR), 0.1 TO 500 SECONDS Thi

2、s specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the relay described herein shall consist of this specification and MIL-PRF-83726. FIGURE 1. Outline dimensions and configuration of relay. Provided by IHSNot for ResaleNo

3、reproduction or networking permitted without license from IHS-,-,-MIL-PRF-83726/30J 2 FIGURE 1. Outline dimensions and configuration of relay Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-83726/30J 3 Inches mm Inches mm .001 0.03

4、 .300 7.62 .002 0.05 .312 7.92 .005 0.13 .625 15.88 .040 1.02 .930 23.60 .050 1.27 1.010 25.65 .062 1.57 1.025 26.04 .150 3.81 1.396 35.46 .156 3.96 1.446 33.73 .200 5.08 1.718 43.64 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only. 3. Unless otherwise

5、 specified, tolerance is .010 (0.25 mm) for three place decimals and .03 (0.76 mm) for two place decimals. 4. Terminal numbers shall not appear on the relay header and there shall be a legible circuit diagram on relay which identifies each terminal location specified. 5. Gasket material: The gasket

6、material shall be of such quality to ensure the relay meets all the performance requirements of this specification. Silicone rubber gasket SAE-AMS-3332, shore hardness 20 5 has been considered acceptable. 6. Terminal composition: The terminal composition shall be of such quality to ensure the relay

7、meets all the performance requirements of this specification. Gold in accordance with SAE-AMS-2422 or ASTM-B488, Type 3; underplating: nickel, 50 microinches to 150 microinches thick; has been considered acceptable. 7. External resistor: In accordance with MIL-PRF-55182 (RNC60HXXXXFS), is selected a

8、s follows: REXT = (T1/T0) 1)100k T0 = Minimum time T1 = Required time T1 10 T0 8. Terminal C2 is optional. FIGURE 1. Outline dimensions and configuration of relay Continued. REQUIREMENTS: OPERATING REQUIREMENTS: Timing action: Delay-on-operate. Time delay: Adjustable; select from 0.1 second to 500 s

9、econds. Timing accuracy: 10 percent of nominal value. (The accuracy requirement applies for any combination of operating temperature and voltage. External resistors shall be in accordance with MIL-R-10509, characteristic C or equivalent. Add 10 ms for timing less than 1 second.) Recycle time: 50 mil

10、liseconds maximum. (Recycle time is defined as the minimum time that power must be removed from the input terminals to assure that the next timing cycle will be completed within the specified timing tolerance. (Units can be recycled during timing or after time-out.) Provided by IHSNot for ResaleNo r

11、eproduction or networking permitted without license from IHS-,-,-MIL-PRF-83726/30J 4 Power interrupt: 500 microseconds. (Transient and power loss specifications are based on a maximum duty cycle of 1/50.) Operating current: 150 mA maximum at 25C. INPUT REQUIREMENTS: Input voltage range: 20 V dc to 3

12、0 V dc. (Minimum high temperature test 21 V dc, minimum continuous current test 23.5 V dc.) Duty rating: Continuous. Polarity protection: The timer shall be inoperative during, and undamaged by, reversal of the polarity of the operating voltage. OUTPUT REQUIREMENTS: (At +25C unless otherwise specifi

13、ed.) Configuration: DPDT. Life: See table I. TABLE I. Life load ratings (relay case grounded). Type of load Life (cycles) Amperes 28 V dc Amperes 115/200 V ac 400 Hz Resistive Inductive Motor Lamp Low level 1/ 100,000 20,000 100,000 100,000 100,000 10 8 4 2 10 8 4 2 - 1/ Contact load 10 A to 50 A at

14、 10 mV to 50 mV (dc or peak ac). ELECTRICAL REQUIREMENTS: Transients: In accordance with MIL-STD-704 for 28 volts dc system (figure 11). Spike: Self-generated: 50 volts maximum. Spike transients: 600V, 10 microseconds maximum. Susceptibility: + 80V maximum; -600 V maximum. Electromagnetic interferen

