DLA MS8007 REV C (1)-2005 HOSE ASSEMBLY POLYTETRAFLUOROETHYLENE PERMANENTLY ATTACHED FITTINGS HIGH TEMPERATURE MEDIUM PRESSURE FLARE-TO-FLANGE《耀斑对耀斑中压高温可重复使用永久配件聚四氟乙烯软管组件》.pdf

1、 MS8007C w/AMENDMENT 1 09 September 2005 SUPERSEDING MS8007C 24 September 2003 DETAIL SPECIFICATION SHEET HOSE ASSEMBLY, POLYTETRAFLUOROETHYLENE, PERMANENTLY ATTACHED FITTINGS, HIGH TEMPERATURE, MEDIUM PRESSURE, FLARE-TO-FLANGE This specification is approved for use by all Departments and Agencies o

2、f the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-25579. Hose assembly dimensions for style A: See table l. TABLE I. Hose assembly dimensions for style A. 1/ 1/ Style A uses class 1 fittings which are made f

3、rom corrosion resistant steel (CRES). Fitting ends Dimensions 2/ 1 2 Hose size A (nom) B ( max) C (max) F (max) M (max) P (max) 8 0.438 1.465 0.880 1.014 1.560 0.875 10 0.515 1.680 0.967 1.158 1.570 1.000 Straight Straight 12 0.570 1.727 1.122 1.447 1.640 1.250 16Z 0.620 2.101 1.480 1.736 1.750 1.50

4、0 20Z 0.640 2.255 1.750 2.328 1.990 1.844 24Z 0.765 2.400 2.150 2.621 2.260 2.125 INCH-POUND2/ Dimensions are shown on figure 1. FIGURE 1. Style A hose assembly. AMSC N/A FSC 4720 Source: http:/assist.daps.dla.mil - Downloaded: 2005-09-30T07:35ZCheck the source to verify that this is the current ver

5、sion before use.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS8007C w/AMENDMENT 1 2 Hose assembly dimensions for style B: See table lI. TABLE II. Hose assembly dimensions for style B. 1/ 1/ Style B uses class 1 fittings which are made from CRES.

6、2/ Dimensions are shown on figure 2. FIGURE 2. Style B hose assembly. Hose assembly dimensions for style C: See table IIl. TABLE III. Hose assembly dimensions for style C. 1/ 1/ Style C uses class 1 fittings which are made from CRES. Fitting ends Dimensions 2/ 1 2 Hose size A (nom) B (max) C (max) D

7、 (max) F (max) N (max) P (max) R (min) R (max) 8 0.438 1.465 0.880 1.722 1.014 0.606 0.875 0.303 0.428 10 0.515 1.680 0.967 2.037 1.158 0.658 1.000 0.340 0.465 Straight 45 12 0.570 1.727 1.122 2.368 1.447 0.789 1.250 0.433 0.558 16Z 0.620 2.101 1.480 2.583 1.736 0.929 1.500 0.470 0.657 20Z 0.640 2.2

8、55 1.750 2.946 2.328 1.020 1.844 0.534 0.721 24Z 0.765 2.400 2.150 3.210 2.621 1.186 2.125 0.589 0.839 Fitting ends Dimensions 2/ 1 2 Hose size A (nom) B (max) C (max) F (max) P (max) S (max) T (max) U (min) U (max)8 0.438 1.465 0.880 1.014 0.875 2.320 1.422 0.857 0.982 10 0.515 1.680 0.967 1.158 1.

