DLA MS14308 REV C-2009 ELBOWS PIPE BRASS OR BRONZE THREADED 90-DEG REDUCING CLASS 125.pdf

1、ZXDETAIL SPECIFICATION SHEET ELBOWS, PIPE, BRASS OR BRONZE, THREADED, 90-DEG., REDUCING, CLASS 125 This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification shee

2、t and WW-P-460. 90 ELBOW, REDUCING FIGURE 1. Reducing elbow fitting. AMSC N/A FSC 4730 INCH-POUND MS14308C 15 December 2009 SUPERSEDING MS14308B 28 February 1994 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS14308C 2 Dash number to pipe size. Das

3、h number Pipe size mm - 1 - 2 - 3 - 4 - 5 - 6 - 7 - 8 - 9 - 10 - 11 - 12 - 13 - 14 1/4 X 1/8 (.250 X .125) 3/ 8 X 1/4 (.375 X .250) 1/2 X 3/8 (.500 X 375) 3/4 X 1/2 (.750 X .500) 1 X 3/4 (1.000 X .750) 1 X 1/2 (1.000 X .500) 1-1/4 X 1 (1.250 X 1.000) 1-1/4 X 3/4 (1.250 X .750) 1-1/2 X 1-1/4 (1.500 X

4、 1.250) 1-1/2 X 1 (1.500 X 1.000) 2 X 1-1/2 (2.000 X 1.500) 2-1/2 X 2 (2.500 X 2.000) 3 X 2-1/2 (3.000 X 2.500) 4 X 3 (4.000 X 3.000) 6.35 X 3.18 9.53 X 6.35 12.70 X 9.53 19.05 X 12.70 25.40 X 19.05 25.40 X 12.70 31.75 X 25.40 31.75 X 19.05 38.10 X 31.75 38.10 X 25.40 50.80 X 38.10 63.50 X 50.80 76.

5、20 X 63.50 101.60 X 76.20 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for information only. 3. Material: Brass or bronze in accordance with ASME-B16.15. 4. Protective Coating: None 5. Dimensions: In accordance with ASME-B16.15, table titled “Dimensions of 90-deg Elbows (Reduc

6、ing Sizes) Class 125”. 6. Thread: As specified in ASME-B16.15. 7. Marking: In accordance with ASME-B16.15. 8. Part or Identifying Number (PIN): The MS PIN consists of the MS number, the dash number, and the fitting Identification letter(s). When left-hand threads are required, add the letter “L” to

7、the PIN. FIGURE 1. Reducing elbow fitting Continued. PIN: MS 14308 -3 X L Examples: MS14308 - 4 represents a 3/4 NPS X 1/2 NPS 90 reducing elbow. MS14308 - 7L represents a 1-1/4 NPS X 1 NPS reducing elbow left-hand threads. MS prefix Basic specification number Dash number on figure 1 Outside head, i

8、nside head, face designator, see figure 1 Thread designator: Blank right hand thread, L- left hand thread Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS14308C 3 Changes from previous issue. Marginal notations are not used in this revision to iden

9、tify changes with respect to the previous issue, due to the extent of the changes. Referenced documents. In addition to WW-P-460, this document references the following: ASME-B16.15 CONCLUDING MATERIAL Custodians: Preparing activity: Army - AT DLA - CC Navy - MC Air Force - 99 DLA - CC (Project 4730

10、-2009-006) Review activities: Army - AR, CE, EA Navy SA, SH, YD Air Force - 71 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-