DLA MIL-STD-290 H-2013 PACKAGING AND MARKING OF PETROLEUM AND RELATED PRODUCTS.pdf

1、AMSC N/A AREA PACK INCH-POUND MIL-STD-290H 13 May 2013 SUPERSEDING MIL-STD-290G 30 March 2009 DEPARTMENT OF DEFENSE STANDARD PRACTICE PACKAGING AND MARKING OF PETROLEUM AND RELATED PRODUCTS Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-STD-290H

2、 ii FOREWORD 1. This standard is approved for use by all Departments and Agencies of the Department of Defense (DOD). 2. This standard should be used in conjunction with the joint DoD publication AFMAN24-204 “Preparing Hazardous Material for Military Air Shipments“, International Civil Aviation Orga

3、nization (ICAO), International Maritime Dangerous Goods (IMDG), Title 49 and Title 29 Code of Federal Regulations, and any other applicable law or regulation required for the safe handling, storage, and transportation of material covered under this standard. 3. Changes in this document are: Revised

4、various citations in 2.2 and 2.3 to reflect current document numbers and names. Document numbers revised throughout standard as required. Added reference to International Maritime Dangerous Code (IMDC) and International Civil Aviation Organization (ICAO) Technical Instructions at multiple locations.

5、 Deleted citation for ANSI/ASME MH1 from Material Handling Industry of America in 2.3. Document is not cited in standard. Updated contact information for Steel Shipping Container Institute and National Rail Freight Committee (Railinc) in 2.3. Revised 5.8.2.e to specify units per exterior pack for li

6、ter containers Revised 5.10.4.4 to reference figure 5 (no reference existed in previous revision) Revised 5.10.13 to bring into conformance with DoD Shelf-Life policies of DoD 4140.27-M and MIL-STD-129. Revised 5.10.30 from Material Safety Data Sheets (MSDS) to Safety Data Sheets (SDS) Added 6.4, In

7、ternational Standardization Agreement note Updated tables IV and V and figures 1-5 to bring into agreement with current standards. Minor typographical, clerical or editorial changes are not listed here. 4. Comments, suggestions, or questions on this document should be addressed to DLA Aviation -VEB,

8、 8000 Jefferson Davis Highway, Richmond, VA 23297-5610 or emailed to STDZNMGTdla.mil . Since contact information can change, you may want to verify the currency of this address information using the ASSIST Online database at https:/assist.dla.mil . Provided by IHSNot for ResaleNo reproduction or net

9、working permitted without license from IHS-,-,-MIL-STD-290H iii CONTENTS PARAGRAPH PAGE FORWARD. ii 1. SCOPE 1 1.1 Scope 1 1.2 Application . 1 1.2.1 Centrally procured items 1 1.2.2 Locally procured items . 1 1.3 Options . 1 2. APPLICABLE DOCUMENTS 1 2.1 General . 1 2.2 Government documents 1 2.2.1

10、Specifications, standards, and handbooks 1 2.2.2 Other Government publications . 3 2.3 Non-Government publications . 3 2.4 Order of precedence . 5 3. DEFINITIONS . 5 3.1 Abbreviations 5 3.2 Commercial packaging . 6 3.3 Containers . 6 3.4 Unit pack 7 3.5 Exterior pack 7 3.6 Intermediate pack . 7 3.7

11、Level of protection . 7 3.8 Marking 7 3.9 Packing 7 3.10 Shelf life items . 7 3.10.1 Type I shelf life items . 7 3.10.2 Type II shelf life items . 7 4. GENERAL REQUIREMENTS . 7 4.1 Unit containers . 7 4.2 Coating of metal containers 7 4.3 Packaging . 8 4.4 Marking 8 4.4.1 Bar code marking . 8 4.5 Pa

12、lletization 8 4.6 Department of Transportation (DOT) regulations 8 4.7 Reclaimed materials . 8 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-STD-290H iv CONTENTS PARAGRAPH PAGE 5. DETAILED REQUIREMENTS 8 5.1 Packaging products in unit container

