DLA MS25024 REV H-2012 RELAY 10 AMP 4PDT SEALED CLASS O [Use DLA MS24568 REV K VALID NOTICE 1 DLA MS24568 REV K (1) DLA MS24568 REV K DLA MS24568 REV J (2) DLA MS24568 REV J (1) DL.pdf

1、 AMSC N/A FSC 5945 MS25024H 28 February 2012 SUPERSEDING MS25024G 15 December 2001 DETAIL SPECIFICATION SHEET RELAY, 10 AMP, 4PDT, SEALED, CLASS O Inactive for new design after 12 August 1964. For new design, use in MS24568 dash number D1. This specification is approved for use by all Departments an

2、d Agencies of the Department of Defense. The requirements for acquiring the relay described herein shall consist of this specification sheet and in MIL-PRF-6106. FIGURE 1. Configurations and dimensions. INCH-POUND Provided by IHSNot for ResaleNo reproduction or networking permitted without license f

3、rom IHS-,-,-MS25024H 2 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only. 3. Unless otherwise specified, tolerance are .010 (0.025 mm). FIGURE 1. Configurations and dimensions - Continued. REQUIREMENTS Operating cycles: 50,000 minimum. Contact data: Con

4、tact voltage drop: Initial: 0.150 volt maximum. After life: 0.175 volt maximum. Load ratings: See table I. TABLE I - Rated contact load (per pole). Type of load Amperes Resistive (dc) 10 Resistive (ac 400 Hz, 115 volts) 10 Inductive 10Motor 6 Mixed loads MS25024-2 See MIL-PRF-6106. Overload current:

5、 See MIL-PRF-6106. Inches mm .005 0.013 .010 0.025 .060 0.152 .562 1.427 .750 4.044 1.000 2.540 1.250 3.175 2.625 6.668 2.687 6.825 2.937 7.460 3.312 8.412 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS25024H 3 Rupture current: See MIL-PRF-6106.

6、Coil data: Nominal coil voltage: 28 volts. Maximum operating voltage: 29 volts. Pickup voltage: 18 volts. Hold voltage: 7 volts. Dropout voltage: 1.5 volts. Rated duty: Continuous. Coil current: 0.35 amperes, maximum. Physical data: Weight: 0.8 pounds, maximum. Qualification by similarity: See MIL-P

7、RF-6106. Retention of qualification: To retain qualification, the manufacturer shall submit group A acceptance reports on a yearly basis to the qualifying activity. Conformance inspection: Performance of groups B and C tests are not applicable. Part or Identifying Number (PIN): MS25024-2. Supersessi

8、on information: Interchangeability relationship: MS25024 parts are functionally interchangeable in accordance with MS24568 Dash Number D1 parts. MS25024 parts are dimensionally interchangeable in accordance with MS24568 Dash Number D1 parts in most cases but not in all cases. Dimensional interchange

9、ability is determined by the installation and a determination must be made for each different installation. Part MS25024-2 supersedes MS25024-1. Changes from previous issue. The margins of this specification are marked with vertical lines to indicate where changes from the previous issue were made.

10、This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations and relationship to t

11、he last previous issue. Referenced documents. In addition to MS25024, this document references the following: MIL-PRF-6106 MS24568 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS25024H 4 Custodian: Preparing activity: Army - CR DLA - CC Navy - AS

12、Air Force - 85 DLA - CC Review activity: (Project 5945-2012-002) Air Force 99 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.daps.dla.mil/. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-