DLA MIL-S-37988-1985 SURVIVAL KIT INDIVIDUAL TROPICAL TACTICAL AIR CREW IN PLASTIC BAG《胶袋装战术空中机组人员热带个人急救装置》.pdf

1、MIL-S-37 9 8 8 (DLA-DH) October 2, 1985 MI E% TARY SPEC1 FX CATI ON SURVIVAL BIT, INDIVIDUAL, Tropical,.Tactical Air Crew, in Plastic Bag This limited coordination sui1itar.y spacificatiow ha8 been approved by the Defense Personnel Support Center, 2800 South 20th Street, Philadelphia, PA a coordinat

2、ed military specification, It is subject to modification. However, pending its promulgation as a coordinated military specification, it may be uaed in pxocwement. 19101, but ha8 not been approved for promulgation an 1. SCOPE 1.1 This specification covers a kit containing specified medical and surviv

3、al items intended to sustain the lives of air crewmen under survival conditions in a tropfcal climate. 2. APPLICABLE DOCUMENTS 2.1 Issues of documents. The following documents of the issue in effect on date of invitation foe bids or-request or proposal, form a part of this specification to the exten

4、t specified herein: SBEC%PICATPONS L-P-378 - Plastic Sheet and Strip, Thin Gauge, Polyolefin FSC 6545 Licensed by Information Handling ServicesMfL-S-37988 (DU-DM) SP ECI F ICATI ONS FEDERAL EE-M-301 - Match, Safety and Match, Non-Safety UU-C-282 - Chipboard PPP-8-636 - Boxerr, Shipping, Fiberboard .

5、 (Strike Anywhere) MZLITARY MIL-C-5040 - Cord, Nylon MPL-C-43352 - Cloth, Netting, Nylon, Tulleo Tricot MI LI TARY I MIL-STD-105 - Sampling Procedures and Tables for MIL-STD-129 inspection by Attributes - Marking for Shipment and Storage DRAWINGS Defense Personnel Support Center (DPSC) 24357 Mosquit

6、o Headnet and Mittens required by suppliers in connection with specific procurement functions should be obtained from the procuring activity or as directed by the contracting officer.) (Copies of specifications, standards, drawings and publications 3. REQUIREMENTS 3.1 Components. The survival kit sh

7、all consist of a Polyolefin 3a%al plastic bag packed with th items listed on Figure 1. The polyolefin plastic bag shall be NSN 8105-00-83 STbC, POLYOLEFIN, INTERLOCK SEAL CLOSURE FASTENING, 6 inches by 6 inches. Government as indicated in 3.3.1. those used shall be of the highest commercial quality

8、and entirely suitable for the purpose intended. The bag shall be furnished by the 3,2 Materials. When materials are not specifically designated, -2- Licensed by Information Handling ServicesMIL-S-37 9 8 8 ( DU-DM) 6545-01-120-2632 CURPTIVAL AIT, INDIVIDUAL TROPICAL, TACTICAL AIR CREW, XN PLASTIC BAG

9、 CONTRACTOR CONTRACT NO. LIST OF CONTENTS AM) INSTRUCTIONS FOR USE FIGURE 1 LIST OF CONTEMS AND PNSTRUCTIQNS FOR USE Licensed by Information Handling ServicesMIL-S-379 88 (DU-DM) FIGURE 1 (CONTINUED) LSST OF CONTENTS AND INSTRUCTIONS FOR USE -4- Licensed by Information Handling ServicesHI L-S-37 98

10、8 (DLA-DH) 3.2,4 Polyethvlene bass. The polyethylene bags used to contain individual components Bhall be fabricated of clear natural lay-flat tubing conforming to the requirements of L-P-378, type I, clase 1. The minimum average wall thicknesa of the bag shall be 0.003 inch with no less than 80 perc

11、ent of the nominal wall thickness at any point. Both seam and closure shall be beat-Bealed to prevent moisture from entering or to prevent escape of fluid contents dn the event ob leakage1 excess air shall have been excluded from the sealed Bag 80 that bag conforms to the shape sf the component ther

