DLA MIL-S-29461-1992 SUIT CHEMICAL AND BIOLOGICAL PROTECTIVE (CARBON SPHERE)《化学和生物(碳球)套装》.pdf

1、1 MIL-S-27461 84 7777906 0533787 4 I INCH POUND I MIL-S-29461 07 April 1992 MILITARY SPECIFICATION SUIT, CHEMICAL AND BIOLOGICAL PROTECTIVE (CARBON SPHERE) This specification is approved for use by US Marine Corps, Department of the Navy, and is available for use by all Departments agencies of the D

2、epartment of Defense. 1. SCOPE 1.1 Scope. This specification covers the requirements for a chemical and biological protective suit (coat and trouser). 1.2 Classification. The chemical and biological protective suit shall be of two-piece design, to include a coat, with built-in hood, and trousers. Cl

3、ass 1. - Woodland Camouflage Printed Class 2. - Desert Camouflage Printed Schedule of Sizes The chemical and biological protective suit shall be furnished in the following sizes, and as specified in Section 6.2: SmalJ. Medium Large X-Large Beneficial comments (recommendations, additions, deletions)

4、and any pertinent data which may be of use in improving this document should be addressed to: Defense Personnel Support Center, Clothing and Textiles Directorate, Attn: DPSC-FSSD, 2800 South 20th Street, Philadelphia, PA 19101-8419, by using the self-addressed Standardization Document Improvement Pr

5、oposal (DD Form 1426) appearing at the end of this document or by letter. AMSC N/A FSC 8415 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-S-274bL 84 W 99977Ob 053

6、3988 b MIL-S-29461 2. APPLICABLE DOCUMENTS 2.1 Government Documents. 2.1.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. specified, the issues of these documents shall be those listed in t

7、he issue of the Department of Defense Index of Specifications and Standards (DODISS) and supplement thereto, cited in the solicitation (see 6.2). Unless otherwise SPECIFICATIONS FEDERAL V-F-106 TT-I- 17 9 5 DDD-L-20 PPP-B-636 MILITARY MIL-B-117 MIL-F-21840 MIL-(2-43303 MIL-T-43548 MIL-T-43566 MIL-C-

8、29462 MIL-C-43468 STANDARDS FEDERAL FED-STD-101 FED-CTD-595 FED-STb-751 MILITARY MIL-STD-105 MIL-STD-129 MIL-STD-147 MIL-STD-1668 F steners, Slide Interlocking Ink, Marking, Stencil, Opaque (porous and non porous Surfaces) Label : for Clothing, Equipage, and Tentage (General Use). Box, Shipping, Fib

9、erboard Bags, Sleeves and Tubing-Interior Packaging Fastener Tapes, Hook and Pile, Synthetic Cord, Elastic, Cotton Thread, Polyester, Cotton-covered and Rayon Covered Tape, Textile, Cotton, General Purpose, Natural or in Colors Cloth, Laminated, Polyester Tricot Knit, Activated Carbon Sphere, Chemic

10、al Protective Cloth, Camouflage Pattern: Resistant Poplin, Cotton. Wind Test Procedures for Packaging Materials Colors Stitches, Seams and Stitchings Sampling Procedures and Tables for Inspection by Attributes Marking for Shipment and Storage Palletized Unit Loads Provisions for Evaluating Quality o

11、f Cloth Coveralls i b h 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-S-29461 84 9979906 0533789 8 MIL-S-29461 (Unless otherwise indicated, copies of federal and military specifications and standards are available from the Standardization Doc

12、uments Order Desk, Building 4D, 700 Robbins Avenue, Philadelphia, PA 19111-5094) 2.1.2 Other Government documents, drawinqs, and publications. The following other Government documents form a part of this specification to the extent specified herein. Unless otherwise specified, the issues are those c

13、ited in the solicitation. DRAWINGS 5-10-47 - Fastener, 1 inch 1-6-102 - Slide, 1 inch (Application for copies maybe be requested from the Commander, Natick Research Development and Engineering Center, Kansas Street, Natick, MA. 01760). TEST METHODS CRDC-SP-84010 Laboratory Methods for Evaluating Pro

14、tective Clothing Systems Against Chemical Agents. (Application for copies maybe be requested from the Commander, Chemical Research and Development Center, ATTN: DRSMC-CLJ-IR (A), Aberdeen Proving Ground, Maryland 21010.) 2.2 Non-Government Publications. The following documents form a part of this do

15、cument to the extent specified herein. Unless otherwise specified, the issues of the documents which are DoD adopted shall be those listed in the issue of the DODISS cited in the solicitation. Unless otherwise specified, the issues of documents not listed in the DODISS are the issues of the document

