DLA MS9194 REV C-2010 ELBOW TUBE - SAE-AMS5646 BOSS 90 DEGREES.pdf

1、 MS9194C 16 February 2010 SUPERSEDING MS9194B (ASG) 27 July 1967 DETAIL SPECIFICATION SHEET ELBOW, TUBE - SAE-AMS5646, BOSS, 90 This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consi

2、st of this specification sheet and SAE-AS4841. FIGURE 1. Elbow, tube, boss, 90. AMSC N/A FSC 4730INCH-POUND Inactive for new design after 20 September 2000. Inches mm .005 .020 .030 0.13 0.51 0.76 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS919

3、4C 2 Dash number Tube OD (reference) inches (mm) A diameter inches (mm) B inches (mm) +.015 (0.38) -.000 C diameter inches (mm) +.000 -.010 (0.25) -02 .125 (3.18) .058 (1.47) - .065 (1.65) .144 (3.66) .245 (6.22) -03 .188 (4.78) .121 (3.07) - .128 (3.25) .144 (3.66) .307 (7.80) -04 .250 (6.35) .168

4、(4.27) - .175 (4.45) .160 (4.06) .359 (9.12) -05 .313 (7.95) .230 (5.84) - .237 (6.02) .160 (4.06) .421 (10.69) -06 .375 (9.53) .293 (7.44) - .301 (7.65) .165 (4.19) .476 (12.09) -07 .438 (11.13) .355 (9.02) - .363 (9.22) .165 (4.19) .539 (13.69) -08 .500 (12.70) .387 (9.83) - .395 (10.03) .229 (5.8

5、2) .654 (16.61) -09 .562 (14.27) .434 (11.02) - .442 (11.23) .229 (5.82) .716 (18.19) -10 .625 (15.88) .480 (12.19) - .488 (12.40) .255 (6.48) .767 (19.48) -11 .688 (17.48) .542 (13.77) - .552 (14.02) .304 (7.72) .875 (22.23) -12 .750 (19.05) .604 (15.34) - .614 (15.60) .304 (7.72) .938 (23.83) -14

6、.875 (22.23) .729 (18.52) - .739 (18.77) .304 (7.72) 1.062 (26.97) -16 1.000 (25.40) .839 (21.31) - .851 (21.62) .312 (7.92) 1.188 (30.18) -18 1.125 (28.58) .948 (24.08) - .960 (24.38) .312 (7.92) 1.375 (34.93) -20 1.250 (31.75) 1.073 (27.25) - 1.086 (27.58) .363 (9.22) 1.500 (38.10) -24 1.500 (38.1

7、0) 1.307 (33.20) - 1.320 (33.53) .374 (9.50) 1.750 (44.45) -28 1.750 (44.45) 1.542 (39.17) - 1.557 (39.55) .447 (11.35) 2.125 (53.98) -32 2.000 (50.80) 1.776 (45.11) - 1.791 (45.49) .457 (11.61) 2.375 (60.33) FIGURE 1. Elbow, tube, boss, 90- Continued. Provided by IHSNot for ResaleNo reproduction or

8、 networking permitted without license from IHS-,-,-MS9194C 3 Dash number D diameter inches (mm) .003 (0.08) E (see note 10) inches (mm) F diameter inches (mm) +.002 (0.05) -.003 (0.08) (see notes 5 and 6) G diameter inches (mm) H inches (mm) .010 (0.25) -02 .132 (3.35) .040 (1.02) .250 (6.35) .240 (

9、6.10) .208 (5.28) -03 .195 (4.95) .040 (1.02) .312 (7.92) .300 (7.62) .208 (5.28) -04 .242 (6.15) .040 (1.02) .364 (9.25) .350 (8.89) .250 (6.35) -05 .304 (7.72) .050 (1.27) .426 (10.82) .415 (10.54) .250 (6.35) -06 .368 (9.35) .050 (1.27) .481 (12.22) .470 (11.94) .278 (7.06) -07 .430 (10.92) .060

