DLA MS8009 REV C (1)-2005 HOSE ASSEMBLY POLYTETRAFLUOROETHYLENE PERMANENTLY ATTACHED FITTINGS HIGH TEMPERATURE MEDIUM PRESSURE FLANGE-TO-FLANGE《耀斑对耀斑中压高温可重复使用永久配件聚四氟乙烯软管组件》.pdf

1、INCH-POUNDMS8009C w/AMENDMENT 1 09 September 2005 SUPERSEDING MS8009C 24 September 2003 DETAIL SPECIFICATION SHEET HOSE ASSEMBLY, POLYTETRAFLUOROETHYLENE, PERMANENTLY ATTACHED FITTINGS, HIGH TEMPERATURE, MEDIUM PRESSURE, FLANGE-TO-FLANGE This specification is approved for use by all Departments and

2、Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-25579. Hose assembly dimensions for style A: See table l. TABLE I. Hose assembly dimensions for style A. 1/ Fitting ends Dimensions 2/ 1 2 Hose siz

3、e C (max) M (max) P (max) 8 0.880 1.560 0.875 10 0.967 1.570 1.000Straight Straight 12 1.122 1.640 1.250 16Z 1.480 1.750 1.50020Z 1.750 1.990 1.844 24Z 2.150 2.260 2.1251/ Style A uses class 1 fittings which are made from corrosion resistant steel (CRES). 2/ Dimensions are shown on figure 1. FIGURE

4、1. Style A hose assembly. AMSC N/A FSC 4720 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS8009C w/AMENDMENT 1 2 Hose assembly dimensions for style B: See table lI. TABLE II. Hose assembly dimensions for style B. 1/ Fitting ends Dimensions 2/ 1 2

5、Hose size C (max) D (max) M (max) N (max) P (max) R (min) R (max) 8 0.880 1.722 1.560 0.606 0.875 0.303 0.428 10 0.967 2.037 1.570 0.658 1.000 0.340 0.465Straight 45 12 1.122 2.368 1.640 0.789 1.250 0.433 0.558 16Z 1.480 2.583 1.750 0.929 1.500 0.470 0.65720Z 1.750 2.946 1.990 1.020 1.844 0.534 0.72

6、1 24Z 2.150 3.210 2.260 1.186 2.125 0.589 0.8391/ Style B uses class 1 fittings which are made from CRES. 2/ Dimensions are shown on figure 2. FIGURE 2. Style B hose assembly. Hose assembly dimensions for style C: See table lII. TABLE III. Hose assembly dimensions for style C. 1/ Fitting ends Dimens

7、ions 2/ 1 2 Hose size C (max) M (max) P (max) S (max) T (max) U (min) U (max) 8 0.880 1.560 0.875 2.320 1.422 0.857 0.982 10 0.967 1.570 1.000 2.875 1.499 0.861 1.015 Straight 90 12 1.122 1.640 1.250 3.606 1.807 1.032 1.246 16Z 1.480 1.750 1.500 3.981 2.174 1.156 1.434 20Z 1.750 1.990 1.844 4.435 2.

8、590 1.344 1.715 24Z 2.150 2.260 2.125 5.075 3.103 1.516 2.028 1/ Style C uses class 1 fittings which are made from CRES. 2/ Dimensions are shown on figure 3. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS8009C w/AMENDMENT 1 3 FIGURE 3. Style C ho

9、se assembly. Hose assembly dimensions for style D: See table lV. TABLE IV. Hose assembly dimensions for style D. 1/ Dimensions 2/ Fitting ends 1 2 Hose size C (max) D (max) N (max) P (max) R (min) R (max) 8 0.880 1.722 0.606 0.875 0.303 0.428 10 0.967 2.037 0.658 1.000 0.340 0.465 45 45 12 1.122 2.3

10、68 0.789 1.250 0.433 0.558 16Z 1.480 2.583 0.929 1.500 0.470 0.657 20Z 1.750 2.946 1.020 1.844 0.534 0.721 24Z 2.150 3.210 1.186 2.125 0.589 0.839 1/ Style D uses class 1 fittings which are made from CRES. 2/ Dimensions are shown on figure 4. FIGURE 4. Style D hose assembly. Provided by IHSNot for R

