DLA MS3185 REV B-2013 MOLD POTTING AND ADAPTER ELECTRICAL CONNECTOR (FOR MIL-DTL-26482 SERIES 1 CLASS P).pdf

1、 MS3185B 12 September 2013 SUPERSEDING MS3185A 15 February 1967 DETAIL SPECIFICATION SHEET MOLD, POTTING, AND ADAPTER, ELECTRICAL CONNECTOR (FOR MIL-DTL-26482, SERIES 1, CLASS P) This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for

2、 acquiring the product described herein shall consist of this specification sheet and MIL-DTL-26482. NOTES: 1. Dimensions are in inches. Metric equivalents are given for information only. 2. Thread relief must be larger than one full thread to allow potting compound to fill thread relief when boot i

3、s bottomed on mating connector accessory thread. 3. When a separate metal threaded ring is provided, ring shall be .125 minimum thickness having an interference fit with the boot. The separate metal ring shall be mandatory on the 75-90 degree elbow. FIGURE 1. Mold, potting, straight boot. AMSC N/A F

4、SC 5935 Inactive for new design after 12 September 2013. INCH-POUND Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS3185B 2 Straight mold Size Part number V V class 2B thread C min perf thd L max X dia min ID Y dia max OD Z dia min ID 8 MS3185-8-1

5、7/16-28 .199 .825 .317 .608 .386 10 MS3185-10-1 9/16-24 .433 .734 .503 12 MS3185-12-1 11/16-24 .548 .858 .628 14 MS3185-14-1 13/16-20 .673 .984 .733 16 MS3185-16-1 15/16-20 .798 1.110 .868 18 MS3185-18-1 1-1/16-18 .899 1.234 .985 20 MS3185-20-1 1-3/16-18 .287 .915 1.024 1.360 1.110 22 MS3185-22-1 1-

6、5/16-18 1.149 1.484 1.235 24 MS3185-24-1 1-7/16-18 .199 1.274 1.610 1.362 Inches mm Inches mm Inches mm Inches mm .199 5.06 .608 15.44 .868 22.05 1.250 31.75 .287 7.29 .628 15.95 .899 22.83 1.274 32.36 .317 8.05 .673 17.09 .915 23.24 1.360 34.54 .386 9.80 .733 18.62 .984 24.99 1.362 34.59 .433 11.00

7、 .734 18.64 .985 25.02 1.484 37.69 .503 12.78 .798 20.27 1.024 26.01 1.610 40.89 .548 13.91 .858 21.79 1.235 31.37 FIGURE 1. Mold, potting, straight boot Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS3185B 3 NOTES: 1. Dimensions are in

8、 inches. Metric equivalents are given for information only. 2. Thread relief must be larger than one full thread to allow potting compound to fill thread relief when boot is bottomed on mating connector accessory thread. 3. When separate metal threaded ring is provided, ring shall be .125 minimum th

9、ick having an interference fit with the boot. The separate metal ring shall be mandatory on the 75-90 degree elbow. 4. Entrance configuration optional with indicated cross-sectional area. Elbow mold Size Part number V V class 2B thread A min cross-sec area ( in2 ) B max C min perf thd L 75-90 deg ma

10、x X dia min ID Y dia max OD Z dia min ID 8 MS3185-8-2 7/16-28 .078 1.030 .199 1.125 .317 .608 .386 10 MS3185-10-2 9/16-24 .147 1.125 1.250 .433 .734 .503 12 MS3185-12-2 11/16-24 .190 1.250 1.344 .548 .858 .628 14 MS3185-14-2 13/16-20 .226 1.297 1.453 .673 .984 .733 16 MS3185-16-2 15/16-20 .304 1.375

11、 1.516 .798 1.110 .868 18 MS3185-18-2 1-1/16-18 .532 1.469 1.594 .899 1.234 .985 20 MS3185-20-2 1-3/16-18 .619 1.700 .287 1.750 1.024 1.360 1.110 22 MS3185-22-2 1-5/16-18 .690 1.703 1.828 1.149 1.484 1.235 24 MS3185-24-2 1-7/16-18 .806 2.100 .199 2.125 1.274 1.610 1.362 FIGURE 2. Mold, potting, elbo

12、w, 75-90 degrees. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS3185B 4 Inches mm Inches mm Inches mm Inches mm .078 1.98 .733 18.62 1.235 31.37 1.610 40.89 .147 3.73 .734 18.64 1.250 31.75 1.700 43.18 .190 4.83 .798 20.27 1.274 32.36 1.703 43.26

13、 .226 5.74 .806 20.47 1.297 32.94 1.750 44.45 .304 7.72 .858 21.79 1.344 34.14 1.828 46.43 .317 8.05 .868 22.05 1.360 34.54 2.100 53.34 .386 9.80 .899 22.83 1.362 34.59 2.125 53.98 .433 11.00 .984 24.99 1.370 34.80 .532 13.51 .985 25.02 1.453 36.91 .548 13.91 1.024 26.01 1.469 37.31 .608 15.44 1.030

14、 26.16 1.484 37.69 .619 15.72 1.110 28.19 1.516 38.51 .690 17.53 1.125 28.56 1.594 40.49 FIGURE 2. Mold, potting, elbow, 75-90 degrees Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS3185B 5 REQUIREMENTS: Dimensions and configurations: S

15、ee figures 1 and 2. Use: This potting form is used with MIL-DTL-26482, class P connectors. Materials: Boot body or plastic parts Translucent nylon. Metal threaded ring - Aluminum. Minimum plastic wall thickness: .020 inches. Intermateability dimensions are in accordance with MIL-DTL-26482. Part or I

16、dentifying Number (PIN) example: MS3185 - 10 - 1 MS number Size Boot geometry - 1 (straight) - 2 (75-90 degree elbow) Changes from previous issue. Marginal notations are not used in this revision to identify changes with respect to the previous issue due to the extent of the changes. Referenced docu

17、ments. This document references MIL-DTL-26482. CONCLUDING MATERIAL Custodians: Preparing activity: Army - CR DLA - CC Navy - AS Air Force - 85 (Project 5935-2012-226) DLA CC Review Activity: Air Force - 99 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-