DLA MS27144 REV C-2003 CONNECTOR PLUG ELECTRICAL SOCKET CONTACT NO 14 AND 16 AWG WATERPROOF《14 16 AWG防水插座接触插头连接器》.pdf

1、MS27144C 17 June 2003 SUPERSEDING MS27144B 16 February 1988 DETAIL SPECIFICATION SHEET CONNECTOR, PLUG, ELECTRICAL, SOCKET CONTACT, NO. 14 AND 16 AWG, WATERPROOF This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the pr

2、oduct described herein shall consist of this specification. FIGURE 1. Configuration and dimensions. AMSC N/A 1 of 3 FSC 5935 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited.INCH-POUND Provided by IHSNot for ResaleNo reproduction or networking permitted without licens

3、e from IHS-,-,-MS27144C 2 Inches mm Inches mm .002 .003 .010 .015 .045 .125 .130 .05 .07 .25 .38 1.10 3.18 3.30 .152 .160 .245 .494 .690 1.390 3.86 4.06 6.22 12.55 17.50 35.30 MS dash no. Reference drawing no. (assembly) Style Size Wire gage Shell number Terminal number Sleeve number Cable dia Cable

4、 MIL-DTL-13486 PIN -1 8338560 1 1 14 8338561 8338564 .160.010 M13486/1-5 -2 None 1 2 16 8724494 OR 8338562 .130.015 M13486/1-3 -3 7982398 2 1 14 7982401 7982997 .160.010 M13486/1-5 FIGURE 1. Configuration and dimensions - Continued. REQUIREMENTS: Material: Shell: Rubber in accordance with ASTM D2000

5、, M3BC610A14C12EO34F19. Terminal: Brass composition, temper half hard minimum in accordance with ASTM B 36/B 36M, ASTM B 121/B 121M or ASTM B124/B 124M. Terminal protective finish: Silver plate, grade D, class S, .0002-inch minimum thickness in accordance with ASTM B700. Mating connectors: Style 1 s

6、ize 1 mates with connector MS33800 and MS27142, size 2. Style 1 size 2 mates with connector MS33800 and MS27142, size 3. Style 2 size 1 to be used only with ribbed receptacle MS33800, style II to denote polarity. When connectors are coupled, the following requirements shall apply: Voltage drop: The

7、voltage drop shall not exceed 20 millivolts and shall meet the requirements outlined in MIL-STD-202, method 307. Dielectric strength: The assembly shall withstand dielectric strength test of 1000 volts, and meet the requirements of MIL-STD-202, method 302. Waterproof requirements: The assembly shall

8、 be waterproof. Refer to MIL-HDBK-1184, or equivalent, for guidance on waterproof testing. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS27144C 3 Salt spray corrosion test: The assembly shall meet the requirements of salt spray corrosion test out

9、lined in MIL-STD-202, method 101 (5% saline solution, 200 hours duration). Pull test: Terminal number 8338564 to be crimped to cable. Terminal number 7982997 to be soldered to cable with solder composition SN-50 or SN-60, in accordance with J-STD-004, J-STD-005, and J-STD-006. The terminal shall wit

10、hstand a pull test of 40 pounds (18 kilograms) for style 1 size 2, or 60 pounds (27 kilograms) for style 1 size 1, and style 2 size 1. Separation force: The force required to uncouple the connectors shall not exceed 50 percent of the values expressed in the pull test above when tested at -55C and at

11、 85C. Part or Identifying Number (PIN): MS27144- (dash number as shown on figure 1). Reference drawings may be obtained from the U.S. Army Tank Automotive Command, Warren, MI., 48397-5000. (Marginal notations are not used in this revision to identify changes with respect to the previous issue due to the extent of the changes.) CONCLUDING MATERIAL Custodians: Preparing activity: Army AT DLA - CC Air Force 11 Navy MC (Project 5935-4427-003) DLA - CC Review activities: Army CR, CR4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-