11、esaleNo reproduction or networking permitted without license from IHS-,-,-MS8009C w/AMENDMENT 1 4 Hose assembly dimensions for style E: See table V. TABLE V. Hose assembly dimensions for style E. 1/ Dimensions 2/ Fitting ends 1 2 Hose size C (max) D (max) N (max) P (max) R (min) R (max) S (max) T (m

12、ax) U (min) U (max) 8 0.880 1.722 0.606 0.875 0.303 0.428 2.320 1.422 0.857 0.982 10 0.967 2.037 0.658 1.000 0.340 0.465 2.875 1.499 0.861 1.015 45 90 12 1.122 2.368 0.789 1.250 0.433 0.558 3.606 1.807 1.032 1.246 16Z 1.480 2.583 0.929 1.500 0.470 0.657 3.981 2.174 1.156 1.434 20Z 1.750 2.946 1.020

13、1.844 0.534 0.721 4.435 2.590 1.344 1.715 24Z 2.150 3.210 1.186 2.125 0.589 0.839 5.075 3.103 1.516 2.028 1/ Style E uses class 1 fittings which are made from CRES. 2/ Dimensions are shown on figure 5. FIGURE 5. Style E hose assembly. Hose assembly dimensions for style F: See table Vl. TABLE VI. Hos

14、e assembly dimensions for style F. 1/ 1/ Style F uses class 1 fittings which are made from CRES. Dimensions 2/ Fitting ends 1 2 Hose size C (max) P (max) S (max) T (max) U (min) U (max) 8 0.880 0.875 2.320 1.422 0.857 0.982 10 0.967 1.000 2.875 1.499 0.861 1.015 90 90 12 1.122 1.250 3.606 1.807 1.03

15、2 1.246 16Z 1.480 1.500 3.981 2.174 1.156 1.434 20Z 1.750 1.844 4.435 2.590 1.344 1.715 24Z 2.150 2.125 5.075 3.103 1.516 2.028 2/ Dimensions are shown on figure 6. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS8009C w/AMENDMENT 1 5 FIGURE 6. Sty

16、le F hose assembly. Hose assembly dimensions for style G: See table VIl. TABLE VII. Hose assembly dimensions for style G. 1/ 1/ Style G uses class 2 fittings which are made from a combination of aluminum and CRES. Fitting ends Dimensions 2/ 1 2 Hose size C (max) M (max) P (max) 8 0.880 1.560 0.875 1

17、0 0.967 1.570 1.000Straight Straight 12 1.122 1.640 1.250 16Z 1.480 1.750 1.50020Z 1.750 1.990 1.844 24Z 2.150 2.260 2.1252/ Dimensions are shown on figure 7. FIGURE 7. Style G hose assembly. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS8009C w/

18、AMENDMENT 1 6 Hose assembly dimensions for style H: See table VIIl. TABLE VIII. Hose assembly dimensions for style H. 1/ 1/ Style H uses class 2 fittings which are made from a combination of aluminum and CRES. 2/ Dimensions are shown on figure 8. FIGURE 8. Style H hose assembly. Hose assembly dimens

19、ions for style J: See table lX. TABLE IX. Hose assembly dimensions for style J. 1/ 1/ Style J uses class 2 fittings which are made from a combination of aluminum and CRES. Fitting ends Dimensions 2/ 1 2 Hose size C (max) D (max) M (max) N (max) P (max) R (min) R (max) 8 0.880 1.722 1.560 0.606 0.875

20、 0.303 0.428 10 0.967 2.037 1.570 0.658 1.000 0.340 0.465 Straight 45 12 1.122 2.368 1.640 0.789 1.250 0.433 0.558 16Z 1.480 2.583 1.750 0.929 1.500 0.470 0.657 20Z 1.750 2.946 1.990 1.020 1.844 0.534 0.721 24Z 2.150 3.210 2.260 1.186 2.125 0.589 0.839 Fitting ends Dimensions 2/ 1 2 Hose size C (max

21、) M (max) P (max) S (max) T (max) U (min) U (max) 8 0.880 1.560 0.875 2.320 1.422 0.857 0.982 10 0.967 1.570 1.000 2.875 1.499 0.861 1.015 Straight 90 12 1.122 1.640 1.250 3.606 1.807 1.032 1.246 16Z 1.480 1.750 1.500 3.981 2.174 1.156 1.434 20Z 1.750 1.990 1.844 4.435 2.590 1.344 1.715 24Z 2.150 2.

