DLA MS9193 REV A-2010 NIPPLE TUBE - SAE-AMS5639 BOSS.pdf

1、 MS9193A 16 February 2010 SUPERSEDING MS9193 (ASG) 11 April 1960 DETAIL SPECIFICATION SHEET NIPPLE, TUBE - SAE-AMS5639, BOSS This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist

2、of this specification sheet and SAE-AS4841. FIGURE 1. Nipple, tube, boss. AMSC N/A FSC 4730INCH-POUND Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS9193A 2 FIGURE 1. Nipple, tube, boss - Continued. Inches mm .005 .010 .020 0.13 0.25 0.51 Provided

3、 by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS9193A 3 Dash number Tube OD (reference) inches (mm) A inches (mm) B inches (mm) +.015 (0.38) -.000 C diameter inches (mm) +.000 -.010 (0.25) -02 .125 (3.18) .058 (1.47) - .065 (1.65) .144 (3.66) .245 (6.22) -

4、03 .188 (4.78) .121 (3.07) - .128 (3.25) .144 (3.66) .307 (7.80) -04 .250 (6.35) .168 (4.27) - .175 (4.45) .160 (4.06) .359 (9.12) -05 .313 (7.95) .230 (5.84) - .237 (6.02) .160 (4.06) .421 (10.69) -06 .375 (9.53) .293 (7.44) - .301 (7.65) .165 (4.19) .476 (12.09) -07 .438 (11.13) .355 (9.02) - .363

5、 (9.22) .165 (4.19) .539 (13.69) -08 .500 (12.70) .387 (9.83) - .395 (10.03) .229 (5.82) .654 (16.61) -09 .562 (14.27) .434 (11.02) - .442 (11.23) .229 (5.82) .716 (18.19) -10 .625 (15.88) .480 (12.19) - .488 (12.40) .255 (6.48) .767 (19.48) -11 .688 (17.48) .542 (13.77) - .552 (14.02) .304 (7.72) .

6、875 (22.23) -12 .750 (19.05) .604 (15.34) - .614 (15.60) .304 (7.72) .938 (23.83) -14 .875 (22.23) .729 (18.52) - .739 (18.77) .304 (7.72) 1.062 (26.97) -16 1.000 (25.40) .839 (21.31) - .851 (21.62) .312 (7.92) 1.188 (30.18) -18 1.125 (28.58) .948 (24.08) - .960 (24.38) .312 (7.92) 1.375 (34.93) -20

7、 1.250 (31.75) 1.073 (27.25) - 1.086 (27.58) .363 (9.22) 1.500 (38.10) -24 1.500 (38.10) 1.307 (33.20) - 1.320 (33.53) .374 (9.50) 1.750 (44.45) -28 1.750 (44.45) 1.542 (39.17) - 1.557 (39.55) .447 (11.35) 2.125 (53.98) -32 2.000 (50.80) 1.776 (45.11) - 1.791 (45.49) .457 (11.61) 2.375 (60.33) FIGUR

8、E 1. Nipple, tube, boss - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS9193A 4 Dash number D diameter inches (mm) .003 (0.08) E inches (mm) F diameter inches (mm) +.002 (0.05) -.003 (0.08) (see notes 4 and 5) G minimum inches (mm) H i

9、nches (mm) -02 .132 (3.35) .063 (1.60) .250 (6.35) .631 (16.03) .553 (14.05) - .564 (14.33) -03 .195 (4.95) .063 (1.60) .312 (7.92) .703 (17.86) .616 (15.65) - .627 (15.93) -04 .242 (6.15) .075 (1.91) .364 (9.25) .775 (19.69) .679 (17.25) - .690 (17.53) - -05 .304 (7.72) .075 (1.91) .426 (10.82) .84

10、6 (21.49) .741 (18.82) - .752 (19.10) -06 .368 (9.35) .083 (2.11) .481 (12.22) .916 (23.27) .803 (20.40) - .814 (20.68) -07 .430 (10.92) .083 (2.11) .544 (13.82) .987 (25.07) .865 (21.97) - .877 (22.28) -08 .462 (11.73) .094 (2.39) .660 (16.76) 1.130 (28.70) .990 (25.15) - 1.062 (26.97) -09 .509 (12

