DLA MS25455 REV H-2003 RELAYS ELECTROMAGNETIC 5 AMPERES 2 PDT TYPE I MAGNETIC LATCH SOCKET MOUNTED HERMETICALLY SEALED《I型2 PDT 5安培火箭安装磁力锁密封电磁继电器》.pdf

1、 AMSC N/A 1 of 5 FSC 5945 INCH-POUND MS25455H 27 November 2003 SUPERSEDING MS25455G 20 Jan 1989 DETAIL SPECIFICATION SHEET RELAYS, ELECTROMAGNETIC, 5 AMPERES, 2 PDT, TYPE I, MAGNETIC LATCH, SOCKET MOUNTED HERMETICALLY SEALED INACTIVE FOR NEW DESIGN AFTER 5 JUN 1987. NO SUPERSEDING SPECIFICATION This

2、 specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the relay described herein shall consist of this specification and the latest issue of MIL-PRF-6106. FIGURE 1. Dimensions and configurations. Provided by IHSNot for ResaleN

3、o reproduction or networking permitted without license from IHS-,-,-MS25455H 2 NOTES: 1/ Dimensions are in inches. 2/ Metric equivalents are given for general information only. 3/ Unless otherwise specified, tolerance is .010 (0.25 mm). 4/ Terminal numbers need not appear on relay header provided th

4、ere is affixed to the relay a suitable legible circuit diagram that permanently and positively identifies each terminal location specified hereon. 5/ The use of diodes on ac relays is optional. Actual application must be shown on label. 6/ Pins to be perpendicular to header surface within 1 degree.

5、7/ Relay is magnetically latched in both positions. Caution note to observe polarity must appear on relays with dc coils. 8/ Shock, vibration, and acceleration requirements applicable with coils de-energized. 9/ In the event of conflict between the text of this specification and the references cited

6、 herein, the text of this specification shall take precedence. 10/ Referenced Government documents of the issue listed in that issue of the Department of Defense Index of Specifications and Standards (DoDISS) specified in the solicitation forms a part of this specification to the extent specified he

7、rein. 11/ Socket pin terminals shall provide the operational, environmental, and interface characteristics to provide a reliable interconnect to gold-plated contacts. Terminals shall be gold plated. One system for gold plating that may be used is ASTM B488, type 3, class 1.25 with a nickel underplat

8、e of 50 to 150 microinches thick. The gold plating system shall enable the product to meet the performance requirements of this specification and shall be approved by the qualifying activity. 12/ Gasket shall provide a reliable seal between the relay and mating socket that will meet the environmenta

9、l, operational, and interface requirements of the relay with the mating socket. The gasket shall have thickness .075, recessed .047 in to bracket. Gasket material according to AMS 3332 has been considered acceptable. FIGURE 1. Dimensions and configurations - Continued. Inches mm Inches mm .001 0.03

10、.165 4.19 .005 0.13 .203 5.16 .010 0.25 .253 6.43 .040 1.02 .304 7.72 .047 1.19 .330 8.38 .062 1.57 .344 8.74 .075 1.91 .456 11.58 .077 1.96 .608 15.44 .093 2.36 .700 17.78 .143 3.63 1.500 38.10 .147 3.73 1.750 44.45 .152 3.86 1.844 46.84 2.187 55.55 CIRCUIT D1SEE NOTE 7CIRCUIT A1SEE NOTE 5CIRCUIT A

11、D1SEE NOTE 5,7Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS25455H 3 TABLE I. Dash numbers and characteristics. Dash number MS25455- Type Coil Terminal type Max weight in pounds D1 I dc Plug in 0.21 A1 I ac Plug in 0.23 AD1 I ac-dc Plug in 0.23 T

12、ABLE II. Operating characteristics. Coil data Time - milliseconds maximum Nominal Max 1/ Max pick-up voltage Contact Bounce Main Aux PIN MS25455- Coil Volts 1/ Freq Hz Res Volts Amp Nor- mal 2/ High temptest Cont cur-rent test Op-erate 3/ Rel-ease 4/ NO NC NO NC D1 X1, X2 Y1, Y2 28 dc N/A 29 0.12 18