22、260 2.125 5.075 3.103 1.516 2.028 2/ Dimensions are shown on figure 9. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS8009C w/AMENDMENT 1 7 FIGURE 9. Style J hose assembly. Hose assembly dimensions for style K: See table X. TABLE X. Hose assembly

23、dimensions for style K. 1/ 1/ Style K uses class 2 fittings which are made from a combination of aluminum and CRES. Fitting ends Dimensions 2/ 1 2 Hose size C (max) D (max) N (max) P (max) R (min) R (max) 8 0.880 1.722 0.606 0.875 0.303 0.428 10 0.967 2.037 0.658 1.000 0.340 0.465 45 45 12 1.122 2.3

24、68 0.789 1.250 0.433 0.558 16Z 1.480 2.583 0.929 1.500 0.470 0.657 20Z 1.750 2.946 1.020 1.844 0.534 0.721 24Z 2.150 3.210 1.186 2.125 0.589 0.839 2/ Dimensions are shown on figure 10. FIGURE 10. Style K hose assembly. Provided by IHSNot for ResaleNo reproduction or networking permitted without lice

25、nse from IHS-,-,-MS8009C w/AMENDMENT 1 8 Hose assembly dimensions for style M: See table Xl. TABLE XI. Hose assembly dimensions for style M. 1/ 1/ Style M uses class 2 fittings which are made from a combination of aluminum and CRES. 2/ Dimensions are shown on figure 11. FIGURE 11. Style M hose assem

26、bly. Hose assembly dimensions for style N: See table XIl. TABLE XII. Hose assembly dimensions for style N. 1/ 1/ Style N uses class 2 fittings which are made from a combination of aluminum and CRES. Dimensions 2/ Fitting ends 1 2 Hose size C (max) D (max) N (max) P (max) R (min) R (max) S (max) T (m

27、ax) U (min) U (max) 8 0.880 1.722 0.606 0.875 0.303 0.428 2.320 1.422 0.857 0.982 10 0.967 2.037 0.658 1.000 0.340 0.465 2.875 1.499 0.861 1.015 45 90 12 1.122 2.368 0.789 1.250 0.433 0.558 3.606 1.807 1.032 1.246 16Z 1.480 2.583 0.929 1.500 0.470 0.657 3.981 2.174 1.156 1.434 20Z 1.750 2.946 1.020

28、1.844 0.534 0.721 4.435 2.590 1.344 1.715 24Z 2.150 3.210 1.186 2.125 0.589 0.839 5.075 3.103 1.516 2.028 Dimensions 2/ Fitting ends 1 2 Hose size C (max) P (max) S (max) T (max) U (min) U (max) 8 0.880 0.875 2.320 1.422 0.857 0.982 10 0.967 1.000 2.875 1.499 0.861 1.015 90 90 12 1.122 1.250 3.606 1

29、.807 1.032 1.246 16Z 1.480 1.500 3.981 2.174 1.156 1.434 20Z 1.750 1.844 4.435 2.590 1.344 1.715 24Z 2.150 2.125 5.075 3.103 1.516 2.028 2/ Dimensions are shown on figure 12. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS8009C w/AMENDMENT 1 9 FIG

30、URE 12. Style N hose assembly. Protective sleeve code: See table XIII. TABLE XIII. Protective sleeve code. Code TypeA SAE AS1072 sleeve, fire protection, silicone covered, temperature ranging from -65F to 450F and intermittently to 500F, secured with CRES bands as required. 1/ B SAE AS1073 - code B

31、sleeve, abrasion protection, heat shrinkable, black polyolefin, temperature ranging from -65F to 250F. C SAE AS1291 - code A sleeve, chafe guard, extruded seamless white PTFE, temperature ranging from -65F to 450F, secured with CRES bands as required. D SAE AS1291 - code C sleeve, chafe guard, extru

