1、 INCH-POUNDMS27229B 14 May 2007 SUPERSEDING MS27229A 22 September 2000 DETAIL SPECIFICATION SHEET FLANGE NIPPLE ASSEMBLY 45, ADAPTER, HOSE TO TUBE, REUSABLE, HYDRAULIC, FUEL AND OIL LINES This specification is approved for use by all Departments and Agencies of the Department of Defense. The require
2、ments for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-5070. FIGURE 1. 45 flange nipple assembly dimensions and configuration. AMSC N/A FSC 4730 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS27229B
3、2 C Elbow PIN D Nipple PIN E Shoulder PIN Dash number A .035 inches (mm) B .035 inches (mm) MS27235 MS27239 MS27237 F (ref) inches (mm) -8 .921 (23.39) .338 (8.59) -8 -8 -8 .50 (12.70) -10 1.009 (25.63) .375 (9.53) -10 -10 -10 .62 (15.75) -12 1.194 (30.33) .468 (11.89) -12 -12 -12 .84 (21.34) -16 1.
4、282 (32.56) .505 (12.83) -16 -16 -16 .97 (24.64) -20 1.561 (39.65) .569 (14.45) -20 -20 -20 1.19 (30.23) -24 1.756 (44.60) .624 (15.85) -24 -24 -24 1.38 (35.05) -32 2.084 (52.93) .734 (18.64) -32 -32 -32 1.75 (44.45) -40 2.430 (61.72) .825 (20.96) -40 -40 -40 2.06 (52.32) -48 2.732 (69.39) .898 (22.
5、81) -48 -48 -48 2.31 (58.67) NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for information only. 3. Part or Identifying Number (PIN). FIGURE 1. 45 flange nipple assembly dimensions and configuration - Continued. REQUIREMENTS: Dimensions and configurations: The design, construct
6、ion, and physical dimensions shall be in accordance with MIL-DTL-5070 and figure 1 in case of conflict between this drawing and MIL-DTL-5070, this drawing shall govern. Intended use. This part is a component of MS27230. Material: Aluminum shall be in accordance with MIL-DTL-5070. Braze: Braze along
7、joint J (see figure 1) in accordance with SAE-AMS2672. Heat treatment: Heat treat in accordance with SAE-AMS-H-6088, condition T6, after braze. Finish: Finish in accordance with MIL-DTL-5070 Color identification: Color identification shall be in accordance with MIL-DTL-5070. Provided by IHSNot for R
8、esaleNo reproduction or networking permitted without license from IHS-,-,-MS27229B 3 PIN example: MS 27229 -8 AA Aluminum - anodic coating Dash number from figure 1 Basic specification number Identification of product. The PIN and the manufacturers Commercial and Government Entity (CAGE) Code or tra
9、demark shall be permanently marked on the assembly, see figure 1, or on a removable tag securely attached to the assembly. MS prefix Changes from previous issue. Marginal notations are not used in this revision to identify changes with respect to the previous issue, due to the extent of the changes.
10、 Referenced documents. In addition to MIL-DTL-5070, this document references the following: MS27230 MS27235 MS27237 MS27239 SAE-AMS-H-6088 SAE-AMS2672 CONCLUDING MATERIAL Custodians: Preparing activity:Army - AT DLA - CC Navy - AS Air Force - 99 (Project 4730-2005-048) DLA - CC Review activities: Ar
11、my - AV Navy - MC, SA Air Force - 11, 71 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
备案/许可证编号:苏ICP备17064731号-1