DLA MS8005 REV D (1)-2005 HOSE ASSEMBLY POLYTETRAFLUOROETHYLENE PERMANENTLY ATTACHED FITTINGS HIGH TEMPERATURE MEDIUM PRESSURE FLARE-TO-FLARE《耀斑对耀斑中压高温可重复使用永久配件聚四氟乙烯软管组件》.pdf

1、 MS8005D w/AMENDMENT 1 09 September 2005 SUPERSEDING MS8005D 24 September 2003 DETAIL SPECIFICATION SHEET HOSE ASSEMBLY, POLYTETRAFLUOROETHYLENE, PERMANENTLY ATTACHED FITTINGS, HIGH TEMPERATURE, MEDIUM PRESSURE, FLARE-TO-FLARE This specification is approved for use by all Departments and Agencies of

2、 the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-25579. Hose assembly dimensions for style A: See table l. TABLE I. Hose assembly dimensions for style A. 1/ 1/ Style A uses class 1 fittings which are made fr

3、om corrosion resistant steel (CRES). Fitting ends Dimensions 2/ 1 2 Hose size A (nom) B ( max) C (max) F (max) 3/4 0.372 1.049 0.620 0.580 4 0.375 1.049 0.620 0.6545 0.380 1.194 0.680 0.726 6 0.380 1.303 0.750 0.798Straight Straight 8 0.438 1.465 0.880 1.014 10 0.515 1.680 0.967 1.15812 0.570 1.727

4、1.122 1.447 16Z 0.620 2.101 1.480 1.73620Z 0.640 2.255 1.750 2.328 24Z 0.765 2.400 2.150 2.621INCH-POUND2/ Dimensions are shown on figure 1. FIGURE 1. Style A hose assembly. AMSC N/A FSC 4720 Source: http:/assist.daps.dla.mil - Downloaded: 2005-09-30T07:33ZCheck the source to verify that this is the

5、 current version before use.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS8005D w/AMENDMENT 1 2 Hose assembly dimensions for style B: See table II. TABLE II. Hose assembly dimensions for style B. 1/ 1/ Style B uses class 1 fittings which are made

6、 from CRES. 2/ Dimensions are shown on figure 2. FIGURE 2. Style B hose assembly. Hose assembly dimensions for style C: See table III. TABLE III. Hose assembly dimensions for style C. 1/ 1/ Style C uses class 1 fittings which are made from CRES. Fitting ends Dimensions 2/ 1 2 Hose size A (nom) B (ma

7、x) C (max) D (max) E (max) F (max) G (min) G (max)3/4 0.372 1.049 0.620 1.240 0.921 0.580 0.263 0.388 4 0.375 1.049 0.620 1.490 0.979 0.654 0.302 0.427 5 0.380 1.194 0.680 1.495 1.009 0.726 0.320 0.445 6 0.380 1.303 0.750 1.610 1.079 0.798 0.369 0.494 Straight 45 8 0.438 1.465 0.880 1.722 1.332 1.01

8、4 0.445 0.632 10 0.515 1.680 0.967 2.037 1.488 1.158 0.501 0.688 12 0.570 1.727 1.122 2.368 1.667 1.447 0.588 0.775 16Z 0.620 2.101 1.480 2.583 1.879 1.736 0.609 0.857 20Z 0.640 2.255 1.750 2.946 2.058 2.328 0.697 1.017 24Z 0.765 2.400 2.150 3.210 2.400 2.621 0.785 1.127 Fitting ends Dimensions 2/ 1

9、 2 Hose size A (nom) B (max) C (max) F (max) H (max) J (max) K (min) K (max)3/4 0.372 1.049 0.620 0.580 1.845 1.320 0.510 0.635 4 0.375 1.049 0.620 0.654 1.885 1.370 0.560 0.685 5 0.380 1.194 0.680 0.726 1.980 1.542 0.635 0.822 6 0.380 1.303 0.750 0.798 2.205 1.640 0.700 0.885 Straight 90 8 0.438 1.

10、465 0.880 1.014 2.495 1.938 0.810 1.060 10 0.515 1.680 0.967 1.158 2.955 2.340 1.091 1.341 12 0.570 1.727 1.122 1.447 3.705 2.722 1.341 1.591 16Z 0.620 2.101 1.480 1.736 4.100 3.075 1.465 1.715 20Z 0.640 2.255 1.750 2.328 4.835 3.637 1.747 2.122 24Z 0.765 2.400 2.150 2.621 5.480 4.212 1.997 2.372 2/

11、 Dimensions are shown on figure 3. Source: http:/assist.daps.dla.mil - Downloaded: 2005-09-30T07:33ZCheck the source to verify that this is the current version before use.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS8005D w/AMENDMENT 1 3 FIGURE