9、000 2.875 1.499 0.861 1.015 Straight 90 12 0.570 1.727 1.122 1.447 1.250 3.606 1.807 1.032 1.246 16Z 0.620 2.101 1.480 1.736 1.500 3.981 2.174 1.156 1.434 20Z 0.640 2.255 1.750 2.328 1.844 4.435 2.590 1.344 1.715 24Z 0.765 2.400 2.150 2.621 2.125 5.075 3.103 1.516 2.028 2/ Dimensions are shown on fi

10、gure 3. Source: http:/assist.daps.dla.mil - Downloaded: 2005-09-30T07:35ZCheck the source to verify that this is the current version before use.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS8007C w/AMENDMENT 1 3 FIGURE 3. Style C hose assembly. H

11、ose assembly dimensions for style D: See table lV. TABLE IV. Hose assembly dimensions for style D. 1/ Dimensions 2/ Fitting ends 1 2 Hose size A (nom) C (max) D (max) E (max)F (max) G (min) G (max) N (max) P (max)R (min) R (max) 8 0.438 0.880 1.722 1.332 1.014 0.445 0.632 0.606 0.875 0.303 0.428 10

12、0.515 0.967 2.037 1.488 1.158 0.501 0.688 0.658 1.000 0.340 0.465 45 45 12 0.570 1.122 2.368 1.667 1.447 0.564 0.775 0.789 1.250 0.433 0.558 16Z 0.620 1.480 2.583 1.879 1.736 0.609 0.857 0.929 1.500 0.470 0.657 20Z 0.640 1.750 2.946 2.058 2.328 0.697 1.017 1.020 1.844 0.534 0.721 24Z 0.765 2.150 3.2

13、10 2.400 2.621 0.785 1.127 1.186 2.125 0.589 0.839 1/ Style D uses class 1 fittings which are made from CRES. 2/ Dimensions are shown on figure 4. FIGURE 4. Style D hose assembly. Source: http:/assist.daps.dla.mil - Downloaded: 2005-09-30T07:35ZCheck the source to verify that this is the current ver

14、sion before use.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS8007C w/AMENDMENT 1 4 Hose assembly dimensions for style E: See table V. TABLE V. Hose assembly dimensions for style E. 1/ 1/ Style E uses class 1 fittings which are made from CRES. 2/

15、 Dimensions are shown on figure 5. FIGURE 5. Style E hose assembly. Hose assembly dimensions for style F: See table Vl. TABLE VI. Hose assembly dimensions for style F. 1/ 1/ Style F uses class 1 fittings which are made from CRES. Dimensions 2/ Fitting ends 1 2 Hose size A (nom) C (max) D (max) E (ma

16、x)F (max)G (min) G (max)P (max)S (max) T (max) U (min) U (max)8 0.438 0.880 1.722 1.332 1.014 0.445 0.632 0.875 2.320 1.422 0.857 0.98210 0.515 0.967 2.037 1.488 1.158 0.501 0.688 1.000 2.875 1.499 0.861 1.01545 90 12 0.570 1.122 2.368 1.667 1.447 0.564 0.775 1.250 3.606 1.807 1.032 1.24616Z 0.620 1

17、.480 2.583 1.879 1.736 0.609 0.857 1.500 3.981 2.174 1.156 1.43420Z 0.640 1.750 2.946 2.058 2.328 0.697 1.017 1.844 4.435 2.590 1.344 1.71524Z 0.765 2.150 3.210 2.400 2.621 0.785 1.127 2.125 5.075 3.103 1.516 2.028Fitting ends Dimensions 2/ 1 2 Hose size A (nom) C (max) F (max) H (max) J (max) K (mi

18、n)K (max) P (max) S (max) T (max) U (min) U (max) 8 0.438 0.880 1.014 2.495 1.938 0.8101.092 0.875 2.320 1.422 0.857 0.982 10 0.515 0.967 1.158 2.955 2.340 1.0561.341 1.000 2.875 1.499 0.861 1.015 90 90 12 0.570 1.122 1.447 3.705 2.722 1.3411.591 1.250 3.606 1.807 1.032 1.246 16Z 0.620 1.480 1.736 4

19、.100 3.075 1.4651.840 1.500 3.981 2.174 1.156 1.434 20Z 0.640 1.750 2.328 4.835 3.637 1.7472.233 1.844 4.435 2.590 1.344 1.715 24Z 0.765 2.150 2.621 5.480 4.212 1.9972.372 2.125 5.075 3.103 1.516 2.028 2/ Dimensions are shown on figure 6. Source: http:/assist.daps.dla.mil - Downloaded: 2005-09-30T07