13、s 8 5.1.1 Unit pack 8 5.1.2 Intermediate pack . 8 5.1.3 Exterior pack 9 5.1.3.1 Military intermediate packs of filled containers of less than 1-pint capacity 9 5.1.3.2 Military intermediate packs of filled containers of 1-pint capacity and over 9 5.2 Packaging standard grease cartridges (for cartrid

14、ge-type grease guns) 9 5.2.1 Unit pack 9 5.2.2 Intermediate pack . 9 5.2.3 Exterior pack 9 5.2.4 Level B . 9 5.2.5 Minimal 9 5.3 Packaging products in drums . 9 5.3.1 Palletization 10 5.4 Packaging products in pails 10 5.5 Packing products in bottles and jars . 10 5.5.1 Unit pack 10 5.5.2 Intermedia

15、te pack . 10 5.5.3 Commercial unit pack 10 5.5.4 Exterior pack 10 5.5.4.1 Level B . 10 5.5.4.2 Minimal 10 5.6 Packaging of specialty products . 10 5.6.1 Unit pack 10 5.6.2 Exterior pack 11 5.6.2.1 Level B . 11 5.6.2.2 Minimal 11 5.7 Packaging of wax . 11 5.7.1 Unit pack of 1-pound wax cakes 11 5.7.2

16、 Exterior pack 11 5.7.2.1 Level B . 11 5.7.2.1.1 10- and 11-pound wax slabs . 11 5.7.2.1.2 Packaging of solid wax . 11 5.7.2.2 Minimal packing of solid wax 11 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-STD-290H v CONTENTS PARAGRAPH PAGE 5.8

17、Cleaner, lubricant, and preservative (CLP) 11 5.8.1 Unit container sizes of CLP 12 5.8.2 Exterior pack 12 5.8.2.1 Level A . 12 5.8.2.2 Minimal 12 5.9 Exterior color coating of metal containers . 12 5.9.1 General . 12 5.9.1.1 Painting . 12 5.9.2 Hydraulic fluid . 13 5.9.2.1 MIL-PRF-5606 - Hydraulic F

18、luid, Petroleum Base; Aircraft, Missile and Ordnance . 13 5.9.2.2 MIL-PRF-83282 - Hydraulic Fluid, Fire Resistant, Synthetic Hydrocarbon Base, Metric, NATO Code Number H-537 13 5.9.2.3 MIL-PRF-6083 - Hydraulic Fluid, Petroleum Base for Preservation and Operation 13 5.9.2.4 MIL-PRF-46170 - Hydraulic

19、Fluid, Rust Inhibited, Fire Resistant, Synthetic Hydrocarbon Base, NATO Code No. H-544 . 13 5.9.2.4.1 Type I . 13 5.9.2.4.2 Type II 13 5.9.2.5 MIL-PRF-87257 - Hydraulic Fluid, Fire Resistant, Low . 13 Temperature, Synthetic Hydrocarbon Base, Aircraft and Missile 13 5.9.2.6 Hermetically sealed cans 1

20、3 5.9.3 Synthetic lubricating oils 13 5.9.3.1 MIL-PRF-7808 - Lubricating Oil, Aircraft Turbine Engine, Synthetic Base 13 5.9.3.2 MIL-PRF-8188 Corrosion-Preventive, Aircraft Turbine Engine, Synthetic Base . 14 5.9.3.3 MIL-PRF-23699 - Lubricating Oil, Aircraft Turbine Engine, Synthetic Base, NATO Code

21、 Number O-156 14 5.9.3.4 DOD-PRF-85734 - Lubricating Oil, Helicopter Transmission System, Synthetic Base 14 5.9.4 Petroleum lubricating oil 14 5.9.4.1 MIL-PRF-6081 - Lubricating Oil, Jet Engine 14 5.9.4.2 MIL-PRF-87252 - Coolant Fluid, Hydrolytically Stable, Dielectric 14 5.9.5 Brake fluid 14 5.9.5.