12、3. Style C hose assembly. Hose assembly dimensions for style D: See table IV. TABLE IV. Hose assembly dimensions for style D. 1/ 1/ Style D uses class 1 fittings which are made from CRES. Fitting ends Dimensions 2/ 1 2 Hose size A (nom) C (max) D (max) E (max) F (max) G (min) G (max) 3/4 0.372 0.620

13、 1.240 0.921 0.580 0.263 0.388 4 0.375 0.620 1.490 0.979 0.654 0.302 0.427 5 0.380 0.680 1.495 1.009 0.726 0.320 0.445 6 0.380 0.750 1.610 1.079 0.798 0.369 0.494 45 45 8 0.438 0.880 1.722 1.332 1.014 0.445 0.632 10 0.515 0.967 2.037 1.488 1.158 0.501 0.688 12 0.570 1.122 2.368 1.667 1.447 0.588 0.7

14、75 16Z 0.620 1.480 2.583 1.879 1.736 0.609 0.857 20Z 0.640 1.750 2.946 2.058 2.328 0.697 1.017 24Z 0.765 2.150 3.210 2.400 2.621 0.785 1.127 2/ Dimensions are shown on figure 4. FIGURE 4. Style D hose assembly. Source: http:/assist.daps.dla.mil - Downloaded: 2005-09-30T07:33ZCheck the source to veri

15、fy that this is the current version before use.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS8005D w/AMENDMENT 1 4 Hose assembly dimensions for style E: See table V. TABLE V. Hose assembly dimensions for style E. 1/ 1/ Style E uses class 1 fittin

16、gs which are made from CRES. 2/ Dimensions are shown on figure 5. FIGURE 5. Style E hose assembly. Hose assembly dimensions for style F: See table VI. TABLE VI. Hose assembly dimensions for style F. 1/ 1/ Style F uses class 1 fittings which are made from CRES. Dimensions 2/ Fitting ends 1 2 Hose siz

17、e A (nom) C (max) D (max)E (max)F (max)G (min) G (max)H (max) J (max) K (min) K (max)3/4 0.372 0.620 1.240 0.921 0.580 0.263 0.388 1.845 1.320 0.510 0.6354 0.375 0.620 1.490 0.979 0.654 0.302 0.427 1.885 1.370 0.560 0.6855 0.380 0.680 1.495 1.009 0.726 0.320 0.445 1.980 1.542 0.635 0.8226 0.380 0.75

18、0 1.610 1.079 0.798 0.369 0.494 2.205 1.640 0.700 0.88545 90 8 0.438 0.880 1.722 1.332 1.014 0.445 0.632 2.495 1.938 0.810 1.06010 0.515 0.967 2.037 1.488 1.158 0.501 0.688 2.955 2.340 1.091 1.34112 0.570 1.122 2.368 1.667 1.447 0.588 0.775 3.705 2.722 1.341 1.59116Z 0.620 1.480 2.583 1.879 1.736 0.

19、609 0.857 4.100 3.075 1.465 1.71520Z 0.640 1.750 2.946 2.058 2.328 0.697 1.017 4.835 3.637 1.747 2.12224Z 0.765 2.150 3.210 2.400 2.621 0.785 1.127 5.480 4.212 1.997 2.372Fitting ends Dimensions 2/ 1 2 Hose size A (nom) C (max) F (max) H (max) J (max) K (min) K (max) 3/4 0.372 0.620 0.580 1.845 1.32

20、0 0.510 0.635 4 0.375 0.620 0.654 1.885 1.370 0.560 0.685 5 0.380 0.680 0.726 1.980 1.542 0.635 0.822 6 0.380 0.750 0.798 2.205 1.640 0.700 0.885 90 90 8 0.438 0.880 1.014 2.495 1.938 0.810 1.060 10 0.515 0.967 1.158 2.955 2.340 1.091 1.341 12 0.570 1.122 1.447 3.705 2.722 1.341 1.591 16Z 0.620 1.48

21、0 1.736 4.100 3.075 1.465 1.715 20Z 0.640 1.750 2.328 4.835 3.637 1.747 2.122 24Z 0.765 2.150 2.621 5.480 4.212 1.997 2.372 2/ Dimensions are shown on figure 6. Source: http:/assist.daps.dla.mil - Downloaded: 2005-09-30T07:33ZCheck the source to verify that this is the current version before use.Pro

22、vided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS8005D w/AMENDMENT 1 5 FIGURE 6. Style F hose assembly. Hose assembly dimensions for style G: See table VII. TABLE VII. Hose assembly dimensions for style G. 1/ 1/ Style G uses class 2 fittings which are