10、(1.52) .544 (13.82) .535 (13.59) .278 (7.06) -08 .462 (11.73) .080 (2.03) .660 (16.76) .650 (16.51) .312 (7.92) -09 .509 (12.93) .090 (2.29) .722 (18.34) .710 (18.03) .312 (7.92) -10 .555 (14.10) .090 (2.29) .773 (19.63) .765 (19.43) .357 (9.07) -11 .619 (15.72) .110 (2.79) .882 (22.40) .870 (22.10)

11、 .417 (10.59) -12 .681 (17.30) .110 (2.79) .945 (24.00) .935 (23.75) .417 (10.59) -14 .808 (20.52) .110 (2.79) 1.070 (27.18) 1.055 (26.80) .417 (10.59) -16 .918 (23.32) .110 (2.79) 1.195 (30.35) 1.185 (30.10) .417 (10.59) -18 1.027 (26.09) .150 (3.81) 1.382 (35.10) 1.365 (34.67) .417 (10.59) -20 1.1

12、53 (29.29) .150 (3.81) 1.507 (38.28) 1.495 (37.97) .417 (10.59) -24 1.387 (35.23) .170 (4.32) 1.756 (44.60) 1.745 (44.32) .417 (10.59) -28 1.652 (41.96) .240 (6.10) 2.131 (54.13) 2.120 (53.85) .417 (10.59) -32 1.886 (47.90) .250 (6.35) 2.381 (60.48) 2.370 (60.20) .417 (10.59) FIGURE 1. Elbow, tube,

13、boss, 90 - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS9194C 4 Dash number J inches (mm) .010 (0.25) K inches (mm) .010 (0.25) M min inches (mm) N inches (mm) +.010 (0.25) -.000 -02 .317 (8.05) .682 (17.32) .030 (0.76) .125 (3.18) -0

14、3 .346 (8.79) .682 (17.32) .030 (0.76) .131 (3.33) -04 .398 (10.11) .748 (19.00) .030 (0.76) .140 (3.56) -05 .398 (10.11) .748 (19.00) .030 (0.76) .140 (3.56) -06 .398 (10.11) .813 (20.65) .030 (0.76) .156 (3.96) -07 .398 (10.11) .813 (20.65) .030 (0.76) .172 (4.37) -08 .489 (12.42) .903 (22.94) .03

15、0 (0.76) .187 (4.75) -09 .489 (12.42) .903 (22.94) .030 (0.76) .203 (5.16) -10 .585 (14.86) 1.018 (25.86) .030 (0.76) .219 (5.56) -11 .663 (16.84) 1.122 (28.50) .030 (0.76) .234 (5.94) -12 .663 (16.84) 1.122 (28.50) .030 (0.76) .234 (5.94) -14 .710 (18.03) 1.122 (28.50) .030 (0.76) .234 (5.94) -16 .

16、720 (18.29) 1.122 (28.50) .030 (0.76) .234 (5.94) -18 .767 (19.48) 1.122 (28.50) .030 (0.76) .234 (5.94) -20 .767 (19.48) 1.122 (28.50) .030 (0.76) .234 (5.94) -24 .889 (22.58) 1.122 (28.50) .030 (0.76) .234 (5.94) -28 1.017 (25.83) 1.205 (30.61) .044 (1.12) .234 (5.94) -32 1.142 (29.01) 1.320 (33.5

17、3) .044 (1.12) .234 (5.94) FIGURE 1. Elbow, tube, boss, 90 - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS9194C 5 Dash number P inches (mm) Q inches (mm) .010 (0.25) R radius inches (mm) S inches (mm) +.010 (0.25 mm) -02 .020 (0.51) -

18、 .050 (1.27) .707 (17.96) .120 (3.05) 1.000 (25.40) -03 .020 (0.51) - .050 (1.27) .764 (19.41) .150 (3.81) 1.000 (25.40) -04 .030 (0.76) - .060 (1.52) .826 (20.98) .175 (4.45) 1.115 (28.32) -05 .030 (0.76) - .060 (1.52) .889 (22.58) .207 (5.26) 1.140 (28.96) -06 .040 (1.02) - .070 (1.78) .998 (25.35