15、ce: In accordance with MIL-STD-461(methods CS101, CS114, RS101, and RS103) for PINs with suffix letter W. (EMI test limits will not be exceeded during the timing interval or when continuously energized under steady-state conditions in accordance with the EMI test of MIL-PRF-83726.) Insulation resist

16、ance: 1,000 megohms at 500 V dc at sea level, and 100 V dc at 80,000 feet between each pin and case. (Terminals X1, X2 and D1, D3 must be connected together during this test. Insulation resistance is measured between all mutually insulated terminals and between all terminals and case.) Provided by I

17、HSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-83726/30J 5 Dielectric withstanding voltage: 1,000 V rms at 60 Hz at sea level, and 350 V rms at 80,000 feet between case and pins connected together. (Terminals X1, X2 and D1, D3 must be connected together

18、during this test. Dielectric withstanding voltage is measured between all mutually insulated terminals and between all terminals and case.) ENVIRONMENTAL REQUIREMENTS: Ambient temperature (operating or non-operating): -55C to +125C. Vibration (sinusoidal): 30 gs, 10 Hz to 3,000 Hz. Moisture resistan

19、ce: Not applicable. Vibration (random): 0.4 g2/Hz power spectral density, 50 Hz to 2,000 Hz in accordance with MIL-STD-202, method 214, test condition 1G. Duration of 15 minutes each plane. Shock (specified pulse): 100 gs, 6 ms 1 ms, sine, 3 axes. Acceleration: 15 gs in any axis. Seal: Hermetic. Max

20、imum altitude rating: 80,000 feet. PHYSICAL REQUIREMENTS: Dimensions and configuration: See figure 1. Mating socket: MIL-DTL-12883/40-01, MIL-DTL-12883/40-05, MIL-DTL-12883/40-07, MIL-DTL-12883/40-11, MIL-DTL-12883/40-13, MIL-DTL-12883/40-17, MIL-DTL-12883/40-19, or MIL-DTL-12883/40-23 in accordance

21、 with MIL-DTL-12883/40. (CAUTION: Consideration should be given to ambient temperature and current requirements when using wire barrels size 20.) Terminations: See figure 1. Terminal strength: 3 pounds pull. Weight: 2.5 ounces maximum. Marking: See MIL-PRF-83726. In addition, relays shall be marked

22、with the ESDS identifier as specified in MIL-STD-1285. Part or Identifying Number (PIN): Consists of the prefix M83726/30-, a four digit dash number (time delay expressed in milliseconds), and a suffix letter (P for plug-in; S for solder lug) as follows:) M 83726/30- 1001 P Military designation Spec

23、ification sheet number The first three digits are significant; the fourth is the number of zeros to follow the first three digits. The time is expressed in milliseconds and converted to seconds. (See examples.) Suffix letter. (Any relay numbered prior to the date of this specification shall be consi

24、dered interchangeable with same mounting type, store and issue.) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-83726/30J 6 Examples: M83726/30-1001P 0.1 to 1 second time delay, plug-in. M83726/30-9002S 9 to 90 second time delay, solder lug.

25、 NOTE: Time delay relays within the 0.1 second to 500 second delay range are available within a one-decade range. The PIN represents the upper timing limit of each range. Marginal notations are marked with vertical lines to indicate where changes from the previous issue were made. This was done as a

26、 convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations and relationship to the last previous i

27、ssue. Referenced documents: In addition to MIL-PRF-83726, this document references the following: MIL-R-10509 MIL-DTL-12883/40 MIL-PRF-55182 MIL-STD-202 MIL-STD-461 MIL-STD-704 MIL-STD-1285 ASTM-B488 SAE-AMS-2422 SAE-AMS-3332 Custodians: Preparing activity: Navy - EC DLA - CC Air Force - 85 DLA CC (

28、Project 5945-2013-008) Review activities: Navy - OS Air Force 19 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-

copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
备案/许可证编号:苏ICP备17064731号-1