23、made from a combination of aluminum and CRES. Fitting ends Dimensions 2/ 1 2 Hose size A (nom) B ( max) C (max) F (max) 8 0.438 1.465 0.880 1.014 10 0.515 1.680 0.967 1.158Straight Straight 12 0.570 1.727 1.122 1.447 16Z 0.620 2.101 1.480 1.73620Z 0.640 2.255 1.750 2.328 24Z 0.765 2.400 2.150 2.6212

24、/ Dimensions are shown on figure 7. FIGURE 7. Style G hose assembly. Source: http:/assist.daps.dla.mil - Downloaded: 2005-09-30T07:33ZCheck the source to verify that this is the current version before use.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,

25、-,-MS8005D w/AMENDMENT 1 6 Hose assembly dimensions for style H: See table VIII. TABLE VIII. Hose assembly dimensions for style H. 1/ 1/ Style H uses class 2 fittings which are made from a combination of aluminum and CRES. 2/ Dimensions are shown on figure 8. FIGURE 8. Style H hose assembly. Hose as

26、sembly dimensions for style J: See table IX. TABLE IX. Hose assembly dimensions for style J. 1/ 1/ Style J uses class 2 fittings which are made from a combination of aluminum and CRES. Fitting ends Dimensions 2/ 1 2 Hose size A (nom) B (max) C (max) D (max) E (max) F (max) G (min) G (max)8 0.438 1.4

27、65 0.880 1.722 1.332 1.014 0.445 0.632 10 0.515 1.680 0.967 2.037 1.488 1.158 0.501 0.688 Straight 45 12 0.570 1.727 1.122 2.368 1.667 1.447 0.588 0.775 16Z 0.620 2.101 1.480 2.583 1.879 1.736 0.609 0.857 20Z 0.640 2.255 1.750 2.946 2.058 2.328 0.697 1.017 24Z 0.765 2.400 2.150 3.210 2.400 2.621 0.7

28、85 1.127 Fitting ends Dimensions 2/ 1 2 Hose size A (nom) B (max) C (max) F (max) H (max) J (max) K (min) K (max)8 0.438 1.465 0.880 1.014 2.495 1.938 0.810 1.060 10 0.515 1.680 0.967 1.158 2.955 2.340 1.091 1.341 Straight 90 12 0.570 1.727 1.122 1.447 3.705 2.722 1.341 1.591 16Z 0.620 2.101 1.480 1

29、.736 4.100 3.075 1.465 1.715 20Z 0.640 2.255 1.750 2.328 4.835 3.637 1.747 2.122 24Z 0.765 2.400 2.150 2.621 5.480 4.212 1.997 2.372 2/ Dimensions are shown on figure 9. Source: http:/assist.daps.dla.mil - Downloaded: 2005-09-30T07:33ZCheck the source to verify that this is the current version befor

30、e use.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS8005D w/AMENDMENT 1 7 FIGURE 9. Style J hose assembly. Hose assembly dimensions for style K: See table X. TABLE X. Hose assembly dimensions for style K. 1/ 1/ Style K uses class 2 fittings which

31、 are made from a combination of aluminum and CRES. Fitting ends Dimensions 2/ 1 2 Hose size A (nom) C (max) D (max) E (max) F (max) G (min) G (max) 8 0.438 0.880 1.722 1.332 1.014 0.445 0.632 10 0.515 0.967 2.037 1.488 1.158 0.501 0.688 45 45 12 0.570 1.122 2.368 1.667 1.447 0.588 0.775 16Z 0.620 1.

32、480 2.583 1.879 1.736 0.609 0.857 20Z 0.640 1.750 2.946 2.058 2.328 0.697 1.017 24Z 0.765 2.150 3.210 2.400 2.621 0.785 1.127 2/ Dimensions are shown on figure 10. FIGURE 10. Style K hose assembly. Source: http:/assist.daps.dla.mil - Downloaded: 2005-09-30T07:33ZCheck the source to verify that this

33、is the current version before use.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS8005D w/AMENDMENT 1 8 Hose assembly dimensions for style M: See table XI. TABLE XI. Hose assembly dimensions for style M. 1/ 1/ Style M uses class 2 fittings which ar

34、e made from a combination of aluminum and CRES. 2/ Dimensions are shown on figure 11. FIGURE 11. Style M hose assembly. Hose assembly dimensions for style N: See table XII. TABLE XII. Hose assembly dimensions for style N. 1/ 1/ Style N uses class 2 fittings which are made from a combination of alumi

35、num and CRES. Dimensions 2/ Fitting ends 1 2 Hose size A (nom)C (max) D (max)E (max)F (max)G (min) G (max)H (max) J (max) K (min)K (max)8 0.438 0.880 1.722 1.332 1.014 0.445 0.632 2.495 1.938 0.810 1.06010 0.515 0.967 2.037 1.488 1.158 0.501 0.688 2.955 2.340 1.091 1.34145 90 12 0.570 1.122 2.368 1.

