DLA MIL-STD-1531 A-1988 INSERT ARRANGEMENTS FOR MIL-C-83733 RACK TO PANEL CONNECTORS SHELL SIZE A《A规格机体壳的MIL-C-83733型机架至面板连接器的板孔排列》.pdf

1、MIL-STD-1531 A(USAF) 25 MAR 1988 SUPERSEDING 1 OCTOBER 1972 MIL-STD-1531 (USAF) MILITARY STANDARD INSERT ARRANGEMENTS FOR SHELL SIZE A MIL-C-83733 RACK TO PANEL CONNECTORS, r THIS DOCUMENT CONTAINS /7 PAGES. ,- 1- FSC 5935 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimi

2、ted. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- MIL-STD-L53LA 57 m 77777LL 0008878 T m MI L-STD- 1531A( USAF ) DEPARTMENT OF DEFENSE Washington, D.C. 20301 Insert Arrangements for MIL-C-83733 Rack to Panel Connectors, Shell Size A 1. This Milit

3、ary Standard is approved for use by the Department of the Air Force. 2. Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document should be addressed to 2750 Air Base Wing (AFLC), ATTN: ES, Gentile Air Force Station, Dayton, Ohi

4、o 45444 by using the self-addressed Standafdization Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter. B 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-1. 1.1 2. 2.1 2.1.1 3. 3.1 4. 5. 5.1 5.2 5.3 6. 6

5、.1 6.2 CONTENTS MIL-STD-l53lA(USAF) .- a, FIGURE 1 Dimensions and configurations- - - - - - - - - - - - - - . iii/iv Page 1 - 1 1 1 1 1 1 1 1 1 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-STD-153LA 57 779771L 0008900 4 1. SCOPE 1.1 Scope. T

6、his standard covers insert arrangements for use with MIL-C-83733 rack to panelnectors, shell size A. It is used to control the dimensions and configuration of insert patterns and the contact sizes. 2. REFERENCED DOCUMENT 2.1 Government document. 2.1.1 Specification. The following specification forms

7、 a part of this standard to the extent specified herein. Unless otherwise specified, the issue of this document shall be that listed in the issue of the Department of Defense Index of Specification and Standards (DODISS) and supplement thereto, cited in the solicitation. SPECIFICATION MILITARY MIL-C

8、-83733 - Connectors, Electrical, Miniature, Rectangular Type, Rack to Panel, Environment Resisting, 200 C Total Continuous Operating Temperature, General Specification For. (Copies of the specification required by contractors in connection with specific acquisition functions should be obtained from

9、the contracting activity or as directed by the contracting activity.) 3. DEFINITIONS 3.1 Definitions. The terms used in this standard are generally accepted by the electrical and electronics industries and commonly used in electrical connector engi neeri ng practice. 4. GENERAL REQUIREMENTS: Not app

10、licable. 5. DETAIL. REQUIREMENTS 5.1 Dimensions. Dimensions shall be in accordance with figure 1. 5.2 Markin . Marking shall be in accordance with MIL-C-83733 and as shown on figure 19 * 5.3 Drawing notes. Unless otherwise specified, the following information is applicable to all figures of this mil

11、itary standard. a. Dimensions are in inches. b. Metric equivalents are given for general information only. c. Unless otherwise specified, tolerances are I.005. 6. NOTES * 6.1 Subject term (key word) listing. Connectors, rack to panel Connectors, MIL-C-83733 Insert arrangements 6.2 Changes from previ

12、ous issue. The margins of this standard are marked with asterisks to indicate where changes (additions, modifications, corrections, deletions) from the previous issue were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notat

13、ions. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations and relationship to the last previous issue. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-

14、MIL-STD-LS3LA 57 7 MIL-STD-l531A( USAF) - f Inches mm .122 .194 ,244 .366 .488 .610 .732 -T 3.10 4.93 6.20 9.30 12.40 15.49 18.59 I Quantity I Service I Contact I Sire I Shell I Y I I size I I I I I I I I I 18 I I I All I#l2I A I I I I I I I I* I rating k.7 3 2 +,6 I O 4 018 LAYOUT FACE VIEW PIN INS

15、ULATOR II Inches mm .O76 1.93 .O88 2.24 .175 4.44 .228 5.79 .263 6.68 .350 8.89 .438 11.13 .525 13.34 ,613 15.57 .700 17.78 fy.350 I I 032 LAYOUT FACE VIEW PIN INSULATOR I I I I I I I Ouantitv I Service I Contact I Size I Shell I I I 1 size I I rating I I I I I I I 32 I I I All 1#161 A I I I I I I I

16、 FIGURE 1. Dimensions and configurations. 2 /- - -_ Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-STD-II53LA 59 m 99999LL 0008902 m MIL-STD-l53lA(USAF) mm Inches Inches mm .O71 1.80 .357 9.07 .122 3.10 .429 10.90 .143 3.63 .500 12.70 .214 5.44

17、.572 14.53 ,244 6.20 .643 16.33 .286 7.26 .715 18.16 T I I I III. FACE VIEW PIN INSERT 051 LAYOUT I I I I I I I Quantity I Service I Contact I Size I Shell I I I rating I I I size I I I I I I I I 51 I I I All I #20 I A I I I I I I I I I I Inches .O45 .O78 . O90 .135 .156 FACE VIEW PIN INSERT 131 LAY

18、OUT FIGURE 1. mm 1.14 1.98 2.29 3.43 3.96 4.57 5.72 5.97 Inches .270 .312 .3w .468 .546 .624 .702 .780 mm 6.86 7.92 9.91 11.89 13.87 15.85 17.83 19.81 L.090 I I I I I I I Quantity I Service I Contact I Size I Shell I I I rating I I I size I I I I I I I I I I I I 131 I M I All I #220 I A I I I I I I

19、I Dimensions and configurations - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-STD-1531A 59 m 9999911 0008903 T MIL-STD-l531A(USAF) Custodian: Air Force - 85 Review ac ti vi ti es : Air Force - JO, 82, 99 User activity: Air Force - 11 Preparing activity: Air Force - 85 Agent: DLA - ES (Project 5935-F296) 4 % Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-