11、.93) .094 (2.39) .722 (18.34) 1.200 (30.48) 1.052 (26.72) - 1.064 (27.03) -10 .555 (14.10) .107 (2.72) .773 (19.63) 1.270 (32.26) 1.114 (28.30) - 1.127 (28.63) -11 .619 (15.72) .125 (3.18) .882 (22.40) 1.484 (37.69) 1.301 (33.05) - 1.314 (33.38) -12 .681 (17.30) .125 (3.18) .945 (24.00) 1.556 (39.52

12、) 1.364 (34.65) - 1.377 (34.98) -14 .806 (20.47) .125 (3.18) 1.070 (27.18) 1.699 (43.15) 1.489 (37.82) - 1.502 (38.15) -16 .918 (23.32) .125 (3.18) 1.195 (30.35) 1.842 (46.79) 1.614 (41.00) - 1.627 (41.33) -18 1.027 (26.09) .125 (3.18) 1.382 (35.10) 1.983 (50.37) 1.738 (44.15) - 1.752 (44.50) -20 1.

13、153 (29.29) .125 (3.18) 1.507 (38.28) 2.126 (54.00) 1.863 (47.32) - 1.877 (47.68) -24 1.387 (35.23) .125 (3.18) 1.756 (44.60) 2.411 (61.24) 2.113 (53.67) - 2.127 (54.03) -28 1.652 (41.96) .125 (3.18) 2.131 (54.13) 2.839 (72.11) 2.488 (63.20) - 2.502 (63.55) -32 1.886 (47.90) .125 (3.18) 2.381 (60.48

14、) 3.124 (79.35) 2.738 (69.55) - 2.752 (69.90) FIGURE 1. Nipple, tube, boss - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS9193A 5 Dash number J inches (mm) K inches (mm) L inches (mm) M min inches (mm) -02 .415 (10.54) .360 (9.14) .60

15、5 (15.37) .030 (0.76) -03 .446 (11.33) .360 (9.14) .636 (16.15) .030 (0.76) -04 .517 (13.13) .400 (10.16) .737 (18.72) .030 (0.76) -05 .517 (13.13) .400 (10.16) .737 (18.72) .030 (0.76) -06 .523 (13.28) .400 (10.16) .773 (19.63) .030 (0.76) -07 .523 (13.28) .440 (11.18) .773 (19.63) .030 (0.76) -08

16、.633 (16.08) .440 (11.18) .883 (22.43) .030 (0.76) -09 .633 (16.08) .440 (11.18) .883 (22.43) .030 (0.76) -10 .747 (18.97) .440 (11.18) 1.057 (26.85) .030 (0.76) -11 .853 (21.67) .440 (11.18) 1.163 (29.54) .030 (0.76) -12 .853 (21.67) .480 (12.19) 1.163 (29.54) .030 (0.76) -14 .898 (22.81) .480 (12.

17、19) 1.208 (30.68) .030 (0.76) -16 .908 (23.06) .480 (12.19) 1.268 (32.21) .030 (0.76) -18 .954 (24.23) .480 (12.19) 1.314 (33.38) .030 (0.76) -20 .954 (24.23) .480 (12.19) 1.314 (33.38) .030 (0.76) -24 1.079 (27.41) .480 (12.19) 1.439 (36.55) .030 (0.76) -28 1.204 (30.58) .480 (12.19) 1.594 (40.49)

18、.044 (1.12) -32 1.329 (33.76) .480 (12.19) 1.719 (43.66) .044 (1.12) FIGURE 1. Nipple, tube, boss - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS9193A 6 Dash number P inches (mm) R radius Thread T (see note 11) -02 .020 (0.51) - .050