16、s cited in the solicitation. ANNUAL BOOK OF ASlM STANDARDS ASTM D. 3951 Practice for Commercial Packaging (Applications for copies of the ASTM Annual Book of ASTM Standards should be addressed to: ASTM, 1916 Race Street, Philadelphia, PA 19103-1187.) 2.3 Order of precedence. In the event of a confli

17、ct between the text of this document and the references cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3 Provided by IHSNot for ResaleNo reproduction or networking

18、permitted without license from IHS-,-,-99979Db 0533990 4 MIL-S-29461 e 3. REQUIREXENTS 3.1 Standard sample. The Chemical and Biological Protective Suit shall be equal to or better than the standard sample with respect to all chaiacteristics for which the standard sample is referenced (see 6.3). 3.2

19、First article. Unless otherwise specified (see 6.2), before production is commenced, finished suits shall be submitted, or made available to the contracting officer or his authorized representative for approval. authorizes the commencement of production but does not relieve the contractor of respons

20、ibility for compliance with all applicable provisions of the specification. The first article shall be manufactured by the contractor in the same facilities to be used for the manufacture of the production items, The approval of the first article 3.3 Material. 4 3.3.1 Outer shell, The camouflage pri

21、nted and quarpel treated cotton cloth used for the outer shell shall conform to the requirements specified in MIL-C-43468 and Section 6.2. 3.3.2 Lininq. The laminated cloth used for the lining shall conform to MIL-C-29462. 3.3.3 Elastic cord. The cotton elastic cord for the drawcord at bottomof coat

22、 and for the hood drawcord shall be 3/16 inch in diameter, conforming to class 2 of MIL-C-43303. The color shall be camouflage green #483 for Class I and tan #380 for Class II, and the colorfastness requirements shall not apply. 3.3.3.1 Elastic cokd resin impreqnatinq aqent. The resin agent used for

23、 dipping or impregnating the ends of the drawcords shall be cellulose acetate or cellulose acetate butyrate to prevent ravelling. The dipped or impregnated-end shall be at least 1/2 inch in length. 3.3.4 Slide fasteners. The side fasteners shall be continuous element nylon or polyester (spiral type)

24、, size,MS, type IV, style 8, and conforming to the requirements of V-F-106, except that the salt spray test shall not apply. shall be a staple type and shall be positioned and sewn, enclosing the sides and ends of the fastener. chain. Solid type closed-end bottom stops shall abut the end of the slid

25、e fastener tape without damage to the tape or chain. pulls shall be 1“ and shall have a hole with sufficient size to accommodate a 3/8 inch wide thong. The closed-end bottom stop The slide fastener 3.3.4.1 Slide fastener tape. The color of the slide fastener tape shall be #ODs66519 for Class I and #

26、CA6651.6 for ClasS.II., and the colorfastness requirements shall not appzy. 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-S-29463 84 777Ob O533973 b MIL-S-29461 3.3.5 Hook and pile fastener tape. The hook and pile tapes for the trouser shall

27、be 1“ wide for the waist adjustment and for the leg adjustment it shall be 1“ pile and 1 1/2“ wide hook. The hook and pile fastener tapes for securing coat and trouser pockets and flaps, and coat center front overlap shall be 5/8 inch wide hook and pile tape with the exception of coat pocket which s

28、hould be 1“ pile, and for sleeve cuff adjustments shall be 1“ inch wide hook and pile tape conforming to type II, class 1 of MIL-F-21840. The color shall be camouflage green #483 for Class I and tan #380 for Class 2, and the colorfastness requirements shall not apply. 3.3.6 Suspender hardware. 3.3.6

29、.1 Fastener (side release). The fastener (side release) shall meet the requirements of U.S. Army Natick Research Development and Engineering Center Drawing 5-10-47. The fastener shall be made from Black Acetal Delrin plastic (See 6.7). 3.3.6.2 Slide (triqlide). The slide (triglide) shall meet the re

30、quirements of the U.S Army Natrick Research Development and Engineering Center Drawing Number 2-6-102. The slide shall be made from Black Acetal Delrin plastic (See 6.7). Y 3.3.7 Tape 3.3.7.1 Suspender strap tapes. The suspender strap tape shall be type I, class -8, one inch width. The color shall b

31、e camouflage green #483 for Class I and tan #380 for Class II conforming to MIL-T-43566 except that the colorfastness requirements shall not apply 3.3.8 Thread. 3.3.8.1 Cotton or rayon wrapped polyester core thread. The cotton or rayon wrapped polyester core threads for seaming and stitching the coa

32、t and trousers shall be ticket Nos. 30, 50 and 70, 2 ply conforming to MIL-T-43548. 3.3.8.2 Color. The thread color shall be camouflage green #483 (color chip #34094 of FED-STD-595) for Class I and khaki P-1, cable #66019, for Class II and the colorfastness requirements shall not apply. The thread u