19、) .235 (5.97) 1.270 (32.26) -07 .040 (1.02) - .070 (1.78) .998 (25.35) .267 (6.78) 1.305 (33.15) -08 .040 (1.02) - .070 (1.78) 1.195 (30.35) .325 (8.26) 1.460 (37.08) -09 .040 (1.02) - .070 (1.78) 1.195 (30.35) .355 (9.02) 1.490 (37.85) -10 .050 (1.27) - .080 (2.03) 1.411 (35.84) .382 (9.70) 1.680 (

20、42.67) -11 .050 (1.27) - .080 (2.03) 1.614 (41.00) .435 (11.05) 1.855 (47.12) -12 .050 (1.27) - .080 (2.03) 1.614 (41.00) .467 (11.86) 1.885 (47.88) -14 .050 (1.27) - .080 (2.03) 1.768 (44.91) .527 (13.39) 1.945 (49.40) -16 .050 (1.27) - .080 (2.03) 1.778 (45.16) .592 (15.04) 2.010 (51.05) -18 .050

21、(1.27) - .080 (2.03) 2.027 (51.49) .682 (17.32) 2.100 (53.34) -20 .050 (1.27) - .080 (2.03) 2.027 (51.49) .750 (19.05) 2.165 (54.99) -24 .050 (1.27) - .080 (2.03) 2.293 (58.24) .872 (22.15) 2.290 (58.17) -28 .050 (1.27) - .080 (2.03) 2.777 (70.54) 1.062 (26.97) 2.625 (66.68) -32 .050 (1.27) - .080 (

22、2.03) 3.027 (76.89) 1.188 (30.18) 2.975 (75.57) FIGURE 1. Elbow, tube, boss, 90 - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS9194C 6 Dash number Thread T (see note 13) -02 .3125 - 24UNF-3A -03 .375 - 24UNF-3A -04 .4375 - 20UNF-3A -0

23、5 .500 - 20UNF-3A -06 .5625 - 18UNF-3A -07 .625 - 18UNF-3A -08 .7500 - 16UNF-3A -09 .8125 - 16UN-3A -10 .8750 - 14UNF-3A -11 1.000 - 12UNF-3A -12 1.0625 - 12UN-3A -14 1.1875 - 12UN-3A -16 1.3125 - 12UN-3A -18 1.500 - 12UNF-3A -20 1.625- 12UN-3A -24 1.8750 - 12UN-3A -28 2.2500 - 12UN-3A -32 2.500 - 1

24、2UN-3A FIGURE 1. Elbow, tube, boss, 90 - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS9194C 7 Dash number Thread TT (see note 13) Size Major diameter inches (mm). Pitch diameter inches (mm) Minor diameter max inches (mm) -02 .3125 24U

25、NS-3A .3023 (7.678) - .3095 (7.861) .2797 (7.104) - .2824 (7.173) .2584 (6.563) -03 .375 24UNS-3A .3648 (9.266) - .3720 (9.449) .3420 (8.687) - .3449 (8.760) .3209 (8.151) -04 .4375 20UNS-3A .4264 (10.831) - .4345 (11.036) .3989 (10.132) - .4020 (10.211) .3732 (9.479) -05 .500 20UNS-3A .4889 (12.418

26、) - .4970 (12.623) .4613 (11.717) - .4645 (11.80) .4357 (11.067) -06 .5625 18UNS-3A .5508 (13.990) - .5595 (14.211) .5200 (13.208) - .5234 (13.294) .4913 (12.479) -07 .625 18UNS-3A .6133 (15.578) - .6220 (15.799) .5824 (14.793) - .5859 (14.881) .5538 (14.067) -08 .750 16UNS-3A .7376 (18.735) - .7470

