DLA MS14055 REV J-2009 INSERT ARRANGEMENTS ELECTRICAL CONNECTOR SIZE 44 CLASS L 100 AMPS.pdf

1、 MS14055J 1 April 2009 SUPERSEDING MS14055H 26 October 2005 INCH-POUND DETAIL SPECIFICATION SHEET INSERT ARRANGEMENTS, ELECTRICAL CONNECTOR, SIZE 44, CLASS L, 100 AMPS This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring

2、the product described herein shall consist of this specification sheet and MIL-DTL-22992. Quantity Contact Size Socket SAE-AS39029/49-Pin SAE-AS39029/48-1 A 1/0 333 323 1 N 1/0N 333 (see note 6) 324 NOTES: 1. Dimensions are in inches. Metric equivalents are given for information only. Unless otherwi

3、se specified, tolerance is .002 (.05 mm). 2. Unless otherwise specified, front face of pin insert pattern is shown. Socket inserts are the reverse. 3. -02-Cable IPCEA 2-NO 2 conductor round type W, 0 - 600 volts. 4. -03-Cable-C0-02-HDF (2/1) 1385 in accordance with MIL-DTL-3432. 5. Mark 44-02 on 44-

4、03 insert. Trademark and 44-( ) shall appear in available space. Contact identifying letter shall be located so as to identify relative contact. 6. Only the pin contact is lengthened and has the N (neutral) designation. The mating socket contact is the same as the power contact. 7. The contact posit

5、ion labeled (G) in the insert arrangement contains the 1/0N (neutral) size pin contact that is connected to the shell to form a grounding pin contact. FIGURE 1. 28 volt DC two wire -02 and -03 insert arrangements, service D. AMSC N/A FSC 5935 Provided by IHSNot for ResaleNo reproduction or networkin

6、g permitted without license from IHS-,-,-MS14055J 2Quantity Contact Size Socket SAE-AS39029/49-Pin SAE-AS39029/48-1 A 1/0 333 323 1 N 1/0N 333 (see note 6) 324 2 G1, G2 4G 332 322 NOTES: 1. Dimensions are in inches. Metric equivalents are given for information only. Unless otherwise specified, toler

7、ance is .002 (.05 mm). 2. Unless otherwise specified, front face of pin insert pattern is shown. Socket inserts are the reverse. 3. -04-Cable IPCEA 2-NO 2 conductor round type G, 0 - 600 volts. 4. -05-Cable-C0-02-HDF (2/1-2/5R) 1385 in accordance with MIL-DTL-3432. 5. Mark 44-04 on 44-05 insert. Tra

8、demark and 44-( ) shall appear in available space. Contact identifying letter shall be located so as to identify relative contact. 6. Only the pin contact is lengthened and has the N (neutral) designation. The mating socket contact is the same as the power contact. 7. The contact position labeled (G

9、) in the insert arrangement contains the 1/0N (neutral) size pin contact that is connected to the shell to form a grounding pin contact. FIGURE 2. AC single phase two wire grounding, -04 and -05 insert arrangements, service D. Provided by IHSNot for ResaleNo reproduction or networking permitted with

10、out license from IHS-,-,-MS14055J 3Quantity Contact Size Socket SAE-AS39029/49-Pin SAE-AS39029/48-2 A, B 1/0 333 323 1 N 1/0N 333 (see note 5) 324 3 G1, G2, G3 6G 330 319 NOTES: 1. Dimensions are in inches. Metric equivalents are given for information only. Unless otherwise specified, tolerance is .

11、002 (.05 mm). 2. Unless otherwise specified, front face of pin insert pattern is shown. Socket inserts are the reverse. 3. -06-Cable IPCEA 3-NO 2 conductor round type G, 0 - 600 volts. 4. Mark 44-06 on insert. Trademark and 44-06 shall appear in available space. Contact identifying letter shall be l

12、ocated so as identify relative contact. 5. Only the pin contact is lengthened and has the N (neutral) designation. The mating socket contact is the same as the power contact. 6. The contact position labeled (G) in the insert arrangement contains the 1/0N (neutral) size pin contact that is connected

13、to the shell to form a grounding pin contact. FIGURE 3. AC single phase three wire grounding, -06 insert arrangements, service D. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS14055J 4Quantity Contact Size Socket SAE-AS39029/49- Pin SAE-AS39029/4

14、8- 3 A, B, C 1/0 333 323 1 N 1/0N 333 (see note 6) 324 4 G1, G2, G3, G4 6G 330 319 NOTES: 1. Dimensions are in inches. Metric equivalents are given for information only. Unless otherwise specified, tolerance is .002 (.05 mm). 2. Unless otherwise specified, front face of pin insert pattern is shown.

15、Socket inserts are the reverse. 3. -12-Cable IPCEA 4-NO 2 conductor round type G, 0 - 600 volts. 4. -13-Cable-C0-04-HDF (4/1-4/8R) 1620 in accordance with MIL-DTL-3432. 5. Mark 44-12 on 44-13 insert. Trademark and 44-( ) shall appear in available space. Contact identifying letter shall be located so

16、 as to identify relative contact. 6. Only the pin contact is lengthened and has the N (neutral) designation. The mating socket contact is the same as the power contact. 7. The contact position labeled (G) in the insert arrangement contains the 1/0N (neutral) size pin contact that is connected to the

17、 shell to form a grounding pin contact. FIGURE 4. AC three phase four wire grounding, -12 and -13 insert arrangements, service D. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS14055J 5Quantity Contact Size Socket SAE-AS39029/49-Pin SAE-AS39029/48

18、-3 A, B, C 1/0 333 323 1 G 1/0N 333 (see note 9) 324 NOTES: 1. Dimensions are in inches. Metric equivalents given for information only. Unless otherwise specified, tolerance is .002 (.05 mm). 2. Unless otherwise specified, front face of pin insert pattern is shown. Socket inserts are the reverse. 3.

