DLA MIL-STD-13231 CHANGE 1-2013 MARKING OF ELECTRONIC ITEMS.pdf

1、 DEPARTMENT OF DEFENSE STANDARD PRACTICE MARKING OF ELECTRONIC ITEMS AMSC N/A FSC MISC MIL-STD-13231 w/CHANGE 1 18 November 2013 SUPERSEDING MIL-STD-13231 2 November 1999 INCH-POUND Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-STD-13231 w/CHAN

2、GE 1 ii FOREWARD 1. This standard is approved for use by all Departments and Agencies of the Department of Defense. 2. This standard provides uniform marking requirements for electronic items. 3. Comments, suggestions, or questions on this document should be addressed to Commander, DLA Land and Mari

3、time, ATTN: VAI, P.O. Box 3990, Columbus, Ohio, 43218-3990 or emailed to Sounddscc.dla.mil. Since contact information can change, you may want to verify the currency of this address information using the ASSIST Online database at https:/assist.dla.mil. Provided by IHSNot for ResaleNo reproduction or

4、 networking permitted without license from IHS-,-,-MIL-STD-13231 w/CHANGE 1 iii CONTENTS PARAGRAPH PAGE FOREWARD - ii 1. SCOPE - 1 1.1 Scope - 1 2. APPLICABLE DOCUMENTS - 1 2.1 General - 1 2.2 Government documents- 1 2.2.1 Specifications, standards, and handbooks - 1 2.2.2 Other Government documents

5、, drawings, and publications - 2 2.3 Non-Government publications - 2 2.4 Order of precedence - 2 3. DEFINITIONS- 3 3.1 Assemblies - 3 3.2 Commercial and Government Entity (CAGE) - 3 3.3 Commercial off the shelf (COTS) products (also referred to as commercial products) - 3 3.4 Container- 3 3.5 Decalc

6、omania- 3 3.6 Design activity - 3 3.7 Document - 3 3.8 Functional marking - 3 3.9 Joint electronics type designation systems- 3 3.10 Manufacturer - 3 3.11 Manufacturers identification - 3 3.12 NATO supply code for manufacturers (NSCM) - 3 3.13 Nomenclature - 3 3.14 Order of precedence - 3 3.15 Part

7、or Identifying Number (PIN) - 4 3.16 Procurement instrument identification number (PIIN) - 4 3.17 Sets- 4 3.18 Selected item drawing - 4 3.19 Sequence of markings - 4 3.20 Units - 4 4. GENERAL REQUIREMENTS - 4 4.1 General - 4 4.2 Nomenclature - 4 4.2.1 Government names and type numbers - 4 4.2.1.1 J

8、oint electronics type designation systems- 4 4.2.1.2 Army nomenclature systems - 4 4.2.2 Identifying number - 4 4.2.3 Procurement instrument identification number - 4 4.2.4 Inspectors stamp - 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-STD-

9、13231 w/CHANGE 1 iv CONTENTS PARAGRAPH PAGE 4.2.5 Special characteristics - 5 4.2.6 Contractor and Government Entity (CAGE) code - 5 4.3 Identification to be marked on equipment - 5 4.3.1 Exceptions to table I- 5 4.3.2 Uniquely small items - 5 4.3.3 Limited use / multiple use - 5 4.3.4 Specific item

10、 identification - 7 4.3.5 Use of unit pack/bag and tag - 7 4.4 Reference designations, government type numbers and - designators for parts assemblies - 7 4.4.1 Reference designations - 7 4.4.1.1 Reprocurements - 7 5. DETAIL REQUIREMENTS - 7 5.1 Type numbers and type designation - 7 5.1.1 Electron tu

11、bes - 7 5.1.2 Electrical / electronic parts and printed wiring boards - 7 5.1.3 Nameplate data for articles of equipment - 7 5.2 Special requirements for marking of containers - 7 5.2.1 Identification of set, article of equipment, or contents - 7 5.2.2 Identification of container only - 8 5.3 Specia

12、l markings on articles of equipment - 8 5.3.1 Marking battery circuits - 8 5.3.1.1 Warning label - 8 5.3.2 High voltage notice - 8 5.3.3 Radioactive material - 8 5.3.4 Non-ionizing radiation- 8 5.3.5 Technical literature caution notice - 9 5.3.6 Schematic, wiring, and cable diagram - 9 5.3.7 Chassis

13、 identification - 9 5.3.8 Modification work-order number - 9 5.3.9 Sensitive electronic devices - 9 5.4 Location of marking - 10 5.4.1 General - 10 5.4.2 Type number and type designations - 10 5.5 Marking processes - 10 5.6 Marking on wood surfaces- 10 5.6.1 Exterior wood containers- 10 5.6.2 Other