13、 18 19.8 25 N/A 2 2 N/A N/A A1 X1, X2 Y1, Y2 115 400 5/ N/A 122 0.06 90 90 95 25 N/A 2 2 N/A N/A X1, X2 115 400 5/ N/A 122 0.06 90 90 95 25 N/A 2 2 N/A N/A AD1 Y1, Y2 28 dc N/A 29 0.12 18 18 19.8 25 N/A 2 2 N/A N/A 1/ CAUTION: Use of any coil voltage less than nominal coil voltage will compromise th

14、e operation of the relay. 2/ Over the temperature range. 3/ With nominal coil voltage. 4/ From nominal coil voltage. 5/ MS25455-A1 and -AD1 ac coils may be used on 60 Hz if maximum ambient temperature is limited to +85C (coil current: 0.066 ampere maximum). TABLE III. Rated contact load (amperes per

15、 pole) (case grounded). 28 V dc 115 V ac, 1 phase 115/200 V ac, 3 phase 1/ Main Aux Main Aux Main Aux Type of load Life operating cycles x 103NO NC NO NC 400 Hz 60 Hz 400 Hz 60 Hz 400 Hz 60 Hz 400 Hz 60 Hz See appropriate notes Resistive 100 5 5 5 4 Inductive 100 Inductive 20 3 3 3 2 Motor 100 1.5 1

16、.5 1.5 1 Lamp 100 0.8 0.8 0.8 0.6 Transfer load 2/ Mechanical life reduced current 400 1.25 1.25 1.25 1 Mixed loads Applicable per specification 1/ Absence of value indicates relay is not rated for 3-phase application. 2/ Transfer load indicates relay is suitable for transfer between unsynchronized

17、ac power supplies at rating indicated. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS25455H 4 Environmental characteristics. Temperature range -70C to +125C Max altitude rating 80,000 ft Shock G-level 50 gs Duration 11 ms Max duration contact ope

18、ning 10 s Vibration - sinusoidal (see chart below) G-level 10 gs Frequency range 5-1,500 Hz Acceleration 15 gs Electrical characteristics. Insulation resistance: Initial: 100 megohms. After life or environmental tests: 50 megohms. Dielectric strength (sea level). Initial After life tests Coil to cas

19、e 1,000 V rms 1,000 V rms Aux contacts All other points 1,000 V rms 1,000 V rms Dielectric strength (altitude). (When mounted in mating socket 80,000 ft Coil to case 500 V rms Aux contacts All other points 500 V rms Max contact voltage drop: Initial: 0.150 volt. After life test: 0.175 volt. Overload

20、 current 20 amperes. Rupture current 25 amperes. Duty rating Continuous. RFI specification MIL-STD-461 (Applicable to coil circuits of ac operated relays).Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS25455H 5 Conformance inspection. Performance

21、of groups B and C tests are not applicable. Group A acceptance reports shall be submitted to the preparing activity on a yearly basis in order to retain qualification for this military specification sheet. Qualification by similarity: See MIL-PRF-6106. NOTES Referenced documents. In addition to MIL-

22、PRF-6106, this specification sheet references the following documents. (Government documents are available on line at http:/assist.daps.dla.mil/quicksearch or www.dodssp.daps.mil or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094). Society o

23、f Automotive Engineers documents are available from the Society of Automotive Engineers 400 Commonwealth Drive Warrendale, Pennsylvania, United States, 15096-0001. http:/www.sae.org STANDARDS Department of Defense MIL-STD-461 - Requirements for the Control of Electromagnetic Interference Characteris

24、tics of Subsystems and Equipment Society of Automotive Engineers (SAE) SAE-AMS3332 - Silicone Rubber Extreme Low-Temperature Resistant, 15-30 Custodians: Preparing activity:Navy - AS DLA - CC Air Force - 11 DLA - CC (Project 5945-1221-11) Review activities: Navy - EC NOTE: The activities listed abov

25、e were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using ASSIST Online database at www.dodssp.daps.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-