19、 -50-four each NO 1 wire (receptacles only). 4. -51-Cable-IPCEA 4-NO 1 conductor round type W, 0 - 600 volts, 1.68 inch OD. 5. -52-Cable-IPCEA 4-NO 2 conductor round type W, 0 - 600 volts, 1.48 inch OD. 6. -56-Cable-IPCEA 4-NO 6 conductor round type W, 0 - 600 volts, 1.10 inch OD. 7. For Navy ground

20、 support equipment use only. 8. Mark 44-50 on 44-51 insert, 44-52 on 44-56 insert. Trademark and 44-( ) shall appear in available space. Contact identifying letter shall be located so as to identify relative contact. 9. Only the pin contact is lengthened and has the N (neutral) designation. The mati

21、ng socket contact is the same as the power contact. 10. The contact position labeled (G) in the insert arrangement contains the 1/0N (neutral) size pin contact that is connected to the shell to form a grounding pin contact. FIGURE 5. AC three phase three wire grounding, -50, -51, -52 and -56 insert

22、arrangements, service D. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS14055J 6Insert rotation (degrees from normal) Alternate (see figures 7 through 10) 400 Hz Arrangement number Normal DC or 60 Hz (see figures 7 through 10) Z X Y 44 02 44 03 0

23、- - - 44 04 44 05 0 45 - - 44 06 0 - - - 44 12 44 13 0 60 - - 44 50 44 51 0 - - - 44 52 44 56 0 - - - FIGURE 6. Insert arrangements and rotations. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS14055J 7NOTES: 1. For use with connectors under MS905

24、55 and MS90557 utilizing socket contacts and normal keying. 2. Front face of socket insert shown. FIGURE 7. Socket contact pattern and polarization, insert in normal position (60 Hz power only). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS14055

25、J 8NOTES: 1. For use with connectors under MS90555 and MS90557 utilizing socket contacts and alternate (Z) keying. 2. Front face of socket insert shown. FIGURE 8. Socket contact pattern and polarization, insert in alternate position (400 Hz power only). Provided by IHSNot for ResaleNo reproduction o

26、r networking permitted without license from IHS-,-,-MS14055J 9NOTES: 1. For use with connectors under MS90556 and MS90558 utilizing pin contacts and normal keying. 2. Front face of pin insert shown. FIGURE 9. Socket contact pattern and polarization, insert in normal position (60 Hz power only). Prov

27、ided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS14055J 10NOTES: r use with connectors under MS90556 and MS90558 utilizing pin contacts . own. FIGURE 10. Socket contact pattern and polarization, insert in alternate position (400 Hz power only)1. Foand a

28、lternate (Z) keying. 2 Front face of pin insert sh. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS14055J 11EQUIREMENTS: Design and construction, see figures 1 through 10 and table I. eutral pin (N) is not connected to shell. rounding pin (G) is c

29、onnected to shell. pplicable SAE-AS33481 crimp bushings shall be supplied with the contacts for insert arrangements TABLE I. AccessoriesRNGAas specified. . Contacts Cable conductors MS90556 & MS90557 Contact bushings required Ins rt arrangement Quantity Size QTY PIN SAE- AS33481- eQuantity Size 44 0

30、2 2 1/0 2 2 2 1-2L 44 04 2 2 1/0 4 2 2 2 6(G) 2 2 1-2L 4-6L 44 05 1/0 5(G) 4-5L 2 2 4 2 2 2 - 2 - 44 06 1/0 8(G) 3 3 6 3 3 2 3 3 1-2L 6-8L 44 12 1/0 9(G) 4 4 6 4 4 2 4 4 1-2L 6-9L 44 13 1/0 8(G) 6-8L 4 4 6 4 4 1 - 4 - 44 52 1/0 4 4 2 4 1-2L 44 56 4 1/0 4 6 4 1-6L hanges from previous issue. Marginal

31、 notations are not used in this revision to identify changes with eferenced documents. In addition to MIL-DTL-22992, this document references the following: IL-DTL-3432 481 Crespect to the previous issue due to the extent of the changes. RMMS90555 MS90556 MS90557 MS90558 SAE-AS33Provided by IHSNot f

32、or ResaleNo reproduction or networking permitted without license from IHS-,-,-MS14055J 12CONCLUDING MATERIAL Custodians: Preparing activity: 5 e ew activities: roject 59352008-153) CR4 I Y OTE: The activities listed above were interested in this document as of the date of this document. Army CR DLA

33、CC Navy EC Air Force 8DLA CC R vi (PArmy AT, AV, , M Navy AS, CG, MC, OS, D Air Force 19 NSince organizations and responsibilities can change, you should verify the currency of the informationabove using the ASSIST Online database at http:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-