DLA MS14056 REV B-2009 CONTACTS ELECTRICAL CONNECTOR SHIELDED CABLE APPLICATIONS SIZE 8.pdf

1、INCH-POUNDMS14056B 1 April 2009 SUPERSEDING MS14056A 3 January 2003 DETAIL SPECIFICATION SHEET CONTACTS, ELECTRICAL CONNECTOR, SHIELDED CABLE APPLICATIONS, SIZE 8 This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the p

2、roduct described herein shall consist of this specification sheet and MIL-DTL-22992. FIGURE 1. Pin. AMSC N/A FSC 5935 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS14056B 2 NOTES: 1. All dimensions are in inches and are after plating. 2. Metric e

3、quivalents (to the nearest .01 mm) are given for general information only and are based upon 1 inch = 25.4 mm. 3. Surface roughness to be 63 or better in accordance with ASME-B46. 1 unless otherwise specified. 4. Remove all burrs and sharp edges .003-.005 (.08 -.13 mm) R unless otherwise specified.

4、5. All diameters to be concentric to each other within .005 (.13mm) total indicator reading (TIR), unless otherwise specified. 6. Outer contacts (shields) shall be crimped with a tool conforming to MIL-C-22520/5 with appropriate dies (see figure 3). The inner pin and socket contacts shall be either

5、crimped with a MIL-C-22520/2 crimp tool or soldered in accordance with manufacturers instructions. 7. Point at which a square ended .218 (5.54 mm) dia pin first engages the outer socket contact spring. 8. Point at which a square ended .0355 (.90 mm) dia pin first engages the inner socket contact spr

6、ing. 9. Materials: Outer socket contact, inner socket contact beryllium copper in accordance with ASTM-B196/B196M, ASTM-B197/B197M, and ASTM-B194. Outer pin contact, retaining ferrule, retaining nut brass in accordance with ASTM-B121/B121M, ASTM-B36/B36M, ASTM-B16/B16M and ASTM-B124/B124M. Inner pin

7、 contact brass in accordance with ASTM-B159/B159M and ASTM-B206/B206M. Insulators polyetrafluoroethylene (TFE) or fluorinated ethylene propylene (FEP) resin. 10. Engaging and separation forces test pins to be in accordance with SAE-AS31971 except for the diameters listed below: A. Outer socket conta

8、ct 48 oz max engaging force with .2192/.2190 (5.568/5.563 mm) dia pin 4 oz min separation force with a .2170/.2168 (5.512/5.507 mm) dia pin. B. Inner socket contact 18 oz max engaging force with .0367/.-0365 (.932/.927 mm) dia pin. 3/4 oz min separation force with a .0345/.0343 ( .876/.871 mm) dia p

9、in. 11. Dielectric withstanding voltage 1500 vac rms, applied between inner and outer contacts. 12. Insulation resistance measured between inner and outer contacts. 13. Probe damage not applicable. 14. Crimp tensile strength: Tensile strength (lbs. min) Dash no. Inner contact Outer contact -1 4 18 -

10、2 20 60 15. Contact retention: A. Outer contact. 20 pounds. B. Inner contact: 5 pounds. 16. Contact resistance: A. Outer contact: 5 mv at 1 amp. B. Inner contact: 15 mv at 1 amp. FIGURE 1. Pin Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-

11、,-MS14056B FIGURE 2. Socket. 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS14056B 4 nearest .01 mm) are given for general information only and are based ghness to be 63 or better in accordance with ASME-B46. 1 unless otherwise ic to each other

12、within .005 (.13mm) total indicator reading (TIR), ed with a which a square ended .218 (5.54 mm) dia pin first engages the outer socket contact which a square ended .0355 (.90 mm) dia pin first engages the inner socket contact 9. copper in accordance with ASTM-rdance with ASTM-B121/B121M, ss in acco

13、rdance with ASTM-B159/B159M and forces test pins to be in accordance with SAE-AS31971 except for the mm) m) r and outer contacts. between inner and outer contacts. licable. 4. Crimp tensile strength: Tensile strength (lbs. min) NOTES: 1. All dimensions are in inches and are after plating. 2. Metric

14、equivalents (to theupon 1 inch = 25.4 mm. 3. Surface rouspecified. 4. Remove all burrs and sharp edges .003-.005 (.08 -.13 mm) R unless otherwise specified. 5. All diameters to be concentrunless otherwise specified. 6. Outer contacts (shields) shall be crimped with a tool conforming to MIL-C-22520/5