14、wood surfaces - 10 5.6.3 Branding- 10 5.7 Size and form of characters - 10 5.8 Labels - 10 5.8.1 Border- 10 5.8.2 Material and process - 11 5.8.3 Radius of corners - 11 5.8.4 Mounting - 11 5.9 Spectral gloss - 11 5.10 Opacity - 11 5.11 Permanency, durability, and legibility - 12 5.11.1 Permanency, d

15、urability, and legibility tests - 12 5.12 Facsimiles - 13 5.13 Workmanship - 14 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-STD-13231 w/CHANGE 1 v CONTENTS PARAGRAPH PAGE 6. NOTES - 14 6.1 Intended use - 14 6.2 Acquisition requirements - 14 6

16、.3 Marking for shipment- 14 6.4 Serial numbers - 14 6.5 Air-transportable items - 14 6.6 Reprocurements - 14 6.7 Subject term (key word) listing - 14 6.8 Assemblies, sets, and units - 14 6.9 Environmentally preferable material - 14 6.10 Change notations - 15 FIGURES 1. Name and caution plate (exampl

17、e legend) - 9 2. Caution plate - 9 TABLES I. Priority of identification information on parts and assemblies - 6 II. Marking process- 13 CONCLUDING MATERIAL- 15 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-STD-13231 w/CHANGE 1 1 1. SCOPE 1.1 Sc

18、ope. This standard covers the general requirements for marking of electronic items, except marking for shipment and as otherwise specified by an applicable Government document covering the item on which the marking appears. These requirements cover both the information to be shown by the marking and

19、 the materials and processes used therefor. This standard should be implemented by incorporating suitable requirements directly in acquisition documents. 2. APPLICABLE DOCUMENTS 2.1 General. The documents listed in this section are specified in sections 3, 4, and 5 of this standard. This section doe

20、s not include documents cited in other sections of this standard or recommended for additional information or as examples. While every effort has been made to ensure the completeness of this list, document users are cautioned that they must meet all specified requirements of documents cited in secti

21、ons 3, 4, and 5 of this standard, whether or not they are listed. 2.2 Government documents. 2.2.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of th

22、ese documents are those cited in the solicitation or contract. FEDERAL SPECIFICATION L-P-535 - Plastic Sheet (Sheeting): Plastic Strip Poly (Vinyl Chloride) and Poly (Vinyl Chloride-Vinyl Acetate), Rigid. COMMERCIAL ITEM DESCRIPTIONS A-A-208 - Ink, Marking, Stencil, Opaque (Porous and Non-Porous Sur

23、faces). A-A-56032 - Ink, Marking, Epoxy Base DEPARTMENT OF DEFENSE SPECIFICATIONS MIL-DTL-14072 - Finishes for Ground Based Electronic Equipment MIL-DTL-19834 - Plate, Identification, Metal foil, Adhesive Backed MIL-I-24092 - Insulating Varnishes and Solventless Resins for Application by the Dip Pro

24、cess MIL-PRF-31032 - Printed Circuit Board / Printed Wiring Board, General Specification for DEPARTMENT OF DEFENSE STANDARDS MIL-STD-129 - Military Marking. MIL-STD-130 - Identification Marking of U.S. Military Property MIL-STD-196 - Joint Electronics Type Designation System (JETDS) MIL-STD-202 - Te

25、st Methods for Electronic and Electrical Component Parts MIL-STD-810 - Environmental Engineering Considerations and Laboratory Tests MIL-STD-1285 - Marking of Electrical and Electronic Parts MIL-STD-1464 - Army Nomenclature System (Copies of these documents are available online at http:/quicksearch.

26、dla.mil or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-STD-13231 w/CHANGE 1 2 2.2.2 Other Government documents, drawings, and publica

27、tions. The following other Government documents, drawings, and publications form a part of this document to the extent specified herein. Unless otherwise specified, the issue are those cited in the solicitation. H4/H8 Section A - Commercial and Government entity (CAGE) (Name to Code). (Cataloging Ha

28、ndbook H4/H8 is available online at http:/www.dlis.dla.mil/hseries.asp, email dlacontactcenterdla.mil, or contact Commander, Defense Logistics Service Center, ATTN: DLSC-WP, Federal Center, Battle Creek, MI 49037-3084.) 2.3 Non-Government publications. The following documents form a part of this doc

29、ument to the extent specified herein. Unless otherwise specified, the issues of the documents are those cited in the solicitation or contract. ASME INTERNATIONAL ASME Y14.44 - Reference Designations for Electrical and Electronics Parts and Equipment (Copies of this document are available online at http:/www.asme.org or from the ASME International, Three Park Avenue,