19、(1.27) .562 (14.27) .3125 - 24UNF-3A -03 .020 (0.51) - .050 (1.27) .625 (15.88) .375 - 24UNF-3A -04 .030 (0.76) - .060 (1.52) .688 (17.48) .4375 - 20UNF-3A -05 .030 (0.76) - .070 (1.78) .750 (19.05) .500 - 20UNF-3A -06 .040 (1.02) - .070 (1.78) .812 (20.62) .5625 - 18UNF-3A -07 .040 (1.02) - .070 (1

20、.78) .875 (22.23) .625 - 18UNF-3A -08 .040 (1.02) - .070 (1.78) 1.000 (25.40) .7500 - 16UNF-3A -09 .040 (1.02) - .070 (1.78) 1.062 (26.97) .8125 - 16UN-3A -10 .050 (1.27) - .080 (2.03) 1.125 (28.58) .8750 - 14UNF-3A -11 .050 (1.27) - .080 (2.03) 1.312 (33.32) 1.000 - 12UNF-3A -12 .050 (1.27) - .080

21、(2.03) 1.375 (34.93) 1.0625 - 12UN-3A -14 .050 (1.27) - .080 (2.03) 1.500 (38.10) 1.1875 - 12UN-3A -16 .050 (1.27) - .080 (2.03) 1.625 (41.28) 1.3125 - 12UN-3A -18 .050 (1.27) - .080 (2.03) 1.750 (44.45) 1.500 - 12UNF-3A -20 .050 (1.27) - .080 (2.03) 1.875 (47.63) 1.625- 12UN-3A -24 .050 (1.27) - .0

22、80 (2.03) 2.125 (53.98) 1.8750 - 12UN-3A -28 .050 (1.27) - .080 (2.03) 2.500 (63.50) 2.2500 - 12UN-3A -32 .050 (1.27) - .080 (2.03) 2.750 (69.85) 2.500 - 12UN-3A FIGURE 1. Nipple, tube, boss - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-

23、,-MS9193A 7 Dash number Thread TT (see note 11) Size Major diameter inches (mm) Pitch diameter inches (mm) Minor diameter max inches (mm) -02 .3125 24UNS-3A .3023 (7.678) - .3095 (7.861) .2797 (7.104) - .2824 (7.173) .2584 (6.563) -03 .375 24UNS-3A .3648 (9.266) - .3720 (9.449) .3420 (8.687) - .3449

24、 (8.760) .3209 (8.151) -04 .4375 20UNS-3A .4264 (10.831) - .4345 (11.036) .3989 (10.132) - .4020 (10.211) .3732 (9.479) -05 .500 20UNS-3A .4889 (12.418) - .4970 (12.623) .4613 (11.717) - .4645 (11.80) .4357 (11.067) -06 .5625 18UNS-3A .5508 (13.990) - .5595 (14.211) .5200 (13.208) - .5234 (13.294) .

25、4913 (12.479) -07 .625 18UNS-3A .6133 (15.578) - .6220 (15.799) .5824 (14.793) - .5859 (14.881) .5538 (14.067) -08 .750 16UNS-3A .7376 (18.735) - .7470 (18.974) .7026 (17.846) - .7064 (17.942) .6703 (17.026) -09 .8125 16UNS-3A .8001 (20.323) - .8095 (20.561) .7653 (19.44) - .7689 (19.530) .7328 (18.

26、613) -10 .875 14UNS-3A .8617 (21.887) - .8720 (22.149) .8215 (20.866) - .8256 (20.970) .7844 (19.924) -11 1.000 12UNS-3A .9856 (25.034) - .9970 (25.324) .9385 (23.838) - .9429 (23.950) .8948 (22.728) -12 1.0625 12UNS-3A 1.0481 (26.622) - 1.0595 (26.911) 1.0012 (25.430) - 1.0054 (25.537) .9573 (24.31

27、5) -14 1.1875 12UNS-3A 1.1731 (29.797) - 1.1845 (30.086) 1.1261 (28.603) - 1.1304 (28.712) 1.0823 (27.490) -16 1.3125 12UNS-3A 1.2981 (32.972) - 1.3095 (33.261) 1.2511 (31.778) - 1.2554 (31.887) 1.2073 (30.665) -18 1.500 12UNS-3A 1.4856 (37.734) - 1.4970 (38.024) 1.4381 (36.528) - 1.4429 (36.650) 1.

