DLA MS27087 REV D-2013 ELBOW NIPPLE END FLARED TUBE TO HOSE - 45 SWIVEL NUT.pdf

1、 AMSC N/A FSC 4730 MS27087D 1 May 2013 SUPERSEDING MS27087C 25 September 2003 DETAIL SPECIFICATION SHEET ELBOW, NIPPLE END, FLARED, TUBE TO HOSE - 45 SWIVEL NUT This specification sheet is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring t

2、he product described herein shall consist of this specification sheet and MIL-DTL-27272. FIGURE 1. Elbow illustration. INCH-POUND Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS27087D 2 FIGURE 1. Elbow illustration - Continued. Provided by IHSNot

3、for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS27087D 3 Size and material code A min (see note 1) C D +.005 -.000 F G +.005 -.000 H .005 J +.005 -.000 CRES Al -3/-4C - .515 .106 .010 .307 .288 +.005 -.000 .205 .295 .373 -4C - -5C - .520 .116 .322 .316 .268 .360 .416

4、 -6C - .555 .391 .330 .425 .491 -8C -8D .630 .140 .020 .335 .497 .426 .530 .616 -10C -10D .654 .098 +.004 -.000 - .586 .526 .625 .706 -12C -12D .755 .128 +.005 -.000 - .674 .650 .760 .826 -16C -16D .831 - 1.001 +.008 -.000 .900 1.040 1.150 -20C -20D .881 - 1.255 +.005 1.151 1.275 1.405 -24C -24D 1.0

5、35 - 1.490 -.000 1.401 1.550 1.635 Size and material code K L .004 M min (see note 1) N P Q max S CRES Al Steel Alum -3/-4C - .015 +.005 -.000 .036 .485 .161 - +.005 -.000 1.078 .020 - .480 .010 -4C - 1.117 - -5C - .040 .501 .224 1.150 - -6C - .521 .261 1.224 - -8C -8D .020 .047 .583 .345 .345 +.006

6、 -.000 1.720 - .600 -10C -10D .005 - .620 .440 .440 1.486 .035 - .650 .015 -12C -12D .030 - .720 .560 .560 1.937 15.5 .675 .025 -16C -16D - .796 .828 .828 1.993 10.5 .730 -20C -20D - .846 1.058 1.058 2.252 15.5 .935 -24C -24D .035 - 1.000 1.253 1.282 +.005 -.000 2.561 .980 FIGURE 1. Elbow illustrati

7、on - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS27087D 4 Size and material code T max U V W +.005 -.000 CRES Al CRES Al -3/-4C - - .283 .020 - - - - -4C - - .322 - - - - -5C - - .340 - - - - -6C - - .389 - - - - -8C -8D - .465 - - -

8、 - -10C -10D - .536 .035 - - .420 .427 -12C -12D .900 .623 .625 .010 .500 .500 -16C -16D 1.190 .660 .670 .545 .545 -20C -20D 1.485 .768 .695 .565 .571 -24C -24D 1.750 .867 .795 .665 .665 NOTES: 1. Use A dimension when the adjacent diameter to the left of plane B-B is greater than J dimension. When t

9、he adjacent diameter is equal to or less than J dimension, M dimension may be used in place of A dimension. 2. Any design of the elbow to the left of plane B-B is acceptable provided the dimensions P and U and the requirements of this specification sheet and the procurement specification are met. 3.

10、 Any forged design is acceptable for -3/-4 through -8 size. 4. Any bent tube design is acceptable for -10 through -24 size. The inside diameter (ID) of the elbow for the -10 through -24 sizes shall not be less than the ID of the nipple end of the adapter. 5. Ovality shall not exceed 7.5 percent of n

11、ominal tubing OD. 6. Unless otherwise specified, break or radius all corners .005, +.005, -.000 inch. 7. All diameters within length A plus S must be concentric within .005 inch total indicator movement. 8. Unless otherwise specified, maximum surface roughness shall not exceed 125 in. Ra in accordan

12、ce with ASME B46.1. 9. Remove all burrs and slivers. FIGURE 1. Elbow illustration - Continued. REQUIREMENTS Elbow illustration, see figure 1. Intended use. This part is a component of MS27067 for sizes -3/-4 through -8, and MS27063 for sizes -10 through -24. This is a design standard for manufacturi

13、ng purposes. The item is only procured as an integral part of adapter assemblies. Materials. Material and material codes see table I. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS27087D 5 TABLE I. Materials and material codes. Material code Mate