36、667 1.447 0.588 0.775 3.705 2.722 1.341 1.59116Z 0.620 1.480 2.583 1.879 1.736 0.609 0.857 4.100 3.075 1.465 1.71520Z 0.640 1.750 2.946 2.058 2.328 0.697 1.017 4.835 3.637 1.747 2.12224Z 0.765 2.150 3.210 2.400 2.621 0.785 1.127 5.480 4.212 1.997 2.372Fitting ends Dimensions 2/ 1 2 Hose size A (nom)

37、 C (max) F (max) H (max) J (max) K (min) K (max) 8 0.438 0.880 1.014 2.495 1.938 0.810 1.060 10 0.515 0.967 1.158 2.955 2.340 1.091 1.341 90 90 12 0.570 1.122 1.447 3.705 2.722 1.341 1.591 16Z 0.620 1.480 1.736 4.100 3.075 1.465 1.715 20Z 0.640 1.750 2.328 4.835 3.637 1.747 2.122 24Z 0.765 2.150 2.6

38、21 5.480 4.212 1.997 2.372 2/ Dimensions are shown on figure 12. Source: http:/assist.daps.dla.mil - Downloaded: 2005-09-30T07:33ZCheck the source to verify that this is the current version before use.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-M

39、S8005D w/AMENDMENT 1 9 FIGURE 12. Style N hose assembly. Protective sleeve code: See table XIII. TABLE XIII. Protective sleeve code. Code Type A SAE AS1072 sleeve, fire protection, silicone covered, temperature ranging from -65F to 450F and intermittently to 500F, secured with CRES bands as required

40、. 1/ B SAE AS1073 - code B sleeve, abrasion protection, heat shrinkable, black polyolefin, temperature ranging from -65F to 250F. C SAE AS1291 - code A sleeve, chafe guard, extruded seamless white PTFE, temperature ranging from -65F to 450F, secured with CRES bands as required. D SAE AS1291 - code C

41、 sleeve, chafe guard, extruded seamless transparent FEP, temperature ranging from -65F to 350F, secured with CRES bands as required. E SAE AS1298 sleeve, heavy wall chafe guard, extruded seamless black PTFE, temperature ranging from -65F to 450F, secured with CRES bands as required. L Lock-wire hole

42、 F Code A + L G Code B + L H Code C + L J Code D + L K Code E + L 1/ To prevent wicking of fluids, the cut end of the fire protective sleeve (code A) shall be coated with Room Temperature Vulcanized (RTV) silicone rubber prior to installation. After installation, cracks and voids in the fire protect

43、ive sleeve shall be coated with RTV rubber to prevent exposure of fiberglass. Source: http:/assist.daps.dla.mil - Downloaded: 2005-09-30T07:33ZCheck the source to verify that this is the current version before use.Provided by IHSNot for ResaleNo reproduction or networking permitted without license f

44、rom IHS-,-,-MS8005D w/AMENDMENT 1 10 Hose assembly size code: See table XIV. TABLE XIV. Hose assembly size code. Size Reference tube OD Size code 3/4 1/ B 4 0.250 E5 0.313 F6 0.375 G 8 0.500 H10 0.625 J12 0.750 K 16Z 1.000 M20Z 1.250 N24Z 1.500 P 1/ Size 3/4 hose assembly consists of a size 4 tube O

45、D hose assembled with size 3 tube OD fittings. REQUIREMENTS Dimensions: Unless otherwise specified, all dimensions are in inches. Dimensions “E (max)” and “J (max)” are installation dimensions and not design dimensions. Fittings: The swivel nut and cone seat shall mate with SAE AS4395 fitting. The s

46、wivel nut threads shall be in accordance with SAE AS8879. Assembly classification: Class 1 and class 2 hose assemblies, as specified in MIL-DTL-25579, have been incorporated into the Part or Identifying Number (PIN) as a part of styles. Angular alignment: Hose assemblies with elbow fittings on each

47、end shall have the angular orientation between the elbows measured counter-clockwise from the centerline of the nearest fitting, positioned at six-oclock, to the centerline of the other fitting (see figure 13). When applicable, the angular alignment shall be expressed in three digits and specified i

48、n the PIN. Protective sleeve: If required, the hose assembly shall include a protective sleeve (see table XIII) and its code shall be included in the PIN. Fire protective sleeve shall be subjected to testing in accordance with MIL-DTL-25579. Assembly length: Hose assembly shall be furnished in lengths as specified in the contract or purchase order (see MIL-DTL-25579); however, tolerances on the length of each hose assembly shall be as follows: a. 1/8 inch for lengths under 18 inches. b. 1/4 inch for lengths from 18 inches to 36 inches. c. 1/2 inch for lengths from 36 inches to 50