20、:35ZCheck the source to verify that this is the current version before use.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS8007C w/AMENDMENT 1 5 FIGURE 6. Style F hose assembly. Hose assembly dimensions for style G: See table VIl. TABLE VII. Hose a

21、ssembly dimensions for style G. 1/ Fitting ends Dimensions 2/ 1 2 Hose size A (nom) C (max) D (max) E (max) F (max) G (min) G (max) M (max) P (max) 8 0.438 0.880 1.722 1.332 1.014 0.445 0.632 1.560 0.875 10 0.515 0.967 2.037 1.488 1.158 0.501 0.688 1.570 1.000 45 Straight 12 0.570 1.122 2.368 1.667

22、1.447 0.564 0.775 1.640 1.250 16Z 0.620 1.480 2.583 1.879 1.736 0.609 0.857 1.750 1.500 20Z 0.640 1.750 2.946 2.058 2.328 0.697 1.017 1.990 1.844 24Z 0.765 2.150 3.210 2.400 2.621 0.785 1.127 2.260 2.125 1/ Style G uses class 1 fittings which are made from CRES. 2/ Dimensions are shown on figure 7.

23、FIGURE 7. Style G hose assembly. Source: http:/assist.daps.dla.mil - Downloaded: 2005-09-30T07:35ZCheck the source to verify that this is the current version before use.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS8007C w/AMENDMENT 1 6 Hose asse

24、mbly dimensions for style H: See table VIIl. TABLE VIII. Hose assembly dimensions for style H. 1/ 1/ Style H uses class 1 fittings which are made from CRES. 2/ Dimensions are shown on figure 8. FIGURE 8. Style H hose assembly. Hose assembly dimensions for style J: See table lX. TABLE IX. Hose assemb

25、ly dimensions for style J. 1/ Fitting ends Dimensions 2/ 1 2 Hose size A (nom) C (max) F (max)H (max) J (max) K (min) K (max) M (max) P (max) 8 0.438 0.880 1.014 2.495 1.938 0.810 1.092 1.560 0.875 10 0.515 0.967 1.158 2.995 2.340 1.056 1.341 1.570 1.000 90 Straight 12 0.570 1.122 1.447 3.705 2.722

26、1.341 1.591 1.640 1.250 16Z 0.620 1.480 1.736 4.100 3.075 1.465 1.840 1.750 1.500 20Z 0.640 1.750 2.328 4.835 3.637 1.747 2.233 1.990 1.844 24Z 0.765 2.150 2.621 5.480 4.212 1.997 2.372 2.260 2.125 Dimensions 2/ Fitting ends 1 2 Hose size A (nom) C (max) D (max) F (max) H (max) J (max) K (min) K (ma

27、x)N (max) P (max) R (min) R (max)8 0.438 0.880 1.722 1.014 2.495 1.938 0.810 1.092 0.606 0.875 0.303 0.428 10 0.515 0.967 2.037 1.158 2.955 2.340 1.056 1.341 0.658 1.000 0.340 0.465 90 45 12 0.570 1.122 2.368 1.447 3.705 2.722 1.341 1.591 0.789 1.250 0.433 0.558 16Z 0.620 1.480 2.583 1.736 4.100 3.0

28、75 1.465 1.840 0.929 1.500 0.470 0.657 20Z 0.640 1.750 2.946 2.328 4.835 3.637 1.747 2.233 1.020 1.844 0.534 0.721 24Z 0.765 2.150 3.210 2.621 5.480 4.212 1.997 2.372 1.186 2.125 0.589 0.839 1/ Style J uses class 1 fittings which are made from CRES. 2/ Dimensions are shown on figure 9. Source: http:

29、/assist.daps.dla.mil - Downloaded: 2005-09-30T07:35ZCheck the source to verify that this is the current version before use.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS8007C w/AMENDMENT 1 7 FIGURE 9. Style J hose assembly. Hose assembly dimensio