14、rial C CRES, class 304 or 321 cold drawn or cold rolled, in accordance with SAE-AMS-QQ-S-763, SAE-AMS5639 or SAE-AMS5645. D Aluminum alloy, 6061-T6 or T651, in accordance with SAE-AMS-QQ-A-367, SAE-AMS-4117 or alloy 7075-T73, 7075-T7351 in accordance with SAE-AMS-QQ-A-225/9 or alloy 7055-T7351 in ac

15、cordance with SAE-AMS-4124. Finish. Corrosion-resistant steel, passivate in accordance with SAE-AMS2700, method 1, type 6 or 7. Aluminum alloy. Anodize in accordance with MIL-A-8625, type II, dye blue. NOTE: Avoid using graphite dry film lubes with aluminum nipples because in a wet environment, grap

16、hite becomes corrosive to aluminum. Dry-film lubrication. Dry film lubricant in accordance with figure 2 and table II. Size and material code B min E CRES Al -3/-4C - .870 .25 .05 -4C - -5C - .890 -6C - -8C -8D 1.030 .32 .12 -10C -10D 1.130 .35 .15 -12C -12D 1.240 -16C -16D 1.340 .39 .19 -20C -20D 1

17、.570 .48 .28 -24C -24D 1.720 .50 .30 FIGURE 2. Dry-film lubrication area. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS27087D 6 TABLE II. Dry film designator. Dry film designator SAE class or type designator Dry film characteristics Blank Any SA

18、E class or type below N/A SAE-AS1701 SAE-AS1701 class SAE-AS1701 temperature ranges F (C) 4 4 -65 to +1400F (-54 to 760C) 5 5 -65 to +850F (-54 to 454C) 6 6 -375 to +850F (-226 to 454C) SAE-AS5272 SAE-AS5272 type SAE-AS5272 temperature ranges. F (C) 7 Type I -90 to 400F (-68 to 204C) endurance life

19、of 250 min minimum 8 Type II -90 to 400F (-68 to 204C) endurance life of 450 min minimum 9 Type III Color 1 - Natural product color -90 to 400F (-68 to 204C) low Volatile organic compound with an endurance life of 450 min minimum 10 Type III Color 2 - Black color -90 to 400F (-68 to 204C) low Volati

20、le organic compound with an endurance life of 450 min minimum Dry film designator MIL classification Dry film characteristics MIL-PRF-46010 1/ - MIL-PRF-46010 temperature ranges. F (C) 11 1 Color 1 natural product color, -90 to 400F ( -68 to 204C) solvent resisting 12 2 Color 2 - Black color -90 to

21、400F ( -68 to 204C) solvent resisting 1/ Not for aerospace usage. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS27087D 7 Part or Identifying Number (PIN): The PIN consists of prefix “MS,” the specification sheet number, dash number for 45 elbow,

22、nipple end size, letter for material, and a blank or number for dry film lubricant. Unassigned PINs shall not be used. MS 27087 -10 C 4 PIN examples: MS27087-10C indicates a 45 elbow, nipple end size 10, CRES with dry film class designator. MS27087-10C4 indicates a 45 elbow, nipple end size 10, CRES

23、 with dry film class designator 4. Order of precedence. Unless otherwise noted herein or in the contract, in the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes applicable

24、 laws and regulations unless a specific exemption has been obtained. Referenced documents shall be of the issue in effect on date of invitations for bid. Changes from previous issue. Marginal notations are not used in this revision to identify changes with respect to the previous issue, due to the e

25、xtent of the changes. Referenced documents. In addition to MIL-DTL-27272, this document references the following: MIL-A-8625 MIL-PRF-46010 MS27063 MS27067 ASME B46.1 SAE-AMS-QQ-A-225/9 SAE-AMS-QQ-A-367 SAE-AMS-QQ-S-763 SAE-AMS2700 SAE-AMS-4117 SAE-AMS-4124 SAE-AMS5639 SAE-AMS5645 SAE-AS1701 SAE-AS43

26、95 SAE AS5272 Specification sheet number MS prefix Material code letter (see table I) Size code number (see figure 1) Dry film designator (see table II) CRES only Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS27087D 8 CONCLUDING MATERIAL Custodia

27、ns: Preparing activity: Army - AV DLA - CC Navy - AS Air Force - 99 (Project 4730-2013-035) DLA - CC Review activities: Army - AR, AT, MI Navy - MC, SA, SH Air Force - 71 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-