15、 with appropriate dies (see figure 3). The inner pin and socket contacts shall be either crimpMIL-C-22520/2 crimp tool or soldered in accordance with manufacturers instructions. 7. Point at spring. 8. Point at spring. Materials: Outer socket contact, inner socket contact beryllium B196/B196M, ASTM-B

16、197/B197M, and ASTM-B194. Outer pin contact, retaining ferrule, retaining nut brass in accoASTM-B36/B36M, ASTM-B16/B16M and ASTM-B124/B124M. Inner pin contact braASTM-B206/B206M. Insulators polyetrafluoroethylene (TFE) or fluorinated ethylene propylene (FEP) resin. 10. Engaging and separationdiamete

17、rs listed below: a. Outer socket contact 48 oz max engaging force with .2192/.2190 (5.568/5.563dia pin 4 oz min separation force with a .2170/.2168 (5.512/5.507 mm) dia pin. B. Inner socket contact 18 oz max engaging force with .0367/.-0365 (.932/.927 mdia pin. 3/4 oz min separation force with a .03

18、45/.0343 ( .876/.871 mm) dia pin. 11. Dielectric withstanding voltage 1500 vac rms, applied between inne12. Insulation resistance measured13. Probe damage not app1Dash contact contact no. Inner Outer -1 4 18 -2 20 60 15. Contact retention: a. Outer contact. 20 pounds. t: 5 pounds. b. Inner contact:

19、15 mv at 1 amp. FIGURE 2. Socketb. Inner contac16. Contact resistance: a. Outer contact: 5 mv at 1 amp. Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS14056B 5 FIGURE 3. General dimensionsDash NO. Coaxial cable A dia min B dia C dia min

20、 Crimp Ferrule Hex crimp dies (see note 6) -1 M17/94-RG179 .067 .110 .106 .014 MS21980-128 MS21981-058 M22520/5-35 -2 M17/184-00001 M17/185-00001 M17/97-RG210 .152 .185 .181 .027 MS21980-225 MS21981-134 M22520/5-45 D E DASH NO. -D D -D -DMIL TL-5015 MIL- TL-22992 MIL TL-5015 MIL TL-22992 -1 Plug Rec

21、eptacle Plug Receptacle Plug Receptacle Plug Receptacle -2 .204 .207 .204 .254 .174 .177 .174 .224 .269 .267 .269 .314 .240 .237 .240 .284 . Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS14056B 6 FIGURE 3. General dimensions Continued. Inches mm

22、Inches Inches mm Inches mm mm .007 .18 .074 1.88 .240 6.10 .731 19.08 .010 .25 .080 2.03 .242 6.15 .766 19.46 .011 .28 .106 2.69 .250 6.35 1.547 39.29 .013 .33 .110 2.79 .254 6.45 1.578 40.08 .014 .36 .117 2.97 .260 6.60 .019 .48 .122 3.10 .264 6.71 .020 .51 .152 3.86 .267 6.78 .022 .56 .155 3.94 .2

23、69 6.83 .027 .69 .174 4.42 .276 7.01 .034 .88 .177 4.50 .281 7.14 .036 .93 .179 4.55 .284 7.21 .038 .97 .181 4.60 .310 7.87 .041 1.04 .185 4.70 .314 7.98 .049 1.24 .207 5.26 .316 8.03 .051 1.30 .217 5.51 .325 8.26 .062 1.57 .219 5.56 .359 9.12 .065 1.65 .224 5.69 .379 9.63 .066 1.68 .234 5.94 .719 1

24、8.26 .067 1.70 .237 6.02 .730 18.54 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS14056B 7 in this revision to identify changes with spect to the previous issue due to the extent of the changes. eferenced documents. In addition to MIL-DTL-22992,

25、this document references the following: 197M 06M AE-AS31971 Changes from previous issue. Marginal notations are not used reRMIL-C-22520/2 MIL-C-22520/5 MIL-DTL-5015 ASME-B46.1 ASTM-B196/B196M ASTM-B197/BASTM-B194 ASTM-B121/B121MASTM-B36/B36M ASTM-B16/B16M ASTM-B124/B124M ASTM-B159/B159M ASTM-B206/B2

26、SProvided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS14056B 8 CONCLUDING MATERIAL vity: DLA CC LA CC ies: (Project 59352008-154) , OS, SH Air Force 19 the currency of the information bove using the ASSIST Online database at http:/assist.daps.dla.milCus

27、todians: Preparing actiArmy CR Navy EC Air Force 85D Review activitArmy MI Navy AS, CGNOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify a . Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-