27、 (18.974) .7026 (17.846) - .7064 (17.942) .6703 (17.026) -09 .8125 16UNS-3A .8001 (20.323) - .8095 (20.561) .7653 (19.44) - .7689 (19.530) .7328 (18.613) -10 .875 14UNS-3A .8617 (21.887) - .8720 (22.149) .8215 (20.866) - .8256 (20.970) .7844 (19.924) -11 1.000 12UNS-3A .9856 (25.034) - .9970 (25.324

28、) .9385 (23.838) - .9429 (23.950) .8948 (22.728) -12 1.0625 12UNS-3A 1.0481 (26.622) - 1.0595 (26.911) 1.0012 (25.430) - 1.0054 (25.537) .9573 (24.315) -14 1.1875 12UNS-3A 1.1731 (29.797) - 1.1845 (30.086) 1.1261 (28.603) - 1.1304 (28.712) 1.0823 (27.490) -16 1.3125 12UNS-3A 1.2981 (32.972) - 1.3095

29、 (33.261) 1.2511 (31.778) - 1.2554 (31.887) 1.2073 (30.665) -18 1.500 12UNS-3A 1.4856 (37.734) - 1.4970 (38.024) 1.4381 (36.528) - 1.4429 (36.650) 1.3948 (35.428) -20 1.625 12UNS-3A 1.6106 (40.909) - 1.6220 (41.199) 1.5635 (39.713) - 1.5679 (39.825) 1.5198 (38.603) -24 1.875 12UNS-3A 1.8606 (47.259)

30、 - 1.8720 (47.549) 1.8134 (46.060) - 1.8179 (46.175) 1.7698 (44.953) -28 2.250 12UNS-3A 2.2356 (56.784) - 2.2470 (57.074) 2.1884 (55.585) - 2.1929 (55.700) 2.1448 (54.478) -32 2.500 12UNS-3A 2.4856 (63.134) - 2.4970 (63.424) 2.4429 (62.050) - 2.4383 (61.933) 2.3948 (60.828) FIGURE 1. Elbow, tube, bo

31、ss, 90 - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS9194C 8 Dash number U radius inches (mm) V inches (mm) W inches (mm) X inches (mm) Y inches (mm) .010 (0.25) -02 .062 (1.57) .250 (6.35) .300 (7.62) .200 (5.08) .722 (18.34) -03 .0

32、62 (1.57) .312 (7.92) .310 (7.87) .220 (5.59) .795 (20.19) -04 .062 (1.57) .375 (9.53) .380 (9.65) .260 (6.60) .862 (21.89) -05 .062 (1.57) .438 (11.13) .440 (11.18) .300 (7.62) .907 (23.04) -06 .094 (2.39) .500 (12.70) .490 (12.45) .330 (8.38) 1.013 (25.73) -07 .094 (2.39) .562 (14.27) .490 (12.45)

33、 .330 (8.38) 1.032 (26.21) -08 .094 (2.39) .688 (17.48) .640 (16.26) .430 (10.92) 1.257 (31.93) -09 .094 (2.39) .750 (19.05) .660 (16.76) .440 (11.18) 1.257 (31.93) -10 .094 (2.39) .812 (20.62) .750 (19.05) .500 (12.70) 1.473 (37.41) -11 .094 (2.39) .938 (23.83) .750 (19.05) .500 (12.70) 1.677 (42.6

34、0) -12 .094 (2.39) 1.000 (25.40) .750 (19.05) .500 (12.70) 1.677 (42.60) -14 .125 (3.18) 1.125 (28.58) .750 (19.05) .500 (12.70) 1.893 (48.08) -16 .125 (3.18) 1.250 (31.75) .750 (19.05) .500 (12.70) 1.903 (48.34) -18 .125 (3.18) 1.438 (36.53) .900 (22.86) .600 (15.24) 2.152 (54.66) -20 .125 (3.18) 1