32、ded seamless transparent FEP, temperature ranging from -65F to 350F, secured with CRES bands as required. E SAE AS1298 sleeve, heavy wall chafe guard, extruded seamless black PTFE, temperature ranging from -65F to 450F, secured with CRES bands as required. L Lock-wire hole F Code A + L G Code B + L

33、H Code C + L J Code D + L K Code E + L 1/ To prevent wicking of fluids, the cut ends of the fire protective sleeve (code A) shall be coated with Room Temperature Vulcanized (RTV) silicone rubber prior to installation. After installation, cracks and voids in the fire protective sleeve shall be coated

34、 with RTV rubber to prevent exposure of fiberglass. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS8009C w/AMENDMENT 1 10 Hose assembly size code: See table XIV. TABLE XIV. Hose assembly size code. Size Reference tube OD Size code 8 0.500 H 10 0.6

35、25 J12 0.750 K16Z 1.000 M 20Z 1.250 N24Z 1.500 PREQUIREMENTS Dimensions: Unless otherwise specified, all dimensions are in inches. Dimensions “N (max)” and “T (max)” are installation dimensions and not design dimensions. Fittings: The swivel flange shall conform to MS20756. The nut threads shall be

36、in accordance with SAE AS8879. Assembly classification: Class 1 and class 2 hose assemblies, as specified in MIL-DTL-25579, have been incorporated into the Part or Identifying Number (PIN) as a part of styles. Angular alignment: Hose assemblies with elbow fittings on each end shall have the angular

37、orientation between the elbows measured counter-clockwise from the centerline of the nearest fitting, positioned at six-oclock, to the centerline of the other fitting (see figure 13). When applicable, the angular alignment shall be expressed in three digits and specified in the PIN. Protective sleev

38、e: If required, the hose assembly shall include a protective sleeve (see table XIII) and its code shall be included in the PIN. Fire protective sleeve shall be subjected to testing in accordance with MIL-DTL-25579. Assembly length: Hose assembly shall be furnished in lengths as specified in the cont

39、ract or purchase order (see MIL-DTL-25579); however, tolerances on the length of each hose assembly shall be as follows: a. 1/8 inch for lengths under 18 inches. b. 1/4 inch for lengths from 18 inches to 36 inches. c. 1/2 inch for lengths from 36 inches to 50 inches. d. 1% for lengths over 50 inches

40、. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS8009C w/AMENDMENT 1 11 NOTE: Angular alignment shall be measured in degrees with a tolerance of FIGURE 13. Measurement of angular alignment between elbow fittingsPIN: The PIN for each hose assembly

41、shall include its size code, length, style,and the angular alignment between the elbow fittings, as applicable. Example: The PIN for an 8.250 inch (209.55 mm) length, style F hose assembly with a 0.500 inch (12.70 mm) tube OD, a fire protective sleeve in accordance with SAE AS1072, and a 30elbow fit

42、tings shall be as follows: 08 2 F AH MS8009 030ProtecLeave blank if not required. If a protective sleeve is not required, the PIN shall be as follows: MS8009H082F030. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-2. . protective sleeve type, betwee

43、n the Angular alignment between elbow fittings as specified on figure 13 (leave blank for styles A, B, C, G, H, and J.tive sleeve type (see table XIII). Style (see table VI and figure 6). Length in eights of an inch. Length in inches.Size code (see table XIV). Specification number. MS8009C w/AMENDME

44、NT 1 12 Amendment notations. The margins of this specification are marked with vertical lines to indicate modifications generated by this amendment. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors

45、 are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations. Referenced documents. In addition to MIL-DTL-25579, this document references the following: MS20756 SAE AS1072 SAE AS1073 SAE AS1291 SAE AS1298 SAE AS8879 CONCLUDING MATER

46、IAL Custodians: Preparing activity:Army - AV DLA - CC Navy - AS Air Force - 99 (Project 4720-0436-000) DLA - CC Review activities: Army - AR, AT, EA, MI Navy - MC, SA, SH Air Force - 70 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-