DLA MS27235 REV D-2007 ELBOW TUBE 45 DEG 《45度弯管》.pdf

1、 MS27235D INCH-POUND14 May 2007 SUPERSEDING MS27235C 22 September 2000 DETAIL SPECIFICATION SHEET ELBOW TUBE, 45 This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this spec

2、ification sheet and MIL-DTL-5070. FIGURE 1. Elbow dimensions and configuration. AMSC N/A Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-FSC 4730 MS27235D 2 Dash number A .015 (0.38) inches (mm) B .015 (0.38) inches (mm) C +.031 (0.79) -.000 inches (

3、mm) D Dia .005 (0.13) inches (mm) (see note 5)E Rad .060 (1.52) inches (mm) Ttube wall thickness inches (mm) X inches (mm)(see note 6)-4 .531 (13.49) .220 (5.59) .245 (6.22) .375 (9.53) .035 (.89) .010 (.25) -5 .575 (14.61) .238 (6.05) .307 (7.80) .438 (11.13) .012 (.30) -6 .370 (9.40).049 (1.24) .0

4、14 (.36) -8 .620 (15.75) .256 (6.50) .495 (12.57).500 (12.70).016 (.41) -10 .708 (17.98) .293 (7.44) .156 (3.96).620 (15.75).625 (15.88) .018 (.46) -12 1.024 (26.01) .424 (10.77) .745 (18.92).844 (21.44) .020 (.51) -16 1.112 (28.24) .461 (11.71) .995 (25.27).969 (24.61) .022 (.56) -20 1.266 (32.16)

5、.525 (13.34) 1.245 (31.62) 1.188 (30.18) .065 (1.65) .024 (.61) -24 1.399 (35.53) .580 (14.73) 1.495 (37.97) 1.375 (34.93) .026 (.66) -32 1.664 (42.27) .690 (17.53) 1.995 (50.67) 1.750 (44.45) .083 (2.11) .028 (.71) -40 1.885 (47.88) .781 (19.84) 2.370 (60.20) 2.062 (52.37) -48 2.062 (52.37) .854 (2

6、1.69) .250 (6.35)2.995 (76.07) 2.312 (58.72) .095 (2.41) .030 (.76) NOTES: 1. Dimensions are in inches. 2. Metric equivalents are for information only. 3. Unless otherwise specified, break all corners, radius .010/.005 inch (0.25/0.13 mm). 4. Break all edges and remove all burrs and slivers. 5. Oval

7、ity at bend shall not exceed 5% of tubing outside diameter. 6. Face of tube must be perpendicular to centerline of the tube within X total indicator reading. FIGURE 1. Elbow dimensions and configuration - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license

8、 from IHS-,-,-MS27235D 3 REQUIREMENTS: Dimensions and configurations: The design, construction, and physical dimensions shall be in accordance with MIL-DTL-5070 and figure 1 in case of conflict between this drawing and MIL-DTL-5070, this drawing shall govern. Intended use. This part is a component o

9、f MS27225 and MS27229. As part of an assembly this part is used on MS27226 and MS27230 hose to tube adapters. This item shall not be procured for stocking purposes. Materials: Materials shall be in accordance with MIL-DTL-5070. Finish: Finish shall be in accordance with MIL-DTL-5070. Platings are ap

10、plied after heat treats. Color identification: Color identification shall be in accordance with MIL-DTL-5070. Part or Identifying Number (PIN) example: MS 27235 -4 CZMaterial/finish code, see table I Dash number on figure 1 Specification number MS prefix TABLE I. Code for material and finish. Code D

11、ash size Material/finish CC -4 through -6 Carbon Steel - cadmium plating CZ -4 through -6 Carbon steel - zinc plating SS -4 through -6 Corrosion resistant steel - N/A AA -8 through -48 Aluminum - anodic coating TA -4 through -48 Titanium - anodized or fluoride phosphated. Changes from previous issue

12、. Marginal notations are not used in this revision to identify changes with respect to the previous issue, due to the extent of the changes. Referenced documents: In addition to MIL-DTL-5070, this document references the following: MS27225 MS27226 MS27229 MS27230 Provided by IHSNot for ResaleNo repr

13、oduction or networking permitted without license from IHS-,-,-MS27235D 4 CONCLUDING MATERIAL Custodians: Preparing activity: Army - AT DLA - CC Navy - AS Air Force - 99 (Project 4730-2005-053) DLA - CC Review activities: Army - AV Navy - MC, SA Air Force - 11, 70, 71 NOTE: The activities listed abov

14、e were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-