35、.625 (41.28) .900 (22.86) .600 (15.24) 2.152 (54.66) -24 .125 (3.18) 1.812 (46.02) .900 (22.86) .600 (15.24) 2.418 (61.42) -28 .188 (4.78) 2.188 (55.58) .900 (22.86) .660 (16.76) 2.902 (73.71) -32 .250 (6.35) 2.438 (61.93) 1.125 (28.58) .750 (19.05) 3.152 (80.06) FIGURE 1. Elbow, tube, boss, 90 - Co

36、ntinued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS9194C 9 Dash number Z inches (mm) .010 (0.25) Approx weight lbs/ea (grams/ea) -02 1.018 (25.86) .025 (11) -03 1.033 (26.24) .036 (16) -04 1.146 (29.11) .050 (23) -05 1.171 (29.74) .065 (29) -

37、06 1.301 (33.05) .083 (38) -07 1.336 (33.93) .097 (44) -08 1.523 (38.68) .186 (84) -09 1.553 (39.45) .215 (98) -10 1.743 (44.27) .280 (127) -11 1.918 (48.72) .408 (185) -12 1.948 (49.48) .445 (202) -14 2.070 (52.58) .538 (244) -16 2.135 (54.23) .644 (292) -18 2.225 (56.52) .954 (433) -20 2.290 (58.1

38、7) 1.087 (493) -24 2.145 (54.48) 1.436 (651) -28 2.750 (69.85) 2.612 (1185) -32 3.100 (78.74) 3.382 (1534) NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for information only. 3. Unless otherwise specified tolerances for linear dimensions are .015 inch (0.38 mm) and angular dime

39、nsions are 5, all dimensions concentric within .010 inch (0.25 mm) FIM. 4. Unless otherwise specified machined surfaces to be 125 inches (3.18m) in accordance with ASME B46.1. 5. Diameter F shall be free of thread marks. 6. Diameter F shall be concentric with PD of thread within .0025 inch (1.134 mm

40、) FIM. 7. Lettering height: For -02 through -04 size: .020 - .040 inch (0.51 - 1.02 mm). For size -05 through -16: .040 - .060 inch (1.02 - 1.52 mm). For size -18 and larger: .090 - .150 inch (2.29 - 3.81 mm). 8. All diameters shall be concentric within .010 inch (0.25 mm) FIM unless otherwise speci

41、fied. 9. Parting line mismatch .015 inch (0.38 mm) max. 10. E minimum wall thickness between forged surface and hole A. 11. Unless otherwise specified break sharp edges .003 - .015 inches (0.08 - 0.38 mm). 12. Dimensions are to sharp corners unless otherwise specified. 13. Threads shall be in accord

42、ance with FED-STD-H28/2. FIGURE 1. Elbow, tube, boss, 90 - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS9194C 10 REQUIREMENTS: Dimensions and configurations: See figure 1. Material: Steel, corrosion and heat-resistant in accordance wi

43、th SAE-AMS5646. Max operating temperature: Oxidation resistance up to 1500F (816C). Max operating pressure: 1500 psi (10MPa). Finish: Passivate in accordance with SAE-AMS2700, method 1. All parts shall be fluorescent penetrant inspected in accordance with ASTM E1417. PIN: MS9194 -08 PIN Example: MS9

44、194-08 identifies a 90 elbow .500 inch (tube), CRES. Do not use unassigned PINs. Intended usage: Jet engine, miscellaneous parts, oil, fuel, and de-icing kits. Not to be used on hydraulic, oxygen or applications requiring pressures of 3000 psi (21 MPa). Changes from previous issue. Marginal notation

45、s are not used in this revision to identify changes with respect to the previous issue due to the extent of the changes. Referenced documents. In addition to SAE-AS4841, this document references the following: FED-STD-H28/2 ASTM E1417 ASME B46.1 SAE-AS478 SAE-AMS2700 SAE-AMS5646 Specification sheet

46、number Elbow size (see figure 1) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS9194C 11 CONCLUDING MATERIAL Custodians: Preparing activity: Navy - AS DLA - CC DLA - CC (Project 4730-2009-080) Review activity: Navy - SA NOTE: The activities listed

47、 above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-