30、ns for style K: See table X. TABLE X. Hose assembly dimensions for style K. 1/ Fitting ends Dimensions 2/ 1 2 Hose size A (nom) B ( max) C (max) F (max) M (max) P (max) 8 0.438 1.465 0.880 1.014 1.560 0.875 10 0.515 1.680 0.967 1.158 1.570 1.000 Straight Straight 12 0.570 1.727 1.122 1.447 1.640 1.2

31、50 16Z 0.620 2.101 1.480 1.736 1.750 1.500 20Z 0.640 2.255 1.750 2.328 1.990 1.844 24Z 0.765 2.400 2.150 2.621 2.260 2.125 1/ Style K uses class 2 fittings which are made from a combination of aluminum and CRES. 2/ Dimensions are shown on figure 10. FIGURE 10. Style K hose assembly. Source: http:/as

32、sist.daps.dla.mil - Downloaded: 2005-09-30T07:35ZCheck the source to verify that this is the current version before use.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS8007C w/AMENDMENT 1 8 Hose assembly dimensions for style M: See table Xl. TABLE

33、XI. Hose assembly dimensions for style M. 1/ 1/ Style M uses class 2 fittings which are made from a combination of aluminum and CRES. 2/ Dimensions are shown on figure 11. FIGURE 11. Style M hose assembly. Hose assembly dimensions for style N: See table XIl. TABLE XII. Hose assembly dimensions for s

34、tyle N. 1/ Fitting ends Dimensions 2/ 1 2 Hose size A (nom) B (max) C (max) D (max) F (max) N (max) P (max) R (min) R (max) 8 0.438 1.465 0.880 1.722 1.014 0.606 0.875 0.303 0.428 10 0.515 1.680 0.967 2.037 1.158 0.658 1.000 0.340 0.465 Straight 45 12 0.570 1.727 1.122 2.368 1.447 0.789 1.250 0.433

35、0.558 16Z 0.620 2.101 1.480 2.583 1.736 0.929 1.500 0.470 0.657 20Z 0.640 2.255 1.750 2.946 2.328 1.020 1.844 0.534 0.721 24Z 0.765 2.400 2.150 3.210 2.621 1.186 2.125 0.589 0.839 Fitting ends Dimensions 2/ 1 2 Hose size A (nom) B (max) C (max) F (max) P (max) S (max) T (max) U (min) U (max) 8 0.438

36、 1.465 0.880 1.014 0.875 2.320 1.422 0.857 0.982 10 0.515 1.680 0.967 1.158 1.000 2.875 1.499 0.861 1.015 Straight 90 12 0.570 1.727 1.122 1.447 1.250 3.606 1.807 1.032 1.246 16Z 0.620 2.101 1.480 1.736 1.500 3.981 2.174 1.156 1.434 20Z 0.640 2.255 1.750 2.328 1.844 4.435 2.590 1.344 1.715 24Z 0.765

37、 2.400 2.150 2.621 2.125 5.075 3.103 1.516 2.028 1/ Style N uses class 2 fittings which are made from a combination of aluminum and CRES. 2/ Dimensions are shown on figure 12. Source: http:/assist.daps.dla.mil - Downloaded: 2005-09-30T07:35ZCheck the source to verify that this is the current version

38、 before use.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS8007C w/AMENDMENT 1 9 FIGURE 12. Style N hose assembly. Hose assembly dimensions for style P: See table XIIl. TABLE XIII. Hose assembly dimensions for style P. 1/ 1/ Style P uses class 2 f

39、ittings which are made from a combination of aluminum and CRES. Dimensions 2/ Fitting ends 1 2 Hose size A (nom) C (max) D (max) E (max) F (max) G (min) G (max) N (max) P (max) R (min) R (max)8 0.438 0.880 1.722 1.332 1.014 0.445 0.632 0.606 0.875 0.303 0.428 10 0.515 0.967 2.037 1.488 1.158 0.501 0