12、ein. To insure a minimum of excess material, the width of commercially available tubing shell be of a dimension which shall closely Ebt the individual component to be enclosed. shall be the minimum to contain the component. Excess tubing beyond the seals shall be cut Off, item shall be capable of pa

13、ssing the leakage test specified in 4.4.1 The length of the tubing between seals Each sealed bag containing an individual 3.3 Kit contents. 3.3.1 Government furnished components. The components listed below shall be furnished to the contractor by the Government. contractor shall determine that each

14、component is readily identifiable. On receipt of the required quantity of each of the potency dated components, the contractor shall determine from the marked expiration date(s) that at least 12 monthe potency remains beyond his predetermined asssplbly date. The NSN - 6505-00-118-1914 6505-00-118-19

15、48 6585-00-148-7896 6505-80-183-9419 6505-00-913-7985 6510-00-054-7255 6510-00-913-7906 e Expiration Dated Item Identification Potency (Pl Items Diphenoxyate Hydrochloride and P Aspirin Tablets, USP, 0,324 Gram, 100s P Bovbdone - Iodine Qintment, 108,. %r Atropine Sulfate Tablets, USP., 100s 118 oz,

16、 (3.5 Game), Individually Sealed, 3.488 Sulfacetamide Sodium Ophthalmic P Chloroquine and Primaquine Phosphates Skin Cloeure Adhesive, Surgical, Porous P Ointment, USP, 1Q%, 1/8 oz. (3.5 Grams) Tableta, 150s 114 by 4 inchea, 500s 2 inches by 5 yards, 50s Bandage, Gauze, Elastic, Two-ply, -5- License

17、d by Information Handling ServicesMIL-S-37988 65 777490b 0946020 5 W MIL-S-37988 (DIA-DM) - NSN Item identification Expiration Date d Potency (PI Items 6510-00-913-7909 Bandage, Adhesive, 3/4 by 3 inches, 300s * 6515-00-926-2089 Razor, Surgical Preparation, Straight Typer Small 6695-00-118-2918 Bag,

18、 Food Sample, Polyethylene, Disposable, 18 fl. oz Capacity, 500s SOS 6850-00-965-7166 Water Purification Tablets, Iodine, 8 mg. * 8105-OU-837-7754 Bag, Plastic, Polyolefin, Interlock *+ Seal Closure Fastening, (i inch by 6 inch 10008 *Difference between predetermined date of assembly and date of *No

19、t less than 12 months remaining from predetermined assembly manufacture shall not exceed 23 months. date to retest date. *Managed by General Services Administration (GSA). 3.3.2 Contractor-furnished items. The items specified herein shall be furnished by the contractor, 3.3,2.1 Bar of soap. The bar

20、of soap shall be nominal 1/2 ounce (14 gram) bar of unscented, commercially-available oap, having nominal dimensions of 1/4 by 1-1/4 by 2 inches, and wrapped in paper, marked with the name of the contents, “SOAP“. Commercial wrapping and marking shall be acceptable. consist of a mosquito-proof headn

21、et and two mittens. The headnet and mittena shall be fabricated of black, nylon tulle tricot cloth conforming to the requirements of MIL-C-43352, class 2. Construction shall be in accordance with DPSC Drawing 24359. Finished dimensions shall be obtained without stretching the cloth. 3.3.2.2 Readnet

22、and mittens. The headnet and mittens shall -6- Licensed by Information Handling ServicesMIL-S-37 98 8 (DLA-DW 3.3.2.3 Plexible 8aw. The flexible saw shall be fabricated from three 0.015 2 .O02 inch thick ateel strips. Bhall be 0,080 2 ,005 inch wide and glhall contain teeth. strip shall be 0.050 .)