22、1 SAE J1703 - Motor Vehicle Brake Fluid . 14 5.10 Marking 14 5.10.1 Marking of materials 14 5.10.2 Labels . 14 5.10.3 Color of markings . 14 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-STD-290H vi CONTENTS PARAGRAPH PAGE 5.10.4 Identification

23、, contract data, and address markings . 15 5.10.4.1 Identification and contract data markings on unit containers of 1-gallon capacity or less . 15 5.10.4.2 Identification and contract data markings on unit and intermediate containers . 15 5.10.4.3 Identification, contract data, and address markings

24、on drums . 15 5.10.4.4 Identification, contract data, and address markings of unit loads 15 5.10.5 Location and sequence of markings . 15 5.10.6 NATO (North Atlantic Treaty Organization) code 15 5.10.7 Military symbol 15 5.10.8 Item description 15 5.10.9 Specification number . 15 5.10.10 Type, class

25、, and grade 16 5.10.11 National stock number (NSN) 16 5.10.12 Military airlift requirements . 16 5.10.13 Shelf life markings . 16 5.10.13.1 Date of manufacture . 17 5.10.14 Batch or lot number 17 5.10.15 Contract number . 17 5.10.16 Qualification number 17 5.10.17 Net weight (of contents) . 17 5.10.

26、18 Regulatory marking and labeling . 17 5.10.19 Proper shipping name . 17 5.10.20 UN/NA (United Nations/North American Hazardous Materials Code) identification number . 18 5.10.21 Other precautionary and statutory markings 18 5.10.22 Flash point and boiling point markings 18 5.10.23 Precautionary ma

27、rking of hazardous and chemical materials 18 5.10.24 Unit of issue 18 5.10.25 Address marking . 18 5.10.25.1 Full carloads and full truckloads 18 5.10.25.2 Less-than-carloads (LCL) and less-than-truckloads (LTL) 18 5.10.26 Gross weight . 19 5.10.27 Cube 19 5.10.28 Contractors name . 19 5.10.29 Retur

28、nable drums deposit marking . 19 5.10.30 Material Safety Data Sheet (MSDS) 19 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-STD-290H vii CONTENTS PARAGRAPH PAGE 6. NOTES . 19 6.1 Intended use 19 6.2 Acquisition requirements . 20 6.3 Subject ter

29、m (key word) listing 20 6.4 International Standardization agreement implementation 20 6.5 Change from previous issue. 20 TABLE PAGE I Unit containers for petroleum and related products . 21 II Classification of cans and requirements for arrangement in interior and exterior packs 24 III Packing arran

30、gement of tubes, bottles, and jars . 24 IV Markings on drums and pails for military and commercial . 25 V Identification and contract data marking on unit and intermediate containers (folding, setup, and fiberboard) . 26 FIGURE PAGE 1 Marking of unit containers (1- gallon or less) for military shipm

31、ents . 27 2 Marking of unit and intermediate packs; military and commercial . 28 3 Marking of closed-head drums . 29 4 Marking of pails for military and commercial . 30 5 Marking of fiberboard exterior packs (military and commercial) 31 CONCLUDING MATERIAL . 32 Provided by IHSNot for ResaleNo reprod

32、uction or networking permitted without license from IHS-,-,-MIL-STD-290H 1 1. SCOPE 1.1 Scope. This standard provides detailed requirements and approved uniform methods for packaging, packing, and marking of petroleum and related products for shipment, handling and storage. 1.2 Application. 1.2.1 Ce

33、ntrally procured items. The level of protection, as well as any special marking requirements, should be incorporated in the appropriate purchasing documents. 1.2.2 Locally procured items. This standard is not mandatory for items locally procured for immediate use. 1.3 Options. Where options are indi

34、cated concerning methods of packaging or designation of the method is not specified in the contract or order, the selection should be at the option of the contractor. 2. APPLICABLE DOCUMENTS 2.1 General. The documents listed in this section are specified in sections 3, 4, or 5 of this standard. This

35、 section does not include documents cited in other sections of this standard or recommended for additional information or as examples. While every effort has been made to ensure the completeness of this list, document users are cautioned that they must meet all specified requirements of documents ci

36、ted in sections 3, 4, or 5 of this standard, whether or not they are listed. 2.2 Government documents. 2.2.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified therein. Unless otherwise specified, the

37、issues of these documents are those cited in the solicitation or contract. INTERNATIONAL STANDARDIZATION AGREEMENTS STANAG 1135 - Interchangeability of Fuels, Lubricants and Associated Products used by the Armed Forces of the North American Treaty Nations FEDERAL SPECIFICATIONS PPP-C-96 - Cans, Meta

