DLA MS24285 REV D-2005 CONNECTORS ELECTRICAL STYLE S RACK AND PANEL MINIATURE《S型机架和小组微型电器连接器》.pdf

1、INCH-POUNDMS24285D 14 July 2005 SUPERSEDING MS24285C 6 May 1968 DETAIL SPECIFICATION SHEET CONNECTORS, ELECTRICAL, STYLE S, RACK AND PANEL, MINIATURE Inactive for new design after 8 June 1999. This specification is approved for use by all Departments and Agencies of the Department of Defense. The re

2、quirements for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-26518. The Qualified Products List (QPL) associated with this inactive for new design specification will be maintained until acquisition of the product is no longer required, where upon the sp

3、ecification and QPL will be canceled. Style S (socket insert) FIGURE 1. Connector dimensions and configurations.AMSC N/A FSC 5935 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS24285D 2 Environment Resistant (R) Receptacles Shell size D .005 E .00

4、4 F .005 G H .005 A 4.296 3.875 3.239 3.147 3.061 B 2.866 2.445 1.809 1.717 1.631 C 2.421 2.000 1.380 2.888 1.202 FIGURE 1. Connector dimensions and configurations - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS24285D 3 Inches mm Inch

5、es mm Inches mm .015 .018 .019 .022 .025 .035 .066 .075 .085 .091 .093 .101 .109 .117 .121 .132 .148 .155 0.38 0.46 0.48 0.56 0.64 0.89 1.68 1.87 2.16 2.31 2.36 2.57 2.77 2.97 3.07 3.35 3.76 3.94 .161 .177 .185 .207 .211 .250 .253 .257 .280 .285 .313 .321 .385 .541 .551 .689 .775 .867 .998 4.09 4.50

6、 4.70 5.26 5.36 6.35 6.43 6.53 7.11 7.24 7.95 8.15 9.78 13.74 14.00 17.50 19.69 22.02 25.35 1.008 1.178 1.198 1.202 1.250 1.380 1.631 1.717 1.809 2.000 2.421 2.445 2.866 2.888 3.061 3.147 3.239 3.875 4.296 25.60 29.92 30.43 30.53 31.75 35.05 41.43 43.61 45.95 50.80 61.49 62.10 72.80 73.36 77.75 79.9

7、3 82.27 98.43 109.12 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for information only. 3. Unless otherwise specified tolerances are .003 inch (0.08 mm). 4. For insert arrangements see MS24288. 5. Dimension on socket contact location applies when contacts are placed in inserts

8、 for inspection or application. FIGURE 1. Connector dimensions and configurations - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS24285D 4 REQUIREMENTS: Dimensions and configuration see figure 1. Materials shall be in accordance with M

9、IL-DTL-26518. For mating details, see MS24287 and MS24288. Part or Identifying Number (PIN): Basic specification numberMS prefix Environmental resisting MS 24285 R A3 Shell size and insert designator (see figure 1 and MS24288) Referenced documents: In addition to MIL-DTL-26518 this document referenc

10、es the following: MS24287 MS24288 Changes from previous issue. Marginal notations are not used in this revision to identify changes with respect to the previous issue due to the extent of the changes. CONCLUDING MATERIAL Custodians: Preparing activity:Air Force - 11 DLA - CC DLA - CC (Project 5935-4

11、695-000) Review activities: DLA-IS NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-