DLA MS9036 REV C-2008 BOLT-MACHINE 12 POINT HEAD HEAT RESISTANT STEEL 375-24 NS《375-24 NS耐热钢13角头螺栓机》.pdf

1、 INCH-POUNDMS9036C 17 April 2008SUPERSEDING MS9036B 29 AUGUST 1986 MILITARY SPECIFICATION SHEET BOLT-MACHINE, 12 POINT HEAD, HEAT RESISTANT STEEL, .375-24 NS Inactive for new design after 6 April 1967 This specification sheet is approved for use by all Departments and Agencies of the Department of D

2、efense. The requirements for acquiring the product described herein shall consist of this specification sheet and SAE-AS 7478. FIGURE 1. Machine bolt AMSC N/A FSC 5305 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS9036C 2 TABLE I. Dash numbers an

3、d dimensionsDASH NO. L K +.000 -.060 APPROX WEIGHT LBS/100 DASH NO. L K +.000 -.060 APPROX WEIGHT LBS/100 DASH NO. L K +.000 -.060 APPROX WEIGHT LBS/100 -06 -07 -08 -09 -10 -11 -12 -13 -14 -15 -16 -17 -18 -19 -20 -21 -22 .750 .812 .875 .938 1.000 1.062 1.125 1.188 1.250 1.312 1.375 1.438 1.500 1.562

4、 1.625 1.688 1.750 1/ 1/ 1/ 1/ 1/ 1/ .125 .188 .250 .312 .375 .438 .500 .562 .625 .688 .750 3.74 3.90 4.07 4.24 4.41 4.58 4.75 4.91 5.08 5.25 5.43 5.60 5.76 5.93 6.10 6.27 6.44 -23 -24 -25 -26 -27 -28 -29 -30 -31 -32 -33 -34 -35 -36 -37 -38 -39 1.875 2.000 2.125 2.250 2.375 2.500 2.625 2.750 2.875 3

5、.000 3.125 3.250 3.375 3.500 3.625 3.750 3.875 .875 1.000 1.125 1.250 1.375 1.500 1.625 1.750 1.875 2.000 2.125 2.250 2.375 2.500 2.625 2.750 2.875 6.77 7.11 7.44 7.78 8.11 8.44 8.78 9.12 9.46 9.80 10.13 10.47 10.80 11.14 11.47 11.80 12.14 -40 -41 -42 -43 -44 -45 -46 -47 -48 -49 -50 -51 -52 -53 -54

6、-55 -56 4.000 4.125 4.250 4.375 4.500 4.625 4.750 4.875 5.000 5.125 5.250 5.375 5.500 5.625 5.750 5.875 6.000 3.000 3.125 3.250 3.375 3.500 3.625 3.750 3.875 4.000 4.125 4.250 4.375 4.500 4.625 4.750 4.875 5.000 12.47 12.80 13.13 13.46 13.89 14.23 14.56 14.89 15.23 15.57 15.90 16.23 16.56 16.89 17.2

7、3 17.57 17.91 1/ THREAD TO HEAD. MAXIMUM TWO INCOMPLETE THREADS REQUIREMENTS: 1. MATERIAL: HEAT RESISTANCE STEEL IN ACCORDANCE WITH SAE-AMS5732. 2. THREADS: THREADS IN ACCORDANCE WITH MIL-S-7742. INCOMPLETE THREADS NOT TO ENTER FILLET. 3. DIMENSIONING AND TOLERANCING: DIMENSIONING AND TOLERANCING SH

8、ALL BE IN ACCORDANCE WITH ASME Y14.5M. 4. SURFACE TEXTURE: SURFACE TEXTURE, UNLESS OTHERWISE SPECIFIED,SHALL BE 125 MICROINCHES EXCEPT UPSET HEAD IN ACCORDANCE WITH ASME B46.1. 5. FLUORESCENT PENETRANT INSPECTION: FLUORESCENT PENETRANT INSPECTION SHALL BE IN ACCORDANCE WITH ASTM E1417. 6. TOLERANCE:

9、 UNLESS OTHERWISE SPECIFIED, TOLERANCES SHALL BE FOR LINEAR DIMENSIONS +.010, ANGULAR DIMENSION +5. 7. EDGES: BREAK SHARP EDGES .003-.015 UNLESS OTHERWISE SPECIFIED. 8. PART NUMBER: THE PART NUMBER SHALL CONSIST OF THE BASIC MS NUMBER FOLLOWED BY A DASH NUMBER FROM TABLE I. EXAMPLE: MS9036- 06DASH N

10、UMBER BASIC MS NUMBER MS9036-06 INDICATES - BOLT, MACHINE, 12 POINT HEAD, HEAT RESISTANT STEEL ,.375-24 NS, LENGTH .750.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS9036C 3 NOTES: 1. ALL DIMENSIONS ARE IN INCHES. 2. DO NOT USE UNASSIGNED PART NU

11、MBERS. 3. IN THE EVENT OF A CONFLICT BETWEEN THE TEXT OF THIS STANDARD AND THE REFERENCES CITED HEREIN, THE TEXT OF THIS STANDARD SHALL TAKE PRECEDENCE. 4. REFERENCED GOVERNMENT (OR NON-GOVERNMENT ) DOCUMENTS OF THE ISSUE LISTED IN THAT ISSUE OF THE DEPARTMENT OF DEFENSE INDEX OF SPECIFICATIONS AND

12、STANDARDS (DODISS) SPECIFIED IN THE SOLICITATION FORM A PART OF THIS STANDARD TO THE EXTENT SPECIFIED HEREIN. 5. THIS STANDARD WAS DEVELOPED COOPERATIVELY WITH THE SAE AEROSPACE PROPULSION DIVISION. 6. AS AND AMS ARE SAE PUBLICATIONS. 7. SUBJECT TERM (KEY WORD) LISTING . BOLT, MACHINE, 12 POINT HEAD

13、, HEAT RESISTANT STEEL. 8. CHANGES FROM PREVIOUS ISSUE. THE MARGINS OF THIS SPECIFICATION ARE MARKED WITH VERTICAL LINES TO INDICATE WHERE CHANGES FROM THE PREVIOUS ISSUE WERE MADE. THIS WAS DONE AS A CONVENIENCE ONLY AND THE GOVERNMENT ASSUMES NO LIABILITY WHATSOEVER FOR ANY INACCURACIES IN THESE N

14、OTATIONS. BIDDERS AND CONTRACTORS ARE CAUTIONED TO EVALUATE THE REQUIREMENTS OF THIS DOCUMENT BASED ON THE ENTIRE CONTENT IRRESPECTIVE OF THE MARGINAL NOTATIONS AND RELATIONSHIP TO THE LAST PREVIOUS ISSUE. Custodians: Preparing activity: Navy - AS DLA IS DLA IS (Project 5305-2008-002) NOTE: The acti

15、vities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.milProvided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-