33、sed to sew the laminate cloth for the lining may be white where not exposed to outside. 3.3.8.3 Water repellant treatment. The cotton or rayon polyester core thread shall be water repellant treated conforming to type II, class 3, of MIL-T-3530. Lubrication of the quarpel treated thread by any means

34、in the end item fabricators plant prior to or during the sewing is prohibited. 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-S-29461 84 999990b 0533992 8 MIL-S-29461 3.3.9 Labels. All clothing labels shall be in accordance with DDD-L-20. Each

35、 pair of trousers and coat shall have an identification, size and instruction label. These three labels may be combined. The color shall be white and the colorfastness requirements shall not apply. 3.3.9.1 Identification label. The identification label shall conform to type VI, class 1 of DDD-L-20,

36、except that the surveillance marking requirements of the laminated cloth shall appear near or under the last line of inscription on the label. The surveillance marking may be hand printed or stamped. characters for the lot number shall be a minimum of 10 points affixed with Black (No. 37038) ink con

37、forming to type I of TT-I- 1795. Size of 3.3.9.2 Size label. The size label shall conform to type VI, class 2 of DDD-L-20. 3.3.9.3 Instruction label. The instruction label shall conform to type VI, class 3 of DDD-L-20 and shall include the following instructive information for each respective size.

38、Instructive information shall be printed in letters not less than a minimum 10 point (approximately 1/8 inch). The instruction label shall be centered below the combination size and contractors label and stitched on all four sides. Chemical and Bioloqical Protective Suit (Carbon Sphere) 1. Wear as o

39、utergarment layer of clothing for protection against chemical agents. Number 2 shall be as follows for each separate size. 2. The multisize system permits the size small to be worn by an individual with height/chest measurements of 53“/36“. 2. The multisize system permits the size medium to be worn

40、by an individual with height/chest measurements of 57“/39“. 2. The multisize system permits the size large to be worn by an individual with height/chest measurements of 511“/39“. 2. The multisize systems permits the size extra large to be worn by an individual with height/chest measurements of 63“/4

41、2“. 3. DO NOT REMOVE THIS LABEL 3.3.9.4 Combination label. Size, identification and instruction labels may be combined conforming to typeVI, class 14 of DDD-L- 20 except that the lot number of the laminated cloth shall appear under the last line of inscriptions on the label and may be hand printed o

42、r stamped. Size of characters for the lot number shall be a minimum of 10 points affixed with Black (No. 37038) ink conforming to type I of TT-1-1795. 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-S-29461 84 9999906 0533993 T MIL-S-29461 3.4

43、Desiqn. 3.4.1 Coat. The coat shall be of a hip length design with integrated hood and full length sleeves with adjustable tab and fastener tapes. The coat shall have two breast pockets, a slide fastener front closure with full length fastener tapes and elastic drawcords in the hem and hood. 3.4.2 Tr

44、ousers. The trousers shall have a gusset on each side of the waist, two bellow type pockets with flaps located at the side, waist adjustment straps and suspenders. Each leg shall have an adjustment tab at the outside to control the adjustment opening. 3.5 Patterns. Standard patterns, which provide 1

45、/2 2 1/8 inch seam allowance for double lapped and double stitched seams of coat and trousers, and 3/8 i 1/8 inch seam allowance for single needle seams, except where otherwise specified, will be furnished by the Government. The standard patterns shall not be altered in any way and are to be used as

46、 a guide for cutting the contractors working patterns. The working patterns shall be identical to the standard patterns. 3.5.1 List of pattern parts. The components of the suit shall be cut from the materials as specified in accordance with the , pattern parts indicated in Table I. 7 Provided by IHS

47、Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-S-29461 Table I. Required Patterns Material Nomenclature of parts Cut parts Outer shell MIL-C-43468 Lining MIL-C-29462 COAT Top sleeve elbow patch Under sleeve elbow patch Front Back Hood center panel Hood side pa

48、nel Top sleeve Under sleeve Chest pocket Breast pocket Breast pocket flap Sleeve tab Front Back Hood side panel Top sleeve Under sleeve Hood center panel 2 2 2 1 1 2 2 2 2 2 2 2 Mat er ia 1 Nomenclature of parts Cut parts Outer shell MIL-C-43468 Lining MIL-C-29462 TROUSERS Side Cargo pocket facing C

49、argo pocket Carg.0 pocket flap Knee patch Gusset Waist tab Leg tab Bib Side Gusset Bib 2 2 1 3.6 Construction. 3.6.1 Stitches, seams and stitchinq. Stitch, seam and stitching types specified in Table II shall conform to FED-STD-751. two or more methods of seams or stitch types are given for the same operation, any one may be used. Where stitch type 401 is used, the looper, that is the underthread, shall be on the inside of the coat a