28、3948 (35.428) -20 1.625 12UNS-3A 1.6106 (40.909) - 1.6220 (41.199) 1.5635 (39.713) - 1.5679 (39.825) 1.5198 (38.603) -24 1.875 12UNS-3A 1.8606 (47.259) - 1.8720 (47.549) 1.8134 (46.060) - 1.8179 (46.175) 1.7698 (44.953) -28 2.250 12UNS-3A 2.2356 (56.784) - 2.2470 (57.074) 2.1884 (55.585) - 2.1929 (5

29、5.700) 2.1448 (54.478) -32 2.500 12UNS-3A 2.4856 (63.134) - 2.4970 (63.424) 2.4429 (62.050) - 2.4383 (61.933) 2.3948 (60.828) FIGURE 1. Nipple, tube, boss - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS9193A 8 NOTES: 1. Dimensions are

30、 in inches. 2. Metric equivalents are given for information only. 3. Unless otherwise specified tolerances for linear dimensions are .010 inch (0.25 mm) and angular dimensions are 5, all dimensions concentric within .010 inch (0.25 mm) FIM. 4. Unless otherwise specified surfaces to be 125 inches (3.

31、18m) in accordance with AMSE B46.1. 5. Diameter F shall be free of thread marks. 6. Diameter F shall be concentric with PD of thread within .0025 inch (1.134 mm) FIM. 7. Lettering height: a. For size -02 through -04: .020 - .040 inch (0.51 - 1.02 mm). b. For size -05 through -16: .040 - .060 inch (1

32、.02 - 1.52 mm). c. For size -18 and larger: .090 - .150 inch (2.29 - 3.81 mm) 8. All diameters shall be concentric within .010 inch (0.25 mm) FIM unless otherwise specified. 9. Parting line mismatch .015 inch (0.38 mm) max. 10. Unless otherwise specified break sharp edges .003 - .015 inches (0.08 -

33、0.38 mm). 11. Threads shall be in accordance with FED-STD-H28/2. FIGURE 1. Nipple, tube, boss - Continued. REQUIREMENTS: Dimensions and configurations: See figure 1. Material: Steel, corrosion and heat-resistant in accordance with SAE-AMS5639. Max operating temperature: Oxidation resistance up to 15

34、00F (816C). Max operating pressure: 1500 psi (10 MPa). Finish: Passivate in accordance with SAE-AMS2700, method 1. PIN: MS9193 -08 PIN Example: MS9193-08 identifies a nipple .500 inch (tube), CRES. Do not use unassigned PINs. The approximate weight for each fitting is shown in table I. Specification

35、 sheet number Nipple size (see figure 1) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS9193A 9 TABLE I. Approximate weight. Dash number Approximate weight lbs/ea (grams/ea) Dash number Approximate weight lbs/ea (grams/ea) -02 .026 (12) -11 .255 (

36、116) -03 .034 (15) -12 .282 (128) -04 .048 (22) -14 .331 (150) -05 .057 (26) -16 .407 (185) -06 .069 (31) -18 .522 (237) -07 .080 (36) -20 .573 (260) -08 .125 (57) -24 .739 (335) -09 .141 (64) -28 1.176 (533) -10 .182 (83) -32 1.433 (650) Intended usage: Jet engine, miscellaneous parts, oil, fuel, a

37、nd de-icing kits. Not to be used on hydraulic, oxygen or applications requiring pressures of 3000 psi (21 MPa). Changes from previous issue. Marginal notations are not used in this revision to identify changes with respect to the previous issue due to the extent of the changes. Referenced documents.

38、 In addition to SAE-AS4841, this document references the following: FED-STD-H28/2 AMSE B46.1 SAE-AMS2700 SAE-AMS2800 SAE-AMS5639 CONCLUDING MATERIAL Custodians: Preparing activity: Army - MI DLA - CC Navy - AS DLA - CC (Project 4730-2009-079) Review activity: Navy - SA NOTE: The activities listed ab

39、ove were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-