23、,005 inch wide, and ahall have no teeth, Each outer strip shall have approximately 16 teeth to the inch, each tooth having a depth of approximately 0.030 inches. laid flat and twisted together, the outer strips entwined about the inner strip, with a pitch 2 to I times their width. cutting teeth shal

24、l project in opposite cutting directions to provide cutting in any direction, The twisted saw blade shall have nominal 1/16 inch core diameter. A 0.175 + 0.010 inch inside diameter brass eyelet shall be permanently fitted-to each end of the blaUe. The overall length of the saw, including eyelets, 8h

25、alf be 16 inches 4 1/2 inch. The 8aw blade, including eyelets, shall be cadmium plated. 3.3.2.4 Matchest safetvt humidity, resistant, 20s. The matches shall conform to the requirements of EE-M-101, type II, class 2, An assembled booklet shall be 2 + 118 inches long, 1-112 2 1/8 inches wide, and 1/4

26、- + 118 inch thick at the match tip end of the booklet. follows: The two outer stpipe The inner The stripe shall be The inclined The cover of each booklet of matches shall be legibly marked as MATCHES Store in plastic bag , when not in u8e 3,3,2.S List of contents and instructions. A list of content

27、s and instructions for use shall consist of a list of components for the assembly and the quantity of each component. The list shall reflect the usage and dosage for each item, when applicable, as shown on Figure 1. The information shall be printed in black on both sides of one OP: more white cards.

28、 Printing shall be not l&s than 6 point akandarrd gippec cam type size to asaure legibility in reduced light. The neme of the manufacturer or contractor, contract number# and %vatbonal 8toek Nmbes bahall be placed on the front of the first card. The prnted cazda hall be laminated in clear plastic. T

29、he laminated cards shall be na larger than 4-112 inches long by 3 inches wide, shall be completely sealed, and shall not separate. When two or more cards are required, the cards shall be stapled at the upper left corner with 8 monel staple. As &n alternate, the foregoing in8orrnation shall be printe

30、d with waterproof ink on a strip of waterproof paper. larger than 4-112 inches long by 3 inches wide. The list of contenta and instructions shall be capable of passing the test epccified in The paper shall be Zolded to form a pbamphlct no 4e4.2. 3.5 Preparation for assembly, Preparation for assembly

31、 of the items designated herein shall be as follows: * -7- , Licensed by Information Handling ServicesMIL-S-37788 b5 777770b OLtYb02Z 7 MI L-S-37 9 8 8 (DLA-DM) 3.5-1 Preparation of items furnished in stripforrn. The contractor shall*detach the required number of tablets, as applicable, in a continu

32、ous strip from the strips furnished by the Government. Detached continuous aluminum foil strips shall be examined visually to insure that heat seals are not broken 01: fol1 is not torn before insertion in the kit. Strips of the following components shall be folded to form a packet of suitable size a

33、nd secuted in the middle by a neoprene rubber band: NSN Identification - 6505-00-118-1914 6505-00-118-1948 6505-00-913-7905 No. in strip 10 10 2 Brief ften Diphenoryl at e Tablets Aspirin Tablets. Chloroquine and Primoquine Tablets. 3.5.2 Preparation of other components. 3.5.2.1 Baq, food sample, po

34、lyethylene, disposable, 18 fl. oz. capacity, 500s. A unit of 500 food sample bags shall be opened. contractor shall count out and stack 3 bags high with ties at the top. Each stack shall be folded on itself in such a manner that the 3 bottoms are aligned with the 3 tops, and then folded in half on i

35、tself again to form ZL package approximately 4-1/2 inches wide and 2-318 inches long. To secure the package, the 3 ties protruding from the right side shall be bent 180 degrees clockwise, and the 3 ties on the left side shall be bent 180 degrees counterclockwi8,c. diameter, fabricated f olive drab N

36、o, 7 nylon cord conforming to type 1% of M1E-C-54Qp shall Be tied in each eyelet at the ends of the 8aw by meane of a non-%lippable knot, Core lines shall be removed from cord prior to forming loop. Strands of cord ends shall be fused. The complete saw shall be uniformly formed around 1/4 inch diame