38、l, 28 Gage and Lighter PPP-D-705 - Drum, Shipping and Storage: Steel, 16 and 30 Gallon Capacity PPP-D-723 - Drums, Fiber Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-STD-290H 2 PPP-D-729 - Drums, Shipping and Storage, Steel, 55 Gallon (208 Lit

39、ers) PPP-P-704 - Pails, Metal: (Shipping, Steel, 1 through 12 Gallons) FEDERAL STANDARDS FED-STD-313 - Material Safety Data, Transportation Data and Disposal Data for Hazardous Materials Furnished to Government Activities FED-STD-595/11105 - Red, Gloss (OSHA Safety Red/DOT) FED-STD-595/13655 - Yello

40、w, Gloss (OSHA Safety Yellow, ANA 505) FED-STD-595/14110 - Green, Gloss (NASA Safety Medium Green) FED-STD-595/15450 - Blue, Gloss FED-STD-595/17142 - Miscellaneous, Gloss (OSHA Safety Purple) FED-STD-595/17875 - Miscellaneous, Gloss (Insignia White, ANA 511) FED-STD-595/21105 - Red, Semigloss FED-S

41、TD-595/22648 - Orange, Semigloss (Buff) Color names in parentheses are per FED-STD-595, Appendix IV DEPARTMENT OF DEFENSE SPECIFICATIONS MIL-PRF-2104 - Lubricating Oil, Internal Combustion Engine, Combat/Tactical Service MIL-PRF-5606 - Hydraulic Fluid, Petroleum Base; Aircraft, Missile and Ordnance

42、MIL-PRF-6081 - Lubricating Oil, Jet Engine MIL-PRF-6083 - Hydraulic Fluid, Petroleum Base, for Preservation and Operation MIL-PRF-7808 - Lubricating Oil, Aircraft Turbine Engine, Synthetic Base MIL-PRF-8188 - Corrosion-Preventive, Aircraft Turbine Engine, Synthetic Base MIL-PRF-9000 - Lubricating Oi

43、l, Shipboard Internal Combustion Engine, High-Output Diesel MIL-PRF-14107 - Lubricating Oil, Weapons, Low Temperature MIL-PRF-17331 - Lubricating Oil, Steam Turbine and Gear, Moderate Service MIL-PRF-17672 - Hydraulic Fluid, Petroleum, Inhibited. MIL-PRF-21260 - Lubricating Oil, Internal Combustion

44、Engine, Preservative Break-In MIL-PRF-23699 - Lubricating Oil, Aircraft Turbine Engine, Synthetic Base, NATO Code Number O-156 MIL-PRF-46170 - Hydraulic Fluid, Rust Inhibited, Fire Resistant, Synthetic Hydrocarbon Base, NATO Code No. H-544 MIL-PRF-83282 - Hydraulic Fluid, Fire Resistant, Synthetic H

45、ydrocarbon Base, Metric, NATO Code Number H-537 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-STD-290H 3 DOD-PRF-85734 - Lubricating Oil, Helicopter Transmission System, Synthetic Base MIL-PRF-87252 - Coolant Fluid, Hydrolytically Stable, Diele

46、ctric MIL-PRF-87257 - Hydraulic Fluid, Fire Resistant; Low Temperature, Synthetic Hydrocarbon Base, Aircraft and Missile DEPARTMENT OF DEFENSE STANDARDS MIL-STD-129 - Military Marking for Shipment and Storage MIL-STD-147 - Palletized Unit Loads MIL-STD-2073-1 - Standard Practice for Military Packagi

47、ng (Copies of these documents are available online at https:/assist.dla.mil or from the Standardization Document order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2.2 Other Government publications. The following other Government publications form a part of this document to

48、 the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. CODE OF FEDERAL REGULATIONS (CFR) Title 29 CFR - Labor Title 40 CFR - Protection of Environment Title 49 CFR - Transportation (Copies of these documents are available online at http:/www.gpoaccess.gov/ ; from the U.S. Government Printing Office, P.O. Box 979050, S