DLA MIL-R-83516 4 C-2011 RELAYS REED DRY DUAL IN-LINE PACKAGE (DIP) GENERAL PURPOSE LOW-POWER COIL.pdf

1、AMSC N/A FSC 5945 INCH-POUND MIL-R-83516/4C 1 November 2011 SUPERSEDING MIL-R-83516/4B 30 September 1990 MILITARY SPECIFICATION SHEET RELAYS, REED, DRY, DUAL IN-LINE PACKAGE (DIP), GENERAL PURPOSE, LOW-POWER COIL Inactive for new design after 19 July 2001, and no longer used except for replacement p

2、urposes. This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the relays described herein shall consist of this specification sheet and MIL-DTL-83516. FIGURE 1. Outline drawing. Provided by IHSNot for ResaleNo reproductio

3、n or networking permitted without license from IHS-,-,-MIL-R-83516/4C 2 Inches mm Inches mm .002 .005 .010 .020 .100 0.05 0.13 0.25 0.51 2.54 .150 .290 .300 .600 .770 3.81 7.36 7.62 15.24 19.55 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only. 3. Relay

4、s are available with electrostatic shielding at pin 9. 4. A position identifier (shape optional) shall be placed on the top of each relay centered between pins 1 and 14 or directly over pin 1. 5. Relay heights can be found in table I. 6. Unless otherwise specified, tolerance is .010 (0.25 mm). FIGUR

5、E 1. Outline drawing - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-R-83516/4C 3 FIGURE 1. Outline drawing - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-R-83516/4C

6、 4 TABLE I. Dash numbers and applicable characteristics. Dash number Circuit diagram (See figure 1) Config- uration (See figure 1) DC coil data at 25C Without shielding With shielding Resistance (minimum) ohms Pickup voltage (maximum) Dropout voltage (minimum) Power dissipation (nominal) mW 5-volt c

7、oil 5-volt-coil 001 002 A A 450 4.0 1.0 50 003 004 B A “ “ “ “ 005 006 A B “ “ “ “ 007 008 B B “ “ “ “ 009 010 C A 324 “ “ 170 011 012 D A “ “ “ “ 013 014 C B “ “ “ “ 015 016 D B “ “ “ “ REQUIREMENTS: Design and construction: Dimensions and configurations: See figure 1. Diode characteristics (when a

8、pplicable): Diodes shall be JANTX as a minimum. 1/ Peak inverse voltage: 75.0 V dc. Contact data: Arrangements: See figure 1. Load ratings: Contacts V dc (max) mA (max) VA (max) Form A Form C 100 28 500 250 10 3 _ 1/ WARNING: Reverse polarity on coil terminals will destroy diode. Provided by IHSNot

9、for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-R-83516/4C 5 Contact resistance: Before life: 0.130 ohm maximum. During and after life: 1.0 ohm maximum. Group A inspection: 0.200 ohm maximum. Contact noise: Applicable. Contact stability: Applicable. Coil data: See

10、table I. Duty rating: Continuous. Coil power dissipation: See table I. Operate time: See table II. Release time: See table II. TABLE II. Operate and release time (including bounce). Contact arrangement Operate time (nominal) Release time (nominal) Without diode With diode Without diode With diode Fo

11、rm A ms 1 ms 1 ms .5 ms 1 Form C 2 2 2.5 2.5 Electrical data: Dielectric withstanding voltage: MIL-STD-202, method 301. 2/ Test points: Between all mutually insulated components: 500 V dc. Across contacts: 250 V dc. _ 2/ For relays supplied with an internal diode, the coil leads shall be connected t

12、ogether to avoid damage to the coil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-R-83516/4C 6 Insulation resistance: 10,000 M minimum. Test potential: 100 V dc 10 percent. Test points: Between contacts. Coil transient suppression (relays with

13、 internal diodes): 1.0 V maximum negative transient. Capacitance, pF maximum: 1A 1C Across open contacts, no shield: Across open contacts, shield guarded: Contact to coil, no shield: Contact to coil, shield guarded: 1.25 0.25 3.0 2.0 2.0 1.2 3.5 2.0 Environmental data: Thermal EMF: Not applicable. T

14、hermal shock: Applicable. Shock (specified pulse): Applicable. Vibration, high frequency: Applicable. Salt spray (corrosion): Applicable. Moisture resistance: Applicable. Magnetic interference: Relays are subject to interaction with stray magnetic fields. To keep within operating parameters, relays

15、should be mounted no closer than .500 inch (12.7 mm) of each other. Greater spacing is required for stronger magnetic fields. Resistance to soldering heat: Applicable. Physical: Enclosure: Molded plastic. Operating temperature range: -40C to +85C. Lead integrity: MIL-STD-883, method 2004, test condi

16、tion B2; the force to be applied shall be 8.0 0.5 ounces. Solderability: Applicable. Life: Applicable. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-R-83516/4C 7 Weight: 2.5 grams maximum. Part or Identifying Number (PIN): M83516/4- (dash numbe

17、r from table I). Qualification: Qualification inspection and sample size: See table III. TABLE III. Qualification inspection and sample size. M83516/4- Number of samples 008 016 13 units each part number plus 1 open unit. Qualification inspection as applicable. Quality assurance provisions: Group B

18、inspection not required. Group A inspection required. The qualifying activity shall be notified of any design and/or construction changes and shall impose additional testing requirements as necessary. MIL-DTL-83516A, paragraph 4.5.1.2.2.1, first sentence does not apply. Referenced documents: MIL-DTL

19、-83516 MIL-STD-202 MIL-STD-883 The margins of this specification are marked with vertical lines to indicate where modifications from this revision were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and co

20、ntractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations. Custodian: Preparing activity: Air Force - 85 DLA - CC DLA - CC (Project 5945-2011-016) Review activities: Air Force - 99 NOTE: The activities listed above were i

21、nterested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.daps.dla.mil/ . Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-