37、ter mandrel into long, narrow loops making a flat unit 1/2 inch 5 118 inch wide by 3-112 inche8 & 1/8 inch long, packaged in 3 inches 2 1/8 inch by 4 inches 2 1/8 inch chipboard folded along the centerline of the long s.ideo chipboard package shall be secured by a single staple. Chipboard shall conf

38、orm to the requirements of OU-C-282, 0.026 inch average thickness. shall be adhered to the chipboard package. The chipboard package shall be sealed in a polyethylene bag as specified in 3.2.4. alternate, the label shall be inserted within the rilastic baa used to 3.5.2.2 Flexible saw. A loop 1-1/2 i

39、nches 2 1/4 inch internal The formed saw shall be The open aide of the A label bearing the legend SAW, FLEXIBLE, 16 inchas Long” A8 an ._ - contain the chipboard package in such a manner thai It is legible through the bag. -8- Licensed by Information Handling ServicesMIL-S-37 98 8 (DLA-DH) 3.5.2.3 H

40、eadnet and mittens. The completed mosquito headnet and mittens shall be folded and compressed into & rectangular package with the bo%lowing maximum dimensionas 2-9/16 inches by 2-5/16 inches by 3/4 inch, mittens in the compression process. Each compressed packsge shall be placed in a bag made of cle

41、ar polyethylene as specified in 3.2.4. Closure shall be heat-sealed te prevent moisture from entering the bag. Mosquito Headnet and Mittens, Nylon“. As an alternate, the legend shall be printed on a label which shall be inserted in the plastic bag in auch a manner that it is legible through the bag.

42、 Care shall be taken to prevent damage to the headnet and Each individual bag shall be marked with the legend: 3.5.2.4 Povidone-Iodine Ointment. Each packet of povidone-iodine ointment ohall be sealed in a polyethylene bag as epacified in 3.2.1. Individually-sealed packets shall then be divided into

43、 two 5-packet lots. Each S-packet lot shall be secured with a neoprene rubber band. 3.5.2.5 Other items. The following items shall be packaged in accordance with 3.2.4: ITEM QUANTITY PER BAG 3,6 Assembly, The List ob Contents c Instructions for u8e and a11 components listed in Figure 1 shall be pack

44、ed in the polyolefin plastic bag in a neat and oa.der%y manner to provide as flat a package s possible. . The ointment and tablet items shall be placed in the center of the bag, surrounded by the remaining components for protection. 3.7 Workmanship. Workmanehip shall be first class throughout. %he i

45、ndividual components, a6 well as the completely assembled kits, shall be free from defects which detract from their appearance or may impair their serviceability. -9- a Licensed by Information Handling Services ._ MIL-S-37788 65 997970b OYLlb024 2 . MI L-S-37 9 8 8 (DLA-DM) 4 QUALITY ASSURANCE PROVI

46、SIONS 4.1 Reponsibility for Inspection. Unless otherwise specified in the contract or purchase ordero the supplier ia responsible for the performance of all inspection requirements as specified herein. Except CIS otherwise specified in the conttact or purchase arder, the supplier may use his own or

47、any other facilities suitable for the pezformance of the inspection requirementa specified herein, unless disapproved by the Government. The Government rebervts the right to perform any of the inspectione set forth in the apccification where auch inspections are deemed necessary to assure eupplica a

48、nd setvices conform to prescribed requirements. 4.1.1 Records. Recorde of examinations and tests performed by OP for the contractor shall be maintained by the contractor and made available to the Government, upon the Governments request, at any time, or from time to time, during the performance of t

49、he contract and for a period of three years after delivery of the supplies to which such records relate. 4.1.2 Inspection, Inspection, as used in this specification, is defined as both examination (such as visual or auditory investigation without the use of special laboratory appliances or procedures) and testing (determination by technical meana of phyaical and chemical properties) of the item. by the manufacturer of the Beanet and mittens, liet of contenta, matches, and polyethylene bags may be furnished in lieu of actual performance of testing by the contractor, pro