40、.688 0.658 1.000 0.340 0.465 45 45 12 0.570 1.122 2.368 1.667 1.447 0.564 0.775 0.789 1.250 0.433 0.558 16Z 0.620 1.480 2.583 1.879 1.736 0.609 0.857 0.929 1.500 0.470 0.657 20Z 0.640 1.750 2.946 2.058 2.328 0.697 1.017 1.020 1.844 0.534 0.721 24Z 0.765 2.150 3.210 2.400 2.621 0.785 1.127 1.186 2.12

41、5 0.589 0.839 2/ Dimensions are shown on figure 13. FIGURE 13. Style P hose assembly. Hose assembly dimensions for style R: See table XlV. Source: http:/assist.daps.dla.mil - Downloaded: 2005-09-30T07:35ZCheck the source to verify that this is the current version before use.Provided by IHSNot for Re

42、saleNo reproduction or networking permitted without license from IHS-,-,-MS8007C w/AMENDMENT 1 10 TABLE XIV. Hose assembly dimensions for style R. 1/ 1/ Style R uses class 2 fittings which are made from a combination of aluminum and CRES. Dimensions 2/ Fitting ends 1 2 Hose size A (nom) C (max) D (m

43、ax) E (max)F (max) G (min) G (max) P (max)S (max) T (max) U (min) U (max) 8 0.438 0.880 1.722 1.332 1.014 0.445 0.632 0.875 2.320 1.422 0.857 0.982 10 0.515 0.967 2.037 1.488 1.158 0.501 0.688 1.000 2.875 1.499 0.861 1.015 45 90 12 0.570 1.122 2.368 1.667 1.447 0.564 0.775 1.250 3.606 1.807 1.032 1.

44、246 16Z 0.620 1.480 2.583 1.879 1.736 0.609 0.857 1.500 3.981 2.174 1.156 1.434 20Z 0.640 1.750 2.946 2.058 2.328 0.697 1.017 1.844 4.435 2.590 1.344 1.715 24Z 0.765 2.150 3.210 2.400 2.621 0.785 1.127 2.125 5.075 3.103 1.516 2.028 2/ Dimensions are shown on figure 14. FIGURE 14. Style R hose assemb

45、ly. Hose assembly dimensions for style S: See table XV. Source: http:/assist.daps.dla.mil - Downloaded: 2005-09-30T07:35ZCheck the source to verify that this is the current version before use.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS8007C w/

46、AMENDMENT 1 11 TABLE XV. Hose assembly dimensions for style S. 1/ 1/ Style S uses class 2 fittings which are made from a combination of aluminum and CRES. 2/ Dimensions are shown on figure 15. FIGURE 15. Style S hose assembly. Hose assembly dimensions for style T: See table XVl. TABLE XVI. Hose asse

47、mbly dimensions for style T. 1/ 1/ Style T uses class 2 fittings which are made from a combination of aluminum and CRES. Dimensions 2/ Fitting ends 1 2 Hose size A (nom) C (max) F (max) H (max)J (max)K (min) K (max) P (max)S (max) T (max) U (min) U (max)8 0.438 0.880 1.014 2.495 1.938 0.810 1.092 0.

48、875 2.320 1.422 0.857 0.98210 0.515 0.967 1.158 2.955 2.340 1.056 1.341 1.000 2.875 1.499 0.861 1.01590 90 12 0.570 1.122 1.447 3.705 2.722 1.341 1.591 1.250 3.606 1.807 1.032 1.24616Z 0.620 1.480 1.736 4.100 3.075 1.465 1.840 1.500 3.981 2.174 1.156 1.43420Z 0.640 1.750 2.328 4.835 3.637 1.747 2.233 1.844 4.435 2.590 1.344 1.71524Z 0.765 2.150 2.621 5.480 4.212 1.997 2.372 2.125 5.075 3.103 1.516 2.028Fitting ends Dimensions 2/ 1 2 Hose size A (nom) C (max) D (max) E (max) F (max) G (min) G (max